ignition MAZDA MODEL 6 2004 (in English) Workshop Manual

6-37
Interior Comfort
Au d i o S y s t e m
Form No. 8R29-EA-02I
Multiple insertion
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. When "In" is displayed, insert the CD.
3. When "In" is displayed again, insert
the next CD.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The disc
number and "DISC OUT" will be
displayed.
2. Pull out the CD.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 5 seconds
after the beep is heard.
3. Pull out the CD.Multiple ejection
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Wait 5 seconds or press the CD eject
button ( ) again within 5 seconds after
the beep is heard.
3. Pull out the CD, then the next CD will
be ejected.
NOTE
The first-inserted CD will be played
automatically when:
•
No CD is inserted within 15
seconds after "In" is displayed.
•
The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•
CDs will be ejected starting with the
one with the lowest number.
•
All CDs in the tray will be ejected
continuously.
•
CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
shuseizumi_J56J_8R29_EA_02I.book Page 37 Saturday, September 7, 2002 12:58 PM

6-43
Interior Comfort
Form No. 8R29-EA-02I
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Vanity Mirrors
To use the vanity mirror, lower the
sunvisor.
If your vehicle is equipped with a vanity
mirror light, it will illuminate when you
pull the cover up.

Illuminated Entry System
When the switch is in the DOOR position,
the overhead light and the courtesy lights
come on for:
•
About 30 seconds after the driver’s
door is unlocked and the ignition key is
removed.
•
About 15 seconds after all doors are
closed.
•
About 15 seconds after the key is
removed from the ignition with all
doors closed.
The light also goes out when:
•
The ignition switch is turned to the ON
position and all doors are closed.
•
The driver’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
The light turns on again when the
ignition switch is turned to the ON
position, or when any door is opened
after all doors have been closed.
shuseizumi_J56J_8R29_EA_02I.book Page 43 Saturday, September 7, 2002 12:58 PM

6-47
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I

Clock
When the ignition switch is in the ACC or
ON position, the time is displayed.
Time setting
1. Press the CLOCK button until a beep
sounds, and "12Hr" and "24Hr" will be
displayed.
2. Press the SET button to switch between
"12Hr" and "24Hr" displays. The
selected display will flash.
To select the desired clock setting,
press the CLOCK button again while
the preferred setting is flashing.
3. "Hr. ADJUST" will be displayed next,
and the hour portion of the display will
flash. Press the SET button to set the
hour, then press the CLOCK button.
4. "Min. ADJUST" will be displayed
next, and the minutes portion of the
display will flash. Press the SET button
to set the minutes, then press the
CLOCK button.Time resetting
While the clock is displayed, press the
SET button 1.5 seconds or more. When
the button is released, a beep will sound
and the clock will be reset as follows:
(Example)
12:01—12:29→
12:00
12:30—12:59→
1:00
NOTE
When the SET button is released, the
seconds are reset to "00".
shuseizumi_J56J_8R29_EA_02I.book Page 47 Saturday, September 7, 2002 12:58 PM

6-48
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I

Ambient Temperature Display
When the ignition switch is in the ON
position, press the AMB button to display
the ambient temperature.

Climate Control Display
Climate control is displayed when the
climate control system is turned on (page
6-5).

Audio Display
Audio is displayed when the audio system
is turned on (page 6-23).

Display Dimmer Cancel Function
When driving at night on snowy or foggy
roads, or in other situations when the
display’s visibility is reduced due to glare
from surrounding brightness, the display
dimmer cancel function increases the
intensity of the display illumination.
The display dimmer cancel function can
be used when the headlight switch is in
the or position.
Press the DIMMER button to increase the
intensity of the display illumination.
Press the button again to return to the
previous display illumination.
NOTE
•
The displayed ambient temperature
may vary from the actual ambient
temperature depending on the
surrounding area and vehicle
conditions.
•
Press the AMB button again to
switch the display from ambient
temperature to the temperature set
for the air conditioner.
•
Press the AMB button 1.5 seconds
or more to switch the display from
Fahrenheit to Centigrade or vice
versa.
shuseizumi_J56J_8R29_EA_02I.book Page 48 Saturday, September 7, 2002 12:58 PM

6-49
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I
The ignition switch must be in the ACC or
ON position.
1. Open the cover.
2. Press the lighter in and release it. When
ready for use, it automatically pops out.
Lighter
•
Don’t touch the metal part of the
lighter, you may burn yourself.
•
Don’t hold the lighter in because it
will overheat.
•
Don’t use the lighter socket for
plug-in accessories such as shavers
and coffee pots. They may damage
it or cause electrical failure. Use
only a genuine Mazda lighter or the
equivalent.
•
If the lighter doesn’t pop out within
30 seconds, remove it to prevent
overheating.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 49 Saturday, September 7, 2002 12:58 PM

6-54
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I
The ignition switch must be in the ACC or
ON position.
Only use genuine Mazda accessories or
the equivalent requiring no greater than
120 W (DC12 V, 10 A).When placing an electrical device (e.g.
cellular phone) in the tray which is
connected with the accessory socket, pass
the plug cord through the slot in the cap.
1. Open the lid by pulling the upper
release catch.
2. Remove the tray mat.
3. Using a coin, turn the cap
counterclockwise (about 45°
from the
closed position) and remove it.
4. Open the tray by pulling the lower
release catch.
Accessory Socket
To prevent accessory socket damage or
electrical failure, pay attention to the
following;
•
Don’t use accessories that require
more than 120 W (DC12 V, 10 A).
•
Don’t use accessories that are not
genuine Mazda accessories or the
equivalent.
•
Close the cover when the accessory
socket is not in use.
•
Correctly insert the plug into the
accessory socket.
NOTE
To prevent discharging the battery,
don’t use the socket for long periods
with the engine off or idling.
CAUTION
Cap slot, closed
Cap slot, opened
shuseizumi_J56J_8R29_EA_02I.book Page 54 Saturday, September 7, 2002 12:58 PM

7-12
In Case of an Emergency
Form No. 8R29-EA-02I
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
Apply the parking brake.
3. Turn off the air conditioner.4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:Don’t go near the front of the vehicle.
Stop the engine. Then turn the ignition
switch to the ON position without
starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping:Open the hood and idle the engine until
it cools. If this doesn’t lower the
temperature, stop the engine and let it
cool.
Overheating
Steam from Overheated Engine:Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 12 Saturday, September 7, 2002 12:58 PM

7-14
In Case of an Emergency
Form No. 8R29-EA-02I
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and
hold it there.
2. Turn the ignition switch to the START
position and hold it there—for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it
without using the accelerator—for up
to 10 seconds.Jump-starting is dangerous if done
incorrectly. So follow the procedure
carefully. If you feel unsure about jump-
starting, we strongly recommend that you
have a competent service technician do
the work.
Starting a Flooded EngineJump-Starting
Battery-Related Explosion:Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from
open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one
with a low fluid level is dangerous. It
may rupture or explode, causing
serious injury.
Don’t jump-start a frozen battery or
one with a low fluid level.
Use only a 12 V booster system. You
can damage a 12 V starter, ignition
system, and other electrical parts
beyond repair with a 24 V power
supply (two 12 V batteries in series or
a 24 V motor generator set).
WARNING
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 14 Saturday, September 7, 2002 12:58 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8R29-EA-02I

Schedule 1
I: Inspect and repair, clean, adjust, or replace if necessary.
R: Replace
L: Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if installed)
*1According to state/provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage/kilometer period to ensure long-term reliability. Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Drive belts (tension) 2.3-liter engine
I
3.0-liter engine
II
Engine oil
RRRRRRRR
Engine oil filter
RRRRRRRR
Cooling system
II
Engine coolantReplace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Air filter
R
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugs
Replace every 120,000km (75,000miles)
Brake lines, hoses and connections
II
Disc brakes
IIII
Steering operation and linkages
II
Front suspension ball joints
II
Driveshaft dust boots
II
Bolts and nuts on chassis and body
II
Exhaust system heat shields
II
All locks and hinges
LLLLLLLL
Cabin air filter
Replace every 40,000km (25,000miles) or 24 months
shuseizumi_J56J_8R29_EA_02I.book Page 4 Saturday, September 7, 2002 12:58 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8R29-EA-02I

Schedule 2
I: Inspect and repair, clean, adjust, or replace if necessary.
R:Replace
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
ELECTRICAL SYSTEM
*1According to state/provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage/kilometer period to ensure long-term reliability.
*2If the vehicle is operated under any of the following conditions, change the spark plugs every 96,000
km(60,000 miles) or shorter.
a)Repeated short-distance driving
b)Extended periods of idling or low-speed operation
c)Driving for long periods in cold temperatures or extremely humid climates
Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Drive belts (tension) 2.3-liter engine
I
3.0-liter engine
II
Engine oilPuerto Rico
Replace every 5,000km (3,000miles) or 3 months
Others
RRRRRRRRRRRR
Engine oil filter
RRRRRRRRRRRR
Cooling system
II
Engine coolantReplace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level
IIIIIIIIIIII
Air filterPuerto Rico
R
Others
R
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugs USA
Replace every 96,000km (60,000miles)
Others
*2Replace every 120,000km (75,000miles)
Function of all lights
IIIIIIIIIIII
shuseizumi_J56J_8R29_EA_02I.book Page 5 Saturday, September 7, 2002 12:58 PM