warning MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL 3 HATCHBACK, Model: MAZDA MODEL 3 HATCHBACK 2015Pages: 689, PDF Size: 7.08 MB
Page 570 of 689
6–74
Maintenance and Care
Appearance Care
CAUTION
Do not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodised
aluminium parts. This may damage
the protective coating; also, cleaners
and detergents may discolour or
deteriorate the paint.
(With detachable aerial) To prevent damaging the aerial,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
Pay special attention to removing salt, dirt,
mud, and other foreign material from the
underside of the wings, and make sure the
drain holes in the lower edges of the doors
and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits
can damage the fi nish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the fi nish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
When using an automatic car wash
Retract the door mirrors.
The automatic car wash brushes could
reduce the paint lustre or hasten paint
deterioration.
When using a high water pressure car
wash
High water temperature and high water
pressure car washers are available
depending on the type of car wash
machine. If the car washer nozzle is
put too close to the vehicle, the force of
the spray could damage or deform the
molding, affect the sealability of parts,
and allow water to penetrate the interior.
Keep a suffi cient space (30 cm (12 in) or
more) between the nozzle and the vehicle.
In addition, do not spend too much time
spraying the same area of the vehicle, and
be very careful when spraying between
gaps in doors and around windows.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 573 of 689
6–77
Maintenance and Care
Appearance Care
Plastic Part Maintenance
When cleaning the plastic lenses of
the lights, do not use petrol, paraffi n,
rectifi ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signifi cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, fl ush with water
immediately.
If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fl uids such as petrol,
oil, engine coolant, or battery fl uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or fl uids using a soft
cloth immediately.
High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
Interior Care
WARNING
Do not spray water in the cabin:
Splashing water on electrical parts
such as the audio unit and switches
is dangerous as it could cause a
malfunction or a fi re.
Instrument panel Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
instrument panel. They will damage and
discolour the instrument panel. If these
solutions get on the instrument panel, wipe
them off immediately.
CAUTION
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discolouration,
wrinkling, cracks and peeling.
Instrument panel top (soft pad)
Extremely soft material is used for the
soft pad surface. When cleaning, it is
recommended that you use a clean towel
dampened in a mild detergent to remove
soiling.
If the soft pad surface is rubbed harshly,
it could result in the surface being
damaged leaving white scratch marks.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 575 of 689
6–79
Maintenance and Care
Appearance Care
CAUTION
Use only recommended cleaners
and procedures. Others may affect
appearance and fi re-resistance.
Panel
When the interior panels need to be
cleaned, use soft material such as a soft
cloth soaked in clean water and wrung
out well and lightly wipe off dirt from
the surface. If a panel requires further
cleaning, use the following procedure.
1. Wipe dirt off using a soft cloth soaked
in mild detergent (about 5% solution).
2. Wipe off any remaining detergent
using a cloth soaked in clean water and
wrung out well.
NOTE
Do not wipe leather parts using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
or petrol. Otherwise, it may cause
discolouration or stains.
Scratches or nicks on the panels and
metallic trim resulting from the use
of a hard brush or cloth may not be
repairable.
Be particularly careful when cleaning
high lustre panels and metallic trim
as they can be easily scratched.
Maintenance of the Active Driving
Display
The combiner and mirror surface have a
special coating. When cleaning, do not use
a hard or rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving display,
wipe it off immediately. Otherwise, the
combiner and mirror could be damaged
and the surface coating could be scratched.
Use a fi ne, soft cloth such as those used
for cleaning eyeglasses.
Cleaning the Lap/Shoulder Belt
Webbing
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Do not bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is no
remaining moisture before retracting them.
WARNING
Have an expert repairer, we
recommend an Authorised Mazda
Repairer replace damaged seat belts
immediately:
Using damaged seat belts is dangerous.
In a collision, damaged belts cannot
provide adequate protection.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 577 of 689
*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
Parking in an Emergency ................... 7-2
Parking in an Emergency ............... 7-2
Roadside Emergency Triangle
Retaining Strap
* ............................. 7-2
Flat Tyre ............................................... 7-3
Spare Tyre and Tool Storage .......... 7-3
Emergency Flat Tyre Repair Kit* ........ 7-8
Changing a Flat Tyre (With spare
tyre) .............................................. 7-15
Battery Runs Out .............................. 7-21
Jump-Starting ............................... 7-21
Emergency Starting .......................... 7-24
Starting a Flooded Engine (MZR 1.6,
SKYACTIV-G 1.5 and SKYACTIV-G
2.0) ............................................... 7-24
Push-Starting ................................ 7-24
Running Out of Fuel (SKYACTIV-D
2.2) ............................................... 7-25
Overheating ....................................... 7-26
Overheating .................................. 7-26
Emergency Towing ............................ 7-28
Towing Description ...................... 7-28
Towing Hooks .............................. 7-29 Warning/Indicator Lights and Warning
Sounds ................................................ 7-32
If a Warning Light Turns On or
Flashes .......................................... 7-32
Message Indicated in Multi-
information Display ..................... 7-45
Message Indicated on Display* ...... 7-47
Warning Sound is Activated ......... 7-49
When Liftgate/Boot Lid Cannot be
Opened ............................................... 7-54
When Liftgate/Boot Lid Cannot be
Opened ......................................... 7-54
Active Driving Display Does Not
Operate ............................................... 7-56
If the Active Driving Display does not
operate .......................................... 7-56
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 578 of 689
*Some models.7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffi c hazard
and that they must take extreme caution
when near it.
Depress the hazard warning fl asher and
all the direction indicators will fl ash. The
hazard warning indicator lights in the
instrument cluster fl ash simultaneously.
NOTE
The direction indicators do not work
when the hazard warning lights are
on.
Check local regulations about the use
of hazard warning lights while the
vehicle is being towed to verify that
it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
Keep the roadside emergency triangle in
the right side trim and secure it with the
strap.
Saloon
Strap
Hatchback
Strap
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 582 of 689
*Some models.7–6
If Trouble Arises
Flat Tyre
4. Insert the cover tabs and install the
cover.
(Saloon)
Tabs
Tabs (Hatchback)
NOTE
Verify that the cover is securely
installed.
Maintenance
Always keep the jack clean.
Make sure the moving parts are kept
free from dirt or rust.
Make sure the screw thread is
adequately lubricated.
Spare Tyre *
Your Mazda has a temporary spare tyre.
The temporary spare tyre is lighter and
smaller than a conventional tyre, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tyres should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare tyre
on the front wheels (driving wheels):
Driving with the temporary spare tyre
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tyre to the front wheel and install the
temporary spare tyre to the rear.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 584 of 689
*Some models.7–8
If Trouble Arises
Flat Tyre
Emergency Flat Tyre
Repair Kit
*
The emergency fl at tyre repair kit included
with your Mazda is for a temporary repair
of a slightly damaged fl at tyre resulting
from running over nails or similar sharp
objects on the road surface.
Perform the emergency fl at tyre repair
without removing the nail or similar sharp
object which punctured the tyre.
NOTE
Your vehicle is not equipped with a
spare tyre. In the event of a fl at tyre,
use the emergency fl at tyre repair kit
to repair the tyre temporarily. When
doing the repair, refer to the instructions
included in the emergency fl at tyre
repair kit. If an emergency repair was
performed on a fl at tyre using the
emergency fl at tyre repair kit, have
an expert repairer, we recommend an
Authorised Mazda Repairer, repair or
replace the tyre as soon as possible.
Emergency Flat Tyre Repair Kit
The emergency fl at tyre repair kit includes
the following items.
CompressorSealant bottle Speed restriction
stickerInstructions
WARNING
Do not allow children to touch the tyre
sealant:
Ingestion of tyre sealant is
dangerous. In the event tyre sealant
is accidentally swallowed, drink
large amounts of water immediately
and seek medical assistance.
Tyre sealant that comes into contact
with the eyes and skin is dangerous.
If tyre sealant enters the eyes or
contacts the skin, fl ush immediately
with large amounts of water and
seek medical assistance.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 585 of 689
7–9
If Trouble Arises
Flat Tyre
NOTE
The tyre sealant cannot be reused.
Purchase new tyre sealant at an
Authorised Mazda Repairer.
The emergency fl at tyre repair kit
cannot be used in the following
cases.
Consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
The period of effective use for
the tyre sealant has expired. (The
period of effectiveness is indicated
on the bottle label.)
The tear or puncture exceeds about
4 mm (0.16 in).
The damage has occurred to an
area of the tyre other than the
tread.
The vehicle has been driven with
nearly no air remaining in the tyre.
The tyre has come off the wheel
rim.
Damage to the wheel rim has
occurred.
The tyre has two or more
punctures.
Using the Puncture Tyre Repair
Kit
1. Move the vehicle off the right-of-way
to a safe place on a level and hard
surface where the vehicle does not
obstruct traffi c.
2. Shift the shift lever to the 1 or Reverse
(R) position for a manual transaxle, and
shift the selector lever to the P position
for an automatic transaxle.
3. Apply the parking brake with the brake
pedal depressed and turn off the engine.
4. If necessary, fl ash the hazard warning
lights and set up the roadside
emergency triangle.
5. Unload passengers and cargo and
remove the puncture tyre repair kit.
Saloon
Hatchback
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 588 of 689
7–12
If Trouble Arises
Flat Tyre
WARNING
Never use the air compressor above 300
kPa (3.1 kgf/cm 2 , 3 bar, 43.5 psi):
Using the air compressor at an
infl ation pressure above 300 kPa (3.1
kgf/cm
2 , 3 bar, 43.5 psi) continuously
is dangerous. If the air compressor
overheats, hot air will be exhausted and
you could get burned.
CAUTION
If the air compressor operates slowly or
becomes hot, this indicates overheating.
Turn the air compressor OFF
immediately and cancel the procedure.
In this case, leave the air compressor
turned OFF for about 30 minutes or
longer and wait until the temperature
decreases.
NOTE
Check the tyre infl ation pressure
label (driver's door frame) for the
correct tyre infl ation pressure.
Do not operate the air compressor for
a continuous 10 minutes or longer
because using it for long periods
could cause a malfunction.
If the tyre infl ation pressure does
not increase, repair of the tyre is not
possible. If the tyre does not reach
the specifi ed tyre infl ation pressure
within 10 minutes, it may have
received extensive damage. In this
case, the repair using the emergency
fl at tyre repair kit was not successful.
Contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
13. Adhere the speed restriction sticker to
an area where it can be viewed easily
by the driver.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 589 of 689
7–13
If Trouble Arises
Flat Tyre
WARNING
Do not adhere the speed restriction
sticker to the padded area on the
steering wheel:
Adhering the speed restriction sticker
to the padded area on the steering
wheel is dangerous because the air
bag may not operate (deploy) normally
resulting in serious injury. In addition,
do not adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
14. When the tyre infl ates to the specifi ed
tyre infl ation pressure, turn the air
compressor switch OFF, turn the sleeve
of the injection hose to the left, and pull
it out of the tyre valve. Turn the sleeve
of the injection hose to the left, and pull
it out of the tyre valve.
15. Remove the compressor hose from the
injection valve of the bottle. After that,
install the injection hose to the injection
valve of the bottle to prevent leakage of
any remaining sealant.
CAUTION
The remaining sealant in the hose may
spray out when the hose is removed.
Remove the hose carefully because you
may not be able to remove the sealant
contacting clothing or other objects.
16. Install the tyre valve cap.
17. Put the puncture tyre repair kit into the
boot/luggage compartment.
18. Start driving immediately to spread the
sealant in the tyre.
CAUTION
Carefully drive the vehicle at a speed of
80 km/h (50 mph) or less. If the vehicle
is driven at a speed of 80 km/h (50 mph)
or more, the vehicle may vibrate.
NOTE
(With Tyre Pressure Monitoring
System)
If the tyre is not properly infl ated, the
tyre pressure monitoring system warning
light will illuminate (page 4-40 ).
19. After driving the vehicle for about 10
minutes or 5 km (3 miles), connect
the air compressor to the tyre using
Step 9 of the procedure, and check the
tyre infl ation pressure using the tyre
pressure gauge on the air compressor. If
the tyre infl ation pressure is lower than
the specifi ed tyre infl ation pressure,
turn the air compressor ON and wait
until it reaches the specifi ed tyre
infl ation pressure.
. B [ E B @ & ' & & " @ & E J U J P O J O E C