sensor MAZDA MODEL 3 HATCHBACK 2004 (in English) Owner's Guide

8-23
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
This air filter may be cleaned with
compressed air and reused, or replaced,
depending on its condition. Unless it is
very dirty, simply shake it to remove
foreign particles. Each time you inspect it,
wipe inside the air cleaner housing with a
damp cloth.

Replacing the Air Filter
1. Make sure the ignition switch is turned
off.
2. Remove the battery cover and battery
duct.3. Unfasten the clamps.
4. Lift off the air filter cover and remove
the filter.
5. Wipe inside the air cleaner housing
with a damp cloth.
6. Clean or replace the filter.
7. Install in the reverse order of removal.
Replace the filter according to the
Scheduled Maintenance (page 8-3).
Air Filter
Don’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than the recommended intervals.
Use a Mazda genuine air filter. Use of
other filters could damage the airflow
sensor.
CAUTION
CAUTION
Battery duct
Battery cover
Clamp
Air filter cover
Air filter
J48C_8S18-EA-03I_Edition1.book Page 23 Wednesday, August 6, 2003 8:51 AM

8-24
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.

Replacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Slide the assembly downward; then lift
it off the arm.
Wiper Blades
•Hot waxes applied by automatic car
washers have been known to affect
the cleanability of windows.
•To prevent damage to the wiper
blades, don’t use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
•When the wiper lever is in the
AUTO position and the ignition
switch is in the ON position, the
wipers may move automatically in
the following cases:
If the windshield above the rain
sensor is touched.
If the windshield above the rain
sensor is wiped with a cloth.
If the windshield is given a
shock.
If the rain sensor is given a shock
from inside the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When washing or
servicing your Mazda, make sure the
wiper lever is in the OFF position.
CAUTION
To prevent damage to the wiper arms
and other components, don’t move the
wipers by hand.
To prevent damage to the windshield,
don’t let the wiper arm fall on it.
CAUTION
Push
Plastic locking clip
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 24 Wednesday, August 6, 2003 8:51 AM

8-33
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Replacing a TireIf a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
You should replace it before the band is
across the entire tread.

Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it’s properly
inflated and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (4.2 kgf/
cm
2 or bar, 60 psi).
Worn Tires:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Always use tires that are in good
condition.
(With Tire Pressure Monitoring
System)

When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the
tire pressure sensors may be damaged.
NOTE
(With Tire Pressure Monitoring
System)

•When tires with steel wire
reinforcement in the sidewalls are
used, the system may not function
correctly even with a genuine
wheel. (page 5-24)
•Be sure to install the tire pressure
sensors whenever tires or wheels are
replaced. (page 5-24)
WARNING
CAUTIONNew tread Worn treadTread wear indicator
J48C_8S18-EA-03I_Edition1.book Page 33 Wednesday, August 6, 2003 8:51 AM

8-34
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Replacing a Wheel
•Don’t use your temporary spare tire
rim with a snow tire or a
conventional tire. Neither will
properly fit and could damage both
tire and rim.
•The temporary spare tire has a tread
life of up to 5,000 km (3,000 miles),
depending on road conditions and
driving habits.
•The temporary spare tire is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tire with the same type
of temporary spare (page 8-33).
CAUTION
Using a Wrong-Sized Wheel:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident. Always use
wheels of the correct size on your
vehicle.
•A wrong-sized wheel may
adversely affect:
Tire fit
Wheel and bearing life
Ground clearance
Snow-chain clearance
Speedometer calibration
Headlight aim
Bumper height
Tire Pressure Monitoring System
•(With Tire Pressure Monitoring
System)

When replacing/repairing the
tires or wheels or both, have the
work done by an Authorized
Mazda Dealer, or the tire
pressure sensors may be
damaged.
The wheels equipped on your
Mazda are specially designed for
installation the tire pressure
sensors. Do not use non-genuine
wheels, otherwise it may not be
possible to install the tire
pressure sensors.
WARNING
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 34 Wednesday, August 6, 2003 8:51 AM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
NOTE
Be sure to install the tire pressure
sensors whenever tires or wheels are
replaced. (page 5-24)
J48C_8S18-EA-03I_Edition1.book Page 35 Wednesday, August 6, 2003 8:51 AM

8-48
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Fuse Panel Description
Fuse block (Engine compartment)
12 3 45 6
789 10
11 12
13 14
15 16
17 18
1920 2122 23
24 25 26
27 2829
3031 3233 3435 36
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 FAN 40A Cooling fan
2 P/ST 80A EHPAS
3BTN 40AFor protection of
various circuits
4HEAD 40AHeadlights
5PTC 80A—
6GLOW 60A—
7ABS 1 30A
ABS
*
8ABS 2 20A
ABS*
9 ENGINE 30AFor protection of
various circuits
10—— —
11 IG KEY 1 30A Ignition switch
12 STARTER 20A Starter clutch
13 IG KEY 2 30A Ignition switch
14—— —
15 HEATER 40A Blower motor
16—— —
17 DEFOG 40ARear window
defroster
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
18—— —
19 ABS IG 10A
ABS
*
20 FOG 15A
Fog lights*
21 HORN 15A Horn
22—— —
23 H/CLEAN 20A—
24 F/PUMP 15A Fuel pump
25 P/ST IG 10A Power steering
26 A/C MAG 10A Air conditioner
27 ALT 10A—
28—— —
29—— —
30 ENG +B 10A PCM
31 ROOM 15A Interior lights
32
ENG BAR 410AO2 heater
33
ENG BAR 310AO2 heater
34 EGI INJ 10A Injector
35
ENG BAR 110A Air flow sensor
36ENG BAR 210A EGR control valve
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 48 Wednesday, August 6, 2003 8:51 AM

8-53
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I
Follow all
label and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.

Maintaining the Finish
Wa s h i n g
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface
when:
•The vehicle is washed without first
rinsing off dirt and other foreign
matter.
•The vehicle is washed with a rough,
dry, or dirty cloth.
•The vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
•Cleansers or wax containing abrasives
are used.Exterior Care
When the wiper lever is in the AUTO
position and the ignition switch is in
the ON position, the wipers may move
automatically in the following cases:
•If the windshield above the rain
sensor is touched.
•If the windshield above the rain
sensor is wiped with a cloth.
•If the windshield is given a shock.
•If the rain sensor is given a shock
from inside the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When washing or
servicing your Mazda, make sure the
wiper lever is in the OFF position.
CAUTION
NOTE
•Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
•Scratches are more noticeable on
vehicles with darker paint finishes.
J48C_8S18-EA-03I_Edition1.book Page 53 Wednesday, August 6, 2003 8:51 AM