lock MAZDA MODEL 6 HATCHBACK 2004 Owners Manual (in English)

Black plate (264,1)
NOTE
To prevent damage to the wiper arm
blades when raising both the driver and
passenger side wiper arms, raise the
driver side wiper arm first. Conversely,
when setting down the wiper arms, set
the passenger side wiper arm down
first.
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip Push
CAUTION
To prevent damage to the windshield,
don't let the wiper arm fall on it.2. Hold the end of the rubber and pull
until the tabs are free of the metal
support.
Metal support
Pull out Ta b
3. Remove the metal stiffeners from the
blade rubber and install them in new
blades.
Stiffeners
8-22
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page264
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (265,1)
CAUTION
lDon't bend or discard the stiffeners.
You need to use them again.
lIf the metal stiffeners are switched,
the blade's wiping efficiency could
be reduced.
So don't use the driver's side metal
stiffeners on the passenger's side, or
vice versa.
lBe sure to reinstall the metal
stiffeners in the new blade rubber so
that the curve is the same as it was in
the old blade rubber.
4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
Ta b
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
qReplacing Rear Window Wiper
Blade (Hatchback/Wagon)
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, don't move the
wiper by hand.
(Hatchback)
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clipPush
CAUTION
To prevent damage to the rear window,
don't let the wiper arm fall on it.
Maintenance and Care
Owner Maintenance
8-23
Mazda6_8T12-EA-03K_Edition1 Page265
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (266,1)
2. Hold the end of the blade rubber and
pull until the tabs are free of the metal
support.
Metal support
Pull out Ta b
3. Remove the metal stiffeners from the
blade rubber and install them in new
blades.
Stiffeners
CAUTION
Don't bend or discard the stiffeners.
You need to use them again.4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
(Wagon)
1. Raise the wiper arm and rotate the
wiper blade to the right until it unlocks,
then remove the blade.
CAUTION
To prevent damage to the rear window,
don't let the wiper arm fall on it.
8-24
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page266
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (274,1)
Your Mazda's headlights and fog lights
have replaceable halogen bulbs.
WARNING
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries could
be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
qReplacing Exterior Light Bulbs
Replacing the headlight, fog light andparking light bulbs
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Front turn signal lights
1. Turn the socket and bulb assembly
counterclockwise and remove it.2. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
Socket
3. Install the new bulb in the reverse order
of removal.
Side-marker lights
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
8-32
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page274
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (275,1)
3. Disconnect the bulb from the socket.
Socket
Brake lights/Taillights, Rear turn signallights
(Sedan)
1. Pull the center section of the plastic
retainer and remove the retainers and
partially open the trunk side trim.
Trunk side trim
Removal
Installation
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
Socket
Rear turn signal lights
Brake lights/Taillights
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
(Hatchback)
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
(Wagon)
1. Turn the knob and remove the cover.
Left side
Right side
2. Turn the socket and bulb assembly
counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-33
Mazda6_8T12-EA-03K_Edition1 Page275
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (276,1)
3. Disconnect the bulb from the socket.
Socket
Rear turn signal lights
Brake lights/Taillights
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Reverse lights, Taillights
(Sedan)
1. Pull the center section of the plastic
retainer and remove the retainers, then
remove the trunk rear trim.
Trunk rear trim Installation Removal
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
Reverse lights
Taillights
Socket
4. Install the new bulb in the reverse order
of removal.
(Hatchback/Wagon)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Reverse lights
Taillights
Socket
4. Install the new bulb in the reverse order
of removal.
High-mount brake light
(Sedan)
1. Remove the high-mount brake light
component.
8-34
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page276
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (277,1)
2. Detach the electrical connector from
the socket.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
Socket
5. Install the new bulb in the reverse order
of removal.
(Hatchback)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Socket
4. Install the new bulb in the reverse order
of removal.(Wagon)
1. Remove the liftgate upper trim and
high-mount brake light component.
Liftgate upper trim
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Socket
4. Install the new bulb in the reverse order
of removal.
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens.
Maintenance and Care
Owner Maintenance
8-35
Mazda6_8T12-EA-03K_Edition1 Page277
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (278,1)
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Withoverhead console)
1. Remove the screws.
2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.4. Disconnect the bulb from the socket.
Socket
5. Install the new bulb in the reverse order
of removal.
Overhead light/Map lights (Withoutoverhead console)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
8-36
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page278
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (281,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
Fuse puller
Engine compartment fuse box
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the SPARE circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
Fuse block cover
Tab
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-40).
Maintenance and Care
Owner Maintenance
8-39
Mazda6_8T12-EA-03K_Edition1 Page281
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (282,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
1 SPARE 20A—
2 SPARE 15A—
3 SPARE 10A—
4—— —
5—— —
6 INJ 15A Injector
7ENG
BAR10A
*1Air flow sensor, EGR control
valve
15A*2
8ENG
BAR2*115A O2 sensor
ENG
BB
*25A Cooling fan
9HEAD
LR10A Headlight-low beam (Right)
10HEAD
LL10A Headlight-low beam (Left)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
11HEAD
HL10A Headlight-high beam (Left)
12HEAD
HR10A Headlight-high beam (Right)
13ETC 7.5A Accelerator position sensor
14 HAZARD10A Turn signal lights
15STOP 15A Brake/Taillights
16TCM*110A TCM
IG1*215A O2 sensor
17 ENGB7.5A PCM, TCM
18FUEL
PUMP15A Fuel pump
19IG KEY 40AWindshield wiper and washer,
Engine control unit, Lighter
20P.WIND 30A Power window
21—— —
22—— —
8-40
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page282
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K