garage door opener MAZDA MODEL 6 2004 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2004, Model line: MODEL 6, Model: MAZDA MODEL 6 2004Pages: 289, PDF Size: 7.22 MB
Page 142 of 289
5-43
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
The HomeLink system replaces up to 3
hand-held transmitters with a single built-
in component in the auto-dimming mirror.
Pressing the HomeLink button on the
auto-dimming mirror activates garage
doors, gates and other devices
surrounding your home.
HomeLink Wireless
Control System
HomeLink buttonIndicator light
Safety Stop and Reverse Feature:Using the HomeLink system with any
garage door opener that lacks the
safety stop and reverse feature as
required by federal safety standards is
dangerous. (This includes garage
doors manufactured before April 1,
1982.)
Using these garage door openers can
increase the risk of serious injury or
death. Call Johnson Controls, Inc.
number: 1.800.355.3515 or visit
www.homelink.com for further
information. If you are unable to
make contact with Johnson Controls,
Inc., consult an Authorized Mazda
Dealer.
Safety While Programming or
Operating HomeLink System:Programming or operating the
HomeLink system without verifying
the safety of areas surrounding
garage doors and gates is dangerous
and could result in an unexpected
accident and serious injury if
someone were to be hit. Always check
the areas surrounding garage doors
and gates for people or obstructions
before programming or during
operation of the HomeLink system.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 43 Saturday, September 7, 2002 12:58 PM
Page 143 of 289
5-44
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
Programming the HomeLink
System
The HomeLink system provides 3 buttons
which can be individually selected and
programmed using the transmitters for
current, on-market devices as follows:
1. Verify that there is a remote control
transmitter available for the device you
would like to program.
2. Disconnect the power to the device.
3. Hold the transmitter for the device to
be programmed in close proximity to
HomeLink, approximately 2.5—7.5
cm (1—3 in).
4. Press the transmitter button and the
desired HomeLink button
simultaneously until the HomeLink
indicator light goes from slow to rapid
flashing.
5. Connect the power to the device.
6. Verify that the device operates properly
by pressing the HomeLink button that
was programmed. The transceiver has been tested and
complies with FCC and Industry
Canada rules. Changes or
modifications not expressly approved
by the party responsible for
compliance could void the user’s
authority to operate the device.NOTE
FCC ID: NZLSTDHL3
CANADA: 4112104541A
This device complies with FCC rules
part 15. Operation is subject to the
following conditions:
1- This device may not cause any
harmful interference and
2- This device must accept any
interference that may be received
including interference that may cause
undesired operation.
NOTE
The programming will not be erased
even if the battery is disconnected.
CAUTION
When programming a garage door
opener or a gate, disconnect the power
to these devices before performing
programming, as continuous operation
of the devices could damage the motor.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 44 Saturday, September 7, 2002 12:58 PM
Page 144 of 289
5-45
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
Reprogramming the HomeLink
system
To reprogram a single HomeLink button,
perform the procedure for programming
the HomeLink system (page 5-44).
The previous code will be erased and
replaced by the new code.
Rolling Code Synchronization
Look in your garage door opener or other
device instruction manual to see if your
system is equipped with a rolling code
feature for synchronizing rolling code-
equipped devices.
For synchronizing rolling code-equipped
devices, perform the following procedure
after finishing the HomeLink system
programming (page 5-44). The procedure
will take less time with a second person to
help.
1. Press the programming button on the
garage door opener motor head unit.
Refer to the device’s instruction
manual to locate the programming
button.2. Press and release the programmed
HomeLink button 2 times within 30
seconds of pressing the programming
button. (Some devices may require you
to press and release a third time to
complete the programming.)
Perform the above procedure for any other
rolling code-equipped devices.
Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.
Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons ( , )
on the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 20 seconds.
Verify that the programming has been
erased when you resell the vehicle.
NOTE
Canadian Owners:
Some Canadian transmitters stop
transmitting after 2 seconds.
Repeatedly press the transmitter button
every 2 seconds until HomeLink stores
the code (until the HomeLink indicator
light flashes rapidly).
shuseizumi_J56J_8R29_EA_02I.book Page 45 Saturday, September 7, 2002 12:58 PM