maintenance MAZDA MODEL 3 HATCHBACK 2004 (in English) Workshop Manual

8-43
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
High-mount brake light
4 Door
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
rear trim.
2. Disconnect the electrical connector
from the socket.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.5 Door
1. Remove the liftgate upper trim.
2. Disconnect the electrical connector
from the socket.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Removal
Installation
Trunk rear trim
Socket
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Liftgate upper trim
Socket
J48C_8S18-EA-03I_Edition1.book Page 43 Wednesday, August 6, 2003 8:51 AM

8-44
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.

Replacing Interior Light Bulbs
Overhead light/Map lights (Front)*
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
Edge
Socket
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 44 Wednesday, August 6, 2003 8:51 AM

8-45
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Overhead light (Rear)
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Trunk light (4 Door)
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.Luggage compartment light (5 Door)
1. Insert your finger as shown in the
figure and remove the unit.
2. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse order
of removal.
Edge
J48C_8S18-EA-03I_Edition1.book Page 45 Wednesday, August 6, 2003 8:51 AM

8-46
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.

Fuse Replacement
If the electrical system doesn’t work, first
inspect fuses on the front passenger’s side
below the glove box.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.3. Turn the knobs counterclockwise and
lower the fuse block.
4. Locate the position of the suspected
fuse by using the chart inside the fuse
block cover.
5. Pull the fuse straight out with the fuse
puller provided on the inside of the
engine compartment fuse block cover.
Fuses
Cover
Fuse block cover
Fuse puller
J48C_8S18-EA-03I_Edition1.book Page 46 Wednesday, August 6, 2003 8:51 AM

8-47
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
6. Inspect it and replace if it’s blown.
7. Push in a new fuse of the same rating,
and make sure it fits tightly. If it
doesn’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the SPARE circuit.
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
one of the same rating
.
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Normal Blown
CAUTION
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer.
Fuse block cover
Normal Blown
Main fuse
J48C_8S18-EA-03I_Edition1.book Page 47 Wednesday, August 6, 2003 8:51 AM

8-48
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Fuse Panel Description
Fuse block (Engine compartment)
12 3 45 6
789 10
11 12
13 14
15 16
17 18
1920 2122 23
24 25 26
27 2829
3031 3233 3435 36
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 FAN 40A Cooling fan
2 P/ST 80A EHPAS
3BTN 40AFor protection of
various circuits
4HEAD 40AHeadlights
5PTC 80A—
6GLOW 60A—
7ABS 1 30A
ABS
*
8ABS 2 20A
ABS*
9 ENGINE 30AFor protection of
various circuits
10—— —
11 IG KEY 1 30A Ignition switch
12 STARTER 20A Starter clutch
13 IG KEY 2 30A Ignition switch
14—— —
15 HEATER 40A Blower motor
16—— —
17 DEFOG 40ARear window
defroster
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
18—— —
19 ABS IG 10A
ABS
*
20 FOG 15A
Fog lights*
21 HORN 15A Horn
22—— —
23 H/CLEAN 20A—
24 F/PUMP 15A Fuel pump
25 P/ST IG 10A Power steering
26 A/C MAG 10A Air conditioner
27 ALT 10A—
28—— —
29—— —
30 ENG +B 10A PCM
31 ROOM 15A Interior lights
32
ENG BAR 410AO2 heater
33
ENG BAR 310AO2 heater
34 EGI INJ 10A Injector
35
ENG BAR 110A Air flow sensor
36ENG BAR 210A EGR control valve
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 48 Wednesday, August 6, 2003 8:51 AM

8-49
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Fuse block (Passenger’s side)
37 38 39 4041 42
43 44 4546
47 48 49 5051
52 5354 55 56 5758
59 60 61 6263 64
65 66 67 68 6970
71 72 73 74 75 76 77 78 79 80 81 82 83 84 8586
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
37 D/LOCK 2 15A Power door lock
38—— —
39HEAD
HIGH L10AHeadlight high
beams (LH)
40HEAD
HIGH R10AHeadlight high
beams (RH)
41—— —
42—— —
43 CIGAR 15A Lighter
44 RADIO 7.5A Audio system
45 MIRROR 10APower control
mirror
46 TAIL R 7.5ATaillight (RH),
Parking lights (RH)
License plate lights
47 OBD 10AFor protection of
various circuits
48—— —
49 TR/LOCK 20A—
50 CPU PWR 10A Control unit
51 HAZARD 15A
Turn signals, Hazard
warning flashers
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
52SUN
RO O F20A
Moonroof
*
53 WASHER 20AFront washer, Rear
window wiper and
washer
54—— —
55 P/WIND R 30A—
56 P/WIND L 30A—
57 ALARM 7.5A—
58 M/DEF 7.5A Mirror Defroster
59—— —
60HEAD
LOW R15AHeadlight low
beams (RH),
Headlight leveling
*
61HEAD
LOW L15AHeadlight low
beams (LH)
62—— —
63—— —
64—— —
65 SAS 10ASupplemental
restraint system
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 49 Wednesday, August 6, 2003 8:51 AM

8-50
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
66 METER 10AInstrument cluster,
Immobilizer
system, Shift lock
system
67 IGNITION 20A
ABS
*, EHPAS*
68 WIPER 20A Windshield wiper
69 ENGINE 20AFor protection of
various circuits
70 IG SIG 10A
Auto wiper
*
71 SAS 2 7.5ASupplemental
restraint system
72—— —
73—— —
74SEAT
WA R M20A—
75 D/LOCK 1 25A Power door lock
76 A/C 10AAir conditioner,
Heater control unit
77 P/WIND L 30APower window
(LH)
*
78 P/WIND R 30APower window
(RH)*
79 BACK 10A Reverse lights
80SUN
RO O F7.5A
Moonroof
*
81 TAIL L 7.5ATaillights (LH),
Parking lights (LH)
82 ILLUMI 7.5A Illumination
83—— —
84—— —
85—— —
86—— —
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 50 Wednesday, August 6, 2003 8:51 AM

8-51
Maintenance and Care
Form No. 8S18-EA-03I
Appearance Care
The paintwork on your Mazda represents
the latest technical developments in
composition and methods of application.
Environmental hazards, however, can
harm the paint’s protective properties, if
proper care is not taken.
Here are some examples of possible
damage, with tips on how to prevent them.

Etching Caused by Acid Rain or
Industrial Fallout
Occurrence
Industrial pollutants and vehicle
emissions drift into the air and mix with
rain or dew to form acids. These acids can
settle on a vehicle’s finish. As the water
evaporates, the acid becomes concentrated
and can damage the finish.
And the longer the acid remains on the
surface, the greater the chance is for
damage.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you suspect that acid rain has settled on
your vehicle’s finish.

Damage Caused by Bird
Dropping, Insects, or Tree Sap
Occurrence
Bird droppings contain acids. If these
aren’t removed they can eat away the clear
and color base coat of the vehicle’s
paintwork.
When insects stick to the paint surface
and decompose, corrosive compounds
form. These can erode the clear and color
base coat of the vehicle’s paintwork if
they are not removed.
Tree sap will harden and adhere
permanently to the paint finish. If you
scratch the sap off while it is hard, some
vehicle paint could come off with it.
Prevention
It is necessary to have your Mazda
washed and waxed to preserve its finish
according to the instructions in this
section. This should be done as soon as
possible.
Bird droppings can be removed with a soft
sponge and water. If you are traveling and
these are not available, a moistened tissue
may also take care of the problem. The
cleaned area should be waxed according
to the instructions in this section.
Insects and tree sap are best removed with
a soft sponge and water or a commercially
available chemical cleaner.
Another method is to cover the affected
area with dampened newspaper for one to
two hours. After removing the newspaper,
rinse off the loosened debris with water.
How to Minimize
Environmental Paint
Damage
J48C_8S18-EA-03I_Edition1.book Page 51 Wednesday, August 6, 2003 8:51 AM

8-52
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I

Water Marks
Occurrence
Rain, fog, dew, and even tap water can
contain harmful minerals such as salt and
lime. If moisture containing these
minerals settles on the vehicle and
evaporates, the minerals will concentrate
and harden to form white rings. The rings
can damage your vehicle’s finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you find water marks on your vehicle’s
finish.

Paint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle’s tires hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel.
NOTE
•The paint chipping zone varies with
the speed of the vehicle. For
example, when traveling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
•In low temperatures a vehicle’s
finish hardens. This increases the
chance of paint chipping.
•Chipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according to
the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.
J48C_8S18-EA-03I_Edition1.book Page 52 Wednesday, August 6, 2003 8:51 AM