fuel MAZDA MODEL 3 HATCHBACK 2015 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL 3 HATCHBACK, Model: MAZDA MODEL 3 HATCHBACK 2015Pages: 689, PDF Size: 7.08 MB
Page 109 of 689
3–31
Before Driving
Fuel and Emission
Fuel-Filler Flap and Cap
WARNING
When removing the fuel-fi ller cap,
loosen the cap slightly and wait for any
hissing to stop, then remove it:
Fuel spray is dangerous. Fuel can
burn skin and eyes and cause illness
if ingested. Fuel spray is released
when there is pressure in the fuel tank
and the fuel-fi ller cap is removed too
quickly.
Before refuelling, stop the engine, and
always keep sparks and fl ames away
from the fi ller neck:
Fuel vapour is dangerous. It could be
ignited by sparks or fl ames causing
serious burns and injuries.
Additionally, use of the incorrect fuel-
fi ller cap or not using a fuel-fi ller cap
may result in a fuel leak, which could
result in serious burns or death in an
accident.
Do not continue refuelling after
the fuel pump nozzle shuts off
automatically:
Continuing to add fuel after the fuel
pump nozzle has shut off automatically
is dangerous because overfi lling the
fuel tank may cause fuel overfl ow or
leakage. Fuel overfl ow and leakage
could damage the vehicle and if the
fuel ignites it could cause a fi re and
explosion resulting in serious injury or
death.
CAUTION
Always use only a designated Mazda
fuel-fi ller cap or an approved equivalent,
available at an expert repairer, we
recommend an Authorised Mazda
Repairer. The wrong cap can result in
a serious malfunction of the fuel and
emission control systems.
Fuel-Filler Flap
To open, pull the remote fuel-fi ller fl ap
release.
To close, press the fuel-fi ller fl ap until it
locks securely.
Remote fuel-filler
flap release
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 110 of 689
3–32
Before Driving
Fuel and Emission
Fuel-Filler Cap
To remove the fuel-fi ller cap, turn it
anticlockwise.
Attach the removed cap to the inner side
of the fuel fl ap.
To close the fuel-fi ller cap, turn it
clockwise until a click is heard.
Open
Close
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 131 of 689
3–53
Before Driving
Driving Tips
Running-In
No special running-in is necessary, but
a few precautions in the fi rst 1,000 km
(600 miles) may add to the performance,
economy, and life of the vehicle.
Do not race the engine.
Do not maintain one constant speed,
either slow or fast, for a long period of
time.
Do not drive constantly at full-throttle or
high engine rpm for extended periods of
time.
Avoid unnecessary hard stops.
Avoid full-throttle starts.
Do not tow a trailer.
Saving Fuel and
Protection of the
Environment
How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save fuel and
reduce CO2.
Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
Avoid fast starts.
Drive at lower speeds.
Anticipate when to apply the brakes
(avoid sudden braking).
Follow the maintenance schedule
(page 6-3 ) and have an expert repairer,
we recommend an Authorised Mazda
Repairer perform inspections and
servicing.
Use the air conditioner only when
necessary.
Slow down on rough roads.
Keep the tyres properly infl ated.
Do not carry unnecessary weight.
Do not rest your foot on the brake pedal
while driving.
Keep the wheels in correct alignment.
Keep windows closed at high speeds.
Slow down when driving in crosswinds
and headwinds.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 151 of 689
*Some models.4–1
4When Driving
Information concerning safe driving and stopping.
Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-12
i-stop
* ........................................... 4-13
Instrument Cluster and Display ...... 4-24
Meters and Gauges ....................... 4-24
Multi-information Display
* .......... 4-32
Active Driving Display* ............... 4-38
Warning/Indicator Lights ............. 4-40
Transaxle ............................................ 4-47
Manual Transaxle Operation ........ 4-47
Automatic Transaxle Controls ..... 4-50
Switches and Controls ...................... 4-62
Lighting Control ........................... 4-62
Front Fog Lights
* ......................... 4-70
Rear Fog Light* ............................ 4-71
Turn and Lane-Change Signals ...... 4-72
Windscreen Wipers and Washer ...... 4-73
Rear Window Wiper and
Washer
*......................................... 4-77
Headlight Washer* ........................ 4-78
Rear Window Defogger ............... 4-78
Horn ............................................. 4-80
Hazard Warning Flasher ............... 4-80
Brake .................................................. 4-82
Brake System ............................... 4-82
Emergency Stop Signal System ...... 4-85
Hill Launch Assist (HLA)* ........... 4-85 ABS/TCS/DSC ................................... 4-87
Antilock Brake System (ABS) ...... 4-87
Traction Control System (TCS)*...... 4-88
Dynamic Stability Control
(DSC)
* .......................................... 4-89
i-ELOOP ............................................ 4-91
i-ELOOP
* ..................................... 4-91
Fuel Economy Monitor ..................... 4-94
Fuel Economy Monitor
* ............... 4-94
Power Steering................................... 4-99
Power Steering ............................. 4-99
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 155 of 689
4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-40 ).
NOTE
(SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
The key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
The engine can be started when the
push button start is pressed from off,
ACC, or ON.
The push button start system
functions (function which can start
the engine by only carrying the
key) can be deactivated to prevent
any possible adverse effect on a
user wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable
to start the engine by carrying the
key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 158 of 689
4–8
When Driving
Start/Stop Engine
NOTE
After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to
the ON position.
(SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
After pressing the push button start
and before the engine starts, the
operation sound of the fuel pump
motor from near the fuel tank can be
heard, however, this does not indicate
a malfunction.
NOTE
(SKYACTIV-D 2.2)
When starting the engine, do
not release the clutch pedal
(manual transaxle) or the brake
pedal (automatic transaxle) until
the glow indicator light in the
instrument cluster turns off and
the engine starts, after pressing the
push button start.
If the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) is released
before the engine starts, depress
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle) again and press the push
button start to start the engine.
If the ignition is left switched ON
for a long period of time without
the engine running after the glow
plugs are warmed up, the glow
plugs may warm up again which
will illuminate the glow indicator
light.
The starter does not rotate until the
glow indicator light turns off.
8. After starting the engine, let it idle
for about ten seconds (Prohibited in
Germany).
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 163 of 689
*Some models.4–13
When Driving
Start/Stop Engine
i-stop *
The i-stop (idling stop) function automatically stops the engine when the vehicle is stopped
at a traffi c light or stuck in traffi c after the engine has been warmed up (SKYACTIV-G 1.5
, SKYACTIV-G 2.0) or other times when the engine is not cold (SKYACTIV-D 2.2), and
then restarts the engine automatically to resume driving. The system provides improved fuel
economy, reduced exhaust gas emissions, and eliminates idling noise while the engine is
stopped.
The driver is notifi ed of a system malfunction or the operation conditions by the i-stop
warning light (amber), i-stop indicator light (green), i-stop warning beep, and control status
display.
Engine stop and restart functions
(Manual transaxle)
1 . (Except European model)
The i-stop indicator light (green) illuminates when the i-stop conditions are met while the
vehicle is being driven.
2. Depress the brake pedal and then the clutch pedal, and bring the vehicle to a complete
stop.
3. After bringing the vehicle to a stop, shift the lever to the neutral position while
depressing the clutch pedal. The engine automatically stops after the clutch pedal is
released. The i-stop indicator light (green) also illuminates while the i-stop function is
operating.
4. To restart the engine, depress the clutch pedal (i-stop indicator light (green) turns off).
The i-stop indicator light (green) illuminates if the i-stop function conditions are met
again while driving (except European model).
Engine stop Restart
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 166 of 689
4–16
When Driving
Start/Stop Engine
NOTE
(Automatic transaxle)
The selector lever is in the D/M position (not second gear fi xed mode) or the N
position.
The automatic transaxle fl uid has warmed up suffi ciently.
The automatic transaxle fl uid temperature is not abnormally high.
The steering wheel is positioned so that the wheels are pointed nearly straight ahead
(if force is applied to the steering wheel even with the wheels pointed straight ahead,
the i-stop function may not operate. Loosen your grip on the steering wheel to allow
the i-stop function to operate).
The brake pedal is depressed to stop the vehicle (if the i-stop indicator light (green)
fl ashes without the i-stop function operating, it is possible that the brake pedal
has not been depressed suffi ciently. Depress the brake pedal a little more strongly
(except European model)).
Emergency braking is not applied.
The vehicle is not stopped on a steep grade in a place such as a multilevel car
parking facility.
(SKYACTIV-D 2.2)
The fuel injection learning, which occurs periodically and automatically, is not
performed.
If any one of the following conditions occurs, extra time may be required for the
engine to stop automatically.
Battery power is depleted as a result of not using the vehicle for a long period.
The ambient temperature is high or low.
The battery leads have been disconnected for battery replacement and then
reconnected.
(SKYACTIV-D 2.2)
Particulate Matter (PM) is eliminated by the diesel particulate fi lter.
For safety reasons, if any one of the following operations is performed after the engine
has been automatically stopped, the i-stop warning light (amber) illuminates and the
engine will not restart automatically even if the clutch pedal is depressed (manual
transaxle) or the brake pedal is released (automatic transaxle). If this occurs, use the
standard engine starting procedure to start the engine.
The bonnet is opened.
The driver intends to get out of the vehicle (driver's seat belt is unfastened and
driver's door is opened).
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 174 of 689
4–24
When Driving
Instrument Cluster and Display
Meters and Gauges
Type A
Type B
Type C
Steering Switch (Digital Speed Meter Type)
(Analog Speed Meter Type (With Tachometer))
(Analog Speed Meter Type (Without Tachometer))
Some models.
Instrument Cluster
Speedometer .......................................................................................................... page 4-25
Odometer, Trip Meter and Trip Meter Selector .................................................... page 4-25
Tachometer ............................................................................................................ page 4-27
Fuel Gauge ............................................................................................................ page 4-27
Instrument panel Illumination ............................................................................... page 4-28
Outside Temperature Display ................................................................................ page 4-29
Cruise Control Set Vehicle Speed Display ............................................................ page 4-29
Multi Information Display .................................................................................... page 4-32
Active Driving Display ......................................................................................... page 4-38
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 176 of 689
4–26
When Driving
Instrument Cluster and Display
NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
After the ignition is switched to off
from ON.
After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed. The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
NOTE
(Vehicles with type C/type D audio) If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
Refer to Fuel Economy Monitor on
page 4-94 .
Only the trip meters record tenths of
kilometres (miles).
The trip record will be erased when:
The power supply is interrupted
(blown fuse or the battery is
disconnected).
The vehicle is driven over 9999.9
km (mile).
. B [ E B @ & ' & & " @ & E J U J P O J O E C