ECO mode MAZDA MODEL 3 HATCHBACK 2016 (in English) Owner's Manual

4–36
When Driving
Transaxle
Shift gear (shifting) speed limit
For each gear position while in the manual mode, the speed limit is set as follows: When the
selector lever is operated within the range of the speed limit, the gear is shifted.



Shift up
The gear does not shift up while the vehicle speed is lower than the speed limit.
Shift down
The gear does not shift down while the vehicle speed exceeds the speed limit.
If the vehicle speed exceeds the speed limit and the gear does not shift down, the gear
position indication À ashes 2 times to notify the driver that the gear cannot be shifted.
Kickdown
When the accelerator pedal is depressed fully while driving, the gear shifts down.
N O T E
The gear also shifts down using kickdown while in the second gear ¿ xed mode.
Auto-shift down
The gear shifts down automatically depending on the vehicle speed during deceleration.
N O T E
If the vehicle comes to a stop while in the second gear ¿ xed mode, the gear remains in
second.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–38
When Driving
Transaxle
*Some models.
Direct Mode *
Direct mode can be used for temporarily
switching gears by operating the steering
shift switch while the vehicle is being
driven with the selector lever in the D
range.
While in direct mode, the D and M
indication illuminate and the gear position
in use is illuminated.
Direct mode is canceled (released) under
the following conditions.

 


y The UP switch ( ) is pulled
rearward for a certain amount of time or
longer.
 


y The vehicle is driven for a certain
amount of time or longer (time differs
depending on the driving conditions
while operating).
 


y The vehicle is stopped or moving at a
slow speed.


Ty p e A


Gear position indication
Direct mode indication
Ty p e B


Gear position indication
Direct mode indication

Ty p e C


Gear position indication
Direct mode indication

N O T E
Shifting up and down while in direct mode
may not be possible depending on the
vehicle speed. In addition, because direct
mode is canceled (released) depending
on the rate of acceleration or if the
accelerator is fully depressed, use of the
manual shift mode is recommended if you
need to drive the vehicle in a particular
gear for long periods.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–42
When Driving
Switches and Controls
Auto-light control
When the headlight switch is in the
position and the ignition is switched ON, the light
sensor senses the surrounding lightness or darkness and automatically turns the headlights,
other exterior lights and dashboard illumination on or off (see chart above).
CAUTION
 


¾ Do not shade the light sensor by adhering a sticker or a label on the windshield. Otherwise
the light sensor will not operate correctly.
 

 


¾ The light sensor also works as a rain sensor for the auto-wiper control. Keep hands and
scrapers clear of the windshield when the wiper lever is in the
position and the
ignition is switched ON as fi ngers could be pinched or the wipers and wiper blades could be
damaged when the wipers activate automatically. If you are going to clean the windshield,
be sure the wipers are turned off completely when it is particularly tempting to leave the
engine running. This is particularly important when clearing ice and snow.

N O T E
 


y The headlights, other exterior lights and dashboard illumination may not turn off
immediately even if the surrounding area becomes well-lit because the light sensor
determines that it is night time if the surrounding area is continuously dark for several
minutes such as inside long tunnels, traf¿ c jams inside tunnels, or in indoor parking lots.

 In this case, the lights turn off if the light switch is turned to the position.



y (Without auto headlight off function) 
 When the headlight switch is in the position and the ignition is switched to ACC or
the ignition is switched off, the headlights, other exterior lights and dashboard
illumination will turn off.
 


y The dashboard illumination can be adjusted by rotating the knob in the instrument cluster.
Also, the day/night mode can be changed by rotating the knob until a beep sound is heard.
To adjust the brightness of the dashboard illumination:
  Refer to Dashboard Illumination on page 4-15 .



y The sensitivity of the AUTO lights may be changed by an Authorized Mazda Dealer.
 Refer to Personalization Features on page 9-12 .
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–69
When Driving
Fuel Economy Monitor
*Some models.
Fuel Economy Monitor *
For vehicles with type B audio, the Control Status and Fuel Consumption are switched and
displayed by operating each icon in the display.
In addition, after completing a trip, the total energy ef¿ ciency to date is displayed in the
ending display when the ending display is turned on.

1. Select the icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Operate the commander switch or touch the screen and display the menu.
N O T E
When the menu is displayed by touching the screen, the display is hidden automatically after
6 seconds.

4. Select the icon in the menu and perform the operation. Each icon operates as follows:

Indication on display Control status

Hides the menu display.

Displays the application screen.

Switches the Fuel Economy Monitor in the order of
Control Status and Fuel Consumption.

Resets the fuel economy data.

Displays the following setting screen.
y Ending display on/off switching
y On/off switching for function which synchronizes
reset fuel economy data to trip meter (Trip A)

Fuel Consumption Display
Information regarding the fuel economy is displayed.

Indication on display Control status

Displays the fuel economy for the past 60 minutes.
y Displays the fuel economy every minute for the
past 1 to 10 minutes.

y Displays the fuel economy every 10 minutes for the
past 10 to 60 minutes.

Displays the average fuel economy over the past 5
resets and after the current reset.

Calculates the average fuel economy every minute
after vehicle travel begins, and displays it.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–71
When Driving
Drive Selection
*Some models.
Drive Selection *
Drive selection is a system to switch the vehicle's drive mode. When the sport mode
is selected, vehicle's response against accelerator operation is enhanced. This provides
additional quick acceleration which may be needed to safely make maneuvers such as lane
changes, merging onto freeways, or passing other vehicles.
CAUTION
Do not use the sport mode when driving on slippery roads such as wet or snow-covered
roads. It may cause tire slipping.

N O T E
 


y When the sport mode is selected, driving at higher engine speeds increases and it may
increase fuel consumption. Mazda recommends that you cancel the sport mode on normal
driving.
 


y Drive mode cannot be switched in the following conditions: 



y ABS/TCS/DSC is operating



y The Mazda Radar Cruise Control (MRCC) system/cruise control is operating.



y Steering wheel is being operated abruptly

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










5–16
Interior Features
Audio System
*Some models.
A n t e n n a
Antenna (4-Door)
AM/FM Radio Antenna
The AM/FM radio antenna receives both
AM and FM signals.
The antenna is embedded into the window
glass.
CAUTION
When washing the inside of the
window which has an antenna, use
a soft cloth dampened in lukewarm
water, gently wiping the antenna lines.
Use of glass cleaning products could
damage the antenna.

Satellite Radio Antenna *
The satellite radio antenna receives
SiriusXM signals.

Antenna

Antenna (5-Door)
AM/FM Radio Antenna *
The AM/FM radio antenna receives both
AM and FM signals.
(Type A)
To remove the antenna, turn it
counterclockwise.
To install the antenna, turn it clockwise.
Make sure the antenna is securely
installed.


RemoveInstall

CAUTION
 


¾ To prevent damage to the antenna,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
 


¾ Be careful around the antenna when
removing snow from the roof. Otherwise
the antenna could be damaged.

N O T E
When leaving your vehicle unattended, we
recommend that you remove the antenna
and store it inside the vehicle.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










5–24
Interior Features
Audio System
N O T E
 


y Playback may not be possible
depending on the type and condition of
the USB À ash memory even if the audio
¿ le complies with the standard above.




y A copyright protected WMA/AAC ¿ le
cannot be played in this unit.
 


y The order of the music data stored in
the device may differ from the playback
order.
 


y To prevent loss or damage of stored
data, we recommend that you always
back up your data.
 


y If a device exceeds the maximum
electric current value of 1,000 mA,
it may not operate or recharge when
connected.
 


y Do not pull out the USB device while in
the USB mode (only pull it out while in
FM/AM radio or CD mode).
 


y The device will not operate if the data is
password protected.

MP3/WMA/AAC/OGG *1 ¿ les written
under speci¿ cations other than the
indicated speci¿ cation may not play
normally or ¿ les/folder names may not
display correctly.

*1 Type B
Operating Tips for iPod
This unit supports playback of music ¿ les
recorded to an iPod.

 

*
 iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries.

The iPod may not be compatible
depending on the model or OS version. In
this case, an error message is displayed.
CAUTION
 


¾ Remove the iPod when it is not in
use. Because the iPod is not designed
to withstand excessive changes in
temperature inside the cabin, it could be
damaged or the battery may deteriorate
due to the excessive temperature or
humidity inside the cabin if it is left in the
vehicle.
 


¾ If data in the iPod is lost while it is
connected to the unit, Mazda cannot
guarantee recovery of any lost data.
 


¾ If the iPod battery is deteriorated, the
iPod may not recharge and playback
may not be possible when it is connected
to the unit.
 


¾ Be careful not to pinch the iPod
connecting cable when opening/closing
the center console.
 


¾ For details on using the iPod, refer to the
iPod instruction manual.
 


¾ When connecting the iPod to a USB port,
all commands are made from the audio
unit. iPod control is not possible.

N O T E
The audio unit cannot display images or
videos stored in an iPod.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










5–27
Interior Features
Audio System
*Some models.
N O T E
If not operated for several seconds, the
display returns to the previous display. To
reset bass, treble, fade, and balance, press
the menu button (
) for 2 seconds.
The unit will beep and “ CLEAR ” will be
displayed.

ALC (Automatic volume adjustment)
The automatic level control (ALC)
changes the audio volume automatically
according to the vehicle speed. The faster
the vehicle speed, the higher the volume
increases. ALC has ALC OFF and ALC
LEVEL 1 to 7 modes. At ALC LEVEL 7,
the amount that the volume can increase
is at the maximum. Select the mode
according to the driving conditions.
BEEP (Audio operation sound)
The setting for the operation sound when
pressing and holding a button can be
changed. The initial setting is ON. Set to
OFF to mute the operation sound.
BT SETUP mode
*
Music and other audio such as voice data
recorded on portable audio devices and
mobile phones available on the market
which are equipped with the Bluetooth
®
transmission function can be listened to
via wireless transmission over the vehicle's
speakers. Using the BT SETUP mode,
these devices can be programmed to the
Bluetooth
® unit or changed (page 5-80 ).
1 2 H r
24Hr (12 Hr/24 Hr time
adjustment)
Rotating the audio control dial switches
the display between 12 and 24-hour clock
time (page 5-28 ).
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










5–30
Interior Features
Audio System
Operating the Radio
Band selector buttonChannel preset buttons
Scan button
Auto memory button
Tuning buttonAudio display

R a d i o O N
Press a band selector button (
) to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1
:FM2
:AM.

The selected mode will be indicated.
N O T E
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise.

Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Select the station by pressing the tuning
button (
, ) lightly. Seek tuning
Automatic search for radio stations starts
when the tuning button (
, ) is pressed
until a beep sound is heard. The search
stops when a station is found.
N O T E
If you continue to press and hold the
button, the frequency will continue
changing without stopping.

Scan tuning
Press and hold the scan button (
) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, press and hold
the scan button (
) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.

1. To set a channel ¿ rst select AM, FM1,
or FM2. Tune to the desired station.
2. Press a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number or station
frequency will be displayed. The
station is now held in the memory.
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










5–32
Interior Features
Audio System
*Some models.
Operating the Compact Disc (CD) Player *

CD eject button CD slotMedia/Scan buttonFolder down button Folder up button Play/Pause button
Random button Repeat button
Audio display Text button
Track down/
Reverse button
Track up/
Fast-forward button

Type Playable data
Music/MP3/WMA/
AAC CD player
y Music data (CD-DA)
y MP3/WMA/AAC ¿ le

N O T E
If a disc has both music data (CD-DA)
and MP3/WMA/AAC ¿ les, playback of the
two or three ¿ le types differs depending on
how the disc was recorded.

Inserting the CD
Insert the CD into the slot, label-side up.
The auto-loading mechanism will set the
CD and begin play.
N O T E
There will be a short lapse before play
begins while the player reads the digital
signals on the CD.

Ejecting the CD
Press the CD eject button (
) to eject the
CD.
Playback
Press the media button (
) to switch
to CD mode and start playback.
N O T E
The CD mode cannot be selected if a CD
has not been inserted.

Pause
To stop playback, press the Play/Pause
button ( 4 ).
Press the button again to resume playback.
Fast-forward/Reverse
Press and hold the fast-forward button (
)
to advance through a track at high speed.
Press and hold the reverse button (
) to
reverse through a track at high speed.
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC