oil MAZDA MODEL 3 HATCHBACK 2004 (in English) Owner's Guide

8-19
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Inspecting Power Steering Fluid
Level
Inspect the fluid level in the reservoir at
each engine oil change with the engine off
and cold. Add fluid if necessary; it does
not require periodic changing.
The level must be kept between MIN and
MAX.
Visually examine the lines and hoses for
leaks and damage.
If new fluid is required frequently, consult
an Authorized Mazda Dealer. •Brake and clutch fluid will damage
painted surfaces. If brake or clutch
fluid does get on a painted surface,
wipe it off immediately.
•Using nonspecified brake and clutch
fluids (page 10-4) will damage the
systems. Mixing different fluids
will also damage them.
If the brake/clutch system
frequently requires new fluid,
consult an Authorized Mazda
Dealer.
CAUTIONPower Steering Fluid
To avoid damage to the power steering
pump, don’t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 19 Wednesday, August 6, 2003 8:51 AM

8-22
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
To inspect the washer fluid level in the
front reservoir, pull off the cap. Then,
holding your thumb over the hole in the
center of the cap, lift it straight up. The
fluid level can be seen from the fluid
column in the pipe. Add fluid if necessary.
Use plain water if washer fluid is
unavailable. But use only washer fluid in
cold weather to prevent it from freezing.All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the engine hood’s secondary
latch keeps the hood from opening when
the primary latch is released.
NOTE
Front and rear washer fluid is supplied
from the same reservoir.
Body Lubrication
J48C_8S18-EA-03I_Edition1.book Page 22 Wednesday, August 6, 2003 8:51 AM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Your Mazda’s headlights and fog lights
have replaceable halogen bulbs.
Replacing Exterior Light Bulbs
Replacing a headlight bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood.
3. Do the following procedure when
replacing the left headlight bulb.
Turn the screws counterclockwise and
remove them and the cover.
4. Find the high and low beam bulbs in
the rear of the headlight unit.
The outboard bulb is the LOW beam,
and the inboard one is the HIGH beam.
(page 8-36)
Xenon Fusion Bulb Replacement:
Replacing the xenon fusion bulbs by
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Do not replace the xenon
fusion bulbs by yourself. Consult an
Authorized Mazda Dealer when the
replacement is necessary.
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
WARNING
Screw
Cover
J48C_8S18-EA-03I_Edition1.book Page 37 Wednesday, August 6, 2003 8:51 AM

8-55
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I
Wa x i n g
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.
3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.

Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.

Bright-Metal Maintenance
•Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
•To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
•During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
Don’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 55 Wednesday, August 6, 2003 8:51 AM

8-57
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I

Dashboard Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
dashboard. They’ll damage and discolor
it. If these solutions get on the dashboard,
wipe them off immediately.

Cleaning the Upholstery and
Interior Trim
Vi ny l
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather*
Real leather isn’t uniform and may have
scars, scratches, and wrinkles. Clean it
with a leather cleaner or mild soap.
Wipe it with a damp
soft cloth; then dry
and buff it with a dry
soft cloth.Fabric
Remove dust and loose dirt from fabric
with a whisk broom or vacuum cleaner.
Clean it with a mild soap solution good
for upholstery and carpets. Remove fresh
spots immediately with a fabric spot
cleaner.
To keep the fabric looking clean and
fresh, take care of it. Otherwise its color
will be affected, it can be stained easily,
and its fire-resistance may be reduced.

Cleaning the Lap/Shoulder Belt
We b b i n g
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don’t bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.
Interior Care
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discoloration,
wrinkling, cracks and peeling.
CAUTION
Use only recommended cleaners and
procedures. Others may affect
appearance and fire-resistance.
Damaged Seat Belt:
Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have an Authorized
Mazda Dealer replace damaged belts
immediately.
CAUTION
WARNING
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 57 Wednesday, August 6, 2003 8:51 AM

8-58
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I

Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them with
glass cleaner. Follow the directions on the
container.
Don’t scrape or scratch the inside of
the rear window. You may damage the
rear window defroster grid.
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 58 Wednesday, August 6, 2003 8:51 AM

10-4
Form No. 8S18-EA-03I
Specifications

Engine

Electrical System

Lubricant Quality
* Refer to the recommended SAE viscosity numbers on page 8-13.
Specifications
ItemModel
2.0-liter engine 2.3-liter engine
Type DOHC-16V in-line, 4-cylinder
Bore×
Stroke 87.5 ×
83.1 mm (3.44 ×
3.27 in) 87.5 ×
94.0 mm (3.44 ×
3.70 in)
Displacement 1,999 ml (1,999 cc, 121.9 cu in) 2,261 ml (2,261 cc, 137.9 cu in)
Compression ratio 10.0 9.7
Item Classification
Battery 12V-40AH/5HR, 12V-52AH/5HR, 12V-55AH/5HR
Alternator 12 V - 90 A
Starter2.0-liter engine 12 V - 1.0 kW
2.3-liter engine 12 V - 1.4 kW
Spark-plug number NGK ITR6F 13
Spark-plug gap 1.25—1.35 mm (0.049—0.053 in)
NOTE
When cleaning the iridium plugs, do not use a wire brush. The fine particulate coating
on the iridium alloy and platinum tips could be damaged.
LubricantClassification
API Service ILSAC
Engine oil
*SL GF-III
Lubricant Classification
Manual transaxle oilAny temperatureAPI Service GL-4 or GL-5
SAE 75W-90
Above 10°
C (50°
F)API Service GL-4 or GL-5
SAE 80W-90
Automatic transaxle fluid ATF M-V
Power steering fluid ATF M-III or equivalent (e.g. Dexron® III)
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
J48C_8S18-EA-03I_Edition1.book Page 4 Wednesday, August 6, 2003 8:51 AM

10-5
Specifications
Form No. 8S18-EA-03I

Capacities
(Approximate Quantities)

Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
* With side protector
ItemUnit
L US qt Imp qt
Engine oilWith oil filter replacement 4.3 4.5 3.8
Without oil filter replacement 3.9 4.1 3.4
CoolantWith heater 7.5 7.9 6.6
Without heater 6.9 7.3 6.1
Manual transaxle oil 2.87 3.03 2.53
Automatic transaxle fluid 7.2 7.6 6.3
Fuel tank 5514.5
(US gal)12.1
(Imp gal)
ItemModel
4 Door 5 Door
Overall length(STD) 4,530 mm (178.3 in)—
(SAP) 4,540 mm (178.7 in) 4,485 mm (176.6 in)
Overall width
*1,755 mm (69.1 in) 1,755 mm (69.1 in)
Overall height 1,465 mm (57.7 in) 1,465 mm (57.7 in)
Front tread 1,530 mm (60.2 in) 1,530 mm (60.2 in)
Rear tread 1,515 mm (59.6 in) 1,515 mm (59.6 in)
Wheelbase 2,640 mm (103.9 in) 2,640 mm (103.9 in)
J48C_8S18-EA-03I_Edition1.book Page 5 Wednesday, August 6, 2003 8:51 AM

11-3
Index
Form No. 8S18-EA-03I
D
Dashboard Illumination ................... 5-30
Daytime Running Lights
.................. 5-47
Defroster
Rear window
............................. 5-52
Dimensions
...................................... 10-5
Door Locks
......................................... 3-7
Driving In Flooded Area
.................. 4-12
Driving Tips
....................................... 4-7
Automatic transaxle
.................. 5-16
Break-in period
........................... 4-7
Driving in flooded area
............. 4-12
Hazardous driving
....................... 4-8
Money-saving suggestions
.......... 4-7
Rocking the vehicle
.................... 4-9
Winter driving
............................. 4-9
E
Emergency Starting .......................... 7-15
Flooded engine
.......................... 7-15
Jump-starting
............................ 7-16
Push-starting
............................. 7-19
Emergency Towing
.......................... 7-20
Emission Control System
................... 4-3
Engine
Coolant
...................................... 8-15
Exhaust gas
................................. 4-5
Hood release
............................. 3-20
Oil
............................................. 8-13
Overheating
............................... 7-13
Starting
........................................ 5-3
Engine Compartment Overview
...... 8-12
Engine Coolant
Overheating
............................... 7-13
Engine Coolant Temperature
Gauge
............................................... 5-29
Exhaust Gas
....................................... 4-5
Exterior Care
.................................... 8-53
F
Flasher
Hazard warning
.........................5-53
Headlights
.................................5-44
Flat Tire
..............................................7-3
Changing
.....................................7-6
Spare tire and tool storage
...........7-3
Flexible Floor Board
........................6-45
Fluids
Classification
.............................10-4
Owner maintenance
...................8-10
Fog Lights
........................................5-48
Foot Brake
..........................................5-4
Front Seats
..........................................2-2
Fuel
Filler lid and cap
.......................3-19
Gauge
........................................5-29
Requirements
..............................4-2
Tank capacity
............................10-5
Fuses
.................................................8-46
Panel description
.......................8-48
Replacement
..............................8-46
G
Gauges ..............................................5-26
Glove Box
........................................6-42
H
Hazard Warning Flasher ...................5-53
Hazardous Driving
.............................4-8
Headlights
Control
......................................5-44
Flashing
.....................................5-46
High-low beam
..........................5-46
Leveling
....................................5-46
On reminder
..............................5-45
J48C_8S18-EA-03I_Edition1.book Page 3 Wednesday, August 6, 2003 8:51 AM

11-6
Index
Form No. 8S18-EA-03I
T
Tire Pressure Monitoring System .... 5-22
System error activation
............. 5-24
Tire pressure monitoring system
warning light
............................. 5-23
Tires and wheels
....................... 5-24
Tires
Flat Tire
...................................... 7-3
Inflation pressure
...................... 8-31
Replacement
............................. 8-33
Rotation
.................................... 8-32
Snow tires
................................. 4-10
Spare tire and tool storage
.......... 7-3
Specifications
........................... 10-8
Tire chains
................................ 4-11
Uniform tire quality grading system
(UTQGS)
.................................. 9-16
Tool
.................................................... 7-3
Towing
Description
............................... 7-20
Emergency towing
.................... 7-20
Recreational towing
.................. 7-23
Towing caravan and trailers
(Europe)
.................................... 4-13
Trailer towing
........................... 4-13
Trailer Towing
................................. 4-13
Trip Meter
........................................ 5-27
Trunk Lid
......................................... 3-13
Trunk Light
...................................... 3-15
Turn and Lane-Change Signals
....... 5-47
V
Vanity Mirrors ................................. 6-35
Vehicle Information Labels
............. 10-2
W
Warning Lights ................................ 5-31
ABS
........................................... 5-35
Air bag system
.......................... 5-36
Automatic transaxle
.................. 5-38
Brake system
............................. 5-33
Charging system
....................... 5-34
Check engine
............................. 5-35
Door-ajar
................................... 5-38
Engine oil pressure
.................... 5-34
Front seat belt pretensioner
system
....................................... 5-36
Low fuel
.................................... 5-36
Low washer fluid level
............. 5-38
seat belt
..................................... 5-37
Tire pressure monitoring
system
....................................... 5-38
Warranty
............................................. 9-9
Washer Fluid
.................................... 8-21
Weights
............................................ 10-6
Wheel Replacement
......................... 8-34
Windows
Power windows
......................... 3-17
Windshield Washer
.......................... 5-51
Windshield Wipers
........................... 5-49
Blades replacement
................... 8-24
Winter Driving
................................... 4-9
J48C_8S18-EA-03I_Edition1.book Page 6 Wednesday, August 6, 2003 8:51 AM