washer fluid MAZDA MODEL 6 HATCHBACK 2004 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2004, Model line: MODEL 6 HATCHBACK, Model: MAZDA MODEL 6 HATCHBACK 2004Pages: 326, PDF Size: 3.96 MB
Page 110 of 326

Black plate (110,1)
Before Getting In
lBe sure the windows, outside mirrors,
and outside lights are clean.
lInspect inflation pressures and
condition of tires.
lLook under the vehicle for any sign of
a leak.
lIf you plan to back up, make sure
nothing will be in your way.
NOTE
Engine oil, engine coolant, brake/clutch
fluid, washer fluid, and other fluid
levels should be inspected. See
Maintenance, Section 8.
After Getting In
lAre all doors closed and locked?
lIs the seat adjusted properly?
lAre the inside and outside mirrors
adjusted?
lIs everyone's seat belt fastened?
lCheck all gauges.
lCheck all warning lights when the
ignition switch is turned to the ON
position.
lRelease the parking brake and make
sure the brake warning light goes off.
Always be thoroughly familiar with your
Mazda.
4-6
Before Driving Your Mazda
Before Starting the Engine
Mazda6_8T12-EA-03K_Edition1 Page110
Friday, December 5 2003 8:55 AM
Form No.8T12-EA-03K
Page 113 of 326

Black plate (113,1)
Winter Driving
lCarry emergency gear, window
scraper, flares, a small shovel, jumper
cables, and a small bag of sand or salt.
Ask an Authorized Mazda Dealer to
perform the following precautions:
lHave the proper ratio of antifreeze in
the radiator.
lInspect the battery and its cables. Cold
reduces battery capacity.
lInspect the ignition system for damage
and loose connections.
lUse washer fluid made with antifreeze
—but don't use engine coolant
antifreeze for washer fluid (page 8-18).
lDon't use the parking brake in freezing
weather as the parking brake may
freeze. Instead, shift to P with an
automatic transaxle and to 1 or R with
a manual transaxle. Block the rear
wheels.
qSnow Tires
WARNING
Mixing Tire Types:
Using tires different in size or type is
dangerous. Your vehicle's handling
could be greatly affected and result in
an accident. Use only the same size
and type tires (snow, radial, or non-
radial) on all four wheels.
CAUTION
Check local regulations before using
studded tires.
Use snow tires on all four wheels
Don't go faster than 120 km/h (75 mph)
while driving with snow tires. Inflate
snow tires 30 kPa (0.3 kgf/cm
2, 4.3 psi)
more than recommended on the tire
pressure label (driver's door frame), but
never more than the maximum cold-tire
pressure shown on the tires.
Your vehicle is originally equipped with
all season radials designed to be used all
year around. In some extreme climates
you may find it necessary to replace them
with snow tires during the winter months
to further improve traction on snow and
ice covered roads.
qTire Chains
This vehicle cannot be operated with tire
chains because it could cause interference
with the vehicle body and scratching.
Before Driving Your Mazda
Driving Tips
4-9
Mazda6_8T12-EA-03K_Edition1 Page113
Friday, December 5 2003 8:55 AM
Form No.8T12-EA-03K
Page 145 of 326

Black plate (145,1)
Signal Warning/Indicator Lights Page
Seat Belt Warning Light 5-33
Door-Ajar Warning Light 5-33
Low Washer Fluid Level Warning Light 5-33
Automatic Transaxle Warning Light 5-34
Security Indicator Light 5-34
Headlight High-Beam Indicator Light 5-34
Shift Position Indicator Light 5-35
TCS Indicator Light 5-35
TCS OFF Indicator Light 5-35
Cruise Main Indicator Light 5-36
Cruise Set Indicator Light 5-36
Light-On Indicator Light 5-36
Turn-Signal/Hazard Warning Indicator Lights 5-36
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-29
Mazda6_8T12-EA-03K_Edition1 Page145
Friday, December 5 2003 8:56 AM
Form No.8T12-EA-03K
Page 149 of 326

Black plate (149,1)
A system malfunction is indicated when
the warning light constantly flashes,
illuminates or doesn't illuminate at all
when the ignition switch is turned to the
ON position. If any of these occur, consult
an Authorized Mazda Dealer as soon as
possible. The system may not work in an
accident.
WARNING
Self-Servicing the Air Bag/Pretensioner Systems:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled. This
could cause serious injuries. Never
tamper with the systems and always
have an Authorized Mazda Dealer
performs all servicing and repairs.
qLow Fuel Warning Light
Low fuel
warning light
This warning light in the fuel gauge
signals that the fuel tank will soon be
empty.
Refuel as soon as possible.
qSeat Belt Warning Light
If the driver's seat belt is not fastened
when the ignition switch is turned to the
ON position, the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.
qDoor-Ajar Warning Light
This warning light comes on when any
door isn't securely closed.
qLow Washer Fluid Level
Warning Lightí
This warning light indicates that little
washer fluid remains. Add fluid (page
8-18).
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-33íSome models. Mazda6_8T12-EA-03K_Edition1 Page149
Friday, December 5 2003 8:56 AM
Form No.8T12-EA-03K
Page 156 of 326

Black plate (156,1)
Fog Lightsí
Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn the front fog lights on, rotate the
fog light switch to the
position.
The headlight switch must be in the
position to turn on the front fog lights.
OFF
Fog light switch
To turn them off, rotate the fog light
switch to the OFF position or turn the
headlight switch to the
or OFF position.
NOTE
The fog lights will turn off when the
headlights are set at high beam.
Windshield Wipers and
Washer
The ignition switch must be in the ON
position.
WARNING
Frozen Washer Fluid:
Using windshield washer fluid without
anti-freeze protection in freezing
temperatures is dangerous. The
washer fluid could freeze on the
windshield and block your vision. You
could have an accident. Don't use the
washer without first warming the
windshield and never use plain tap
water.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected from motor breakdown,
overheating and possible fire by a
circuit breaker. This mechanism will
automatically stop operation of the
blades, but only for about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don't resume functioning, consult
an Authorized Mazda Dealer as soon as
possible.
5-40
Driving Your Mazda
íSome models.
Switches and Controls
Mazda6_8T12-EA-03K_Edition1 Page156
Friday, December 5 2003 8:56 AM
Form No.8T12-EA-03K
Page 157 of 326

Black plate (157,1)
qWindshield Wipers
OFF
INT
1
2
Turn the wipers on by pulling the lever
down.
INT—Intermittent
1—Normal
2—Fast
Variable-speed intermittent wipers
Set the lever to INT and choose the
interval timing by rotating the ring.
OFF
INT
INT ring
One-touch wipers
For a single wiping cycle, push the lever
up to MIST.
MIST
OFF
qWindshield Washer
Pull the lever toward you and hold it to
spray washer fluid.
OFF
Washer
NOTE
With the wiper lever in the OFF or INT
position, the wipers will operate
continuously until the lever is released.
If the washer doesn't work, inspect the
fluid level (page 8-18). If it's OK, consult
an Authorized Mazda Dealer.
Driving Your Mazda
Switches and Controls
5-41
Mazda6_8T12-EA-03K_Edition1 Page157
Friday, December 5 2003 8:56 AM
Form No.8T12-EA-03K
Page 158 of 326

Black plate (158,1)
Rear Window Wiper and
Washerí
The ignition switch must be in the ON
position.
qRear Window Wiper
WasherOFF INT ON Washer
Turn the wiper on by turning the rear
wiper/washer switch.
ON—Normal
INT—Intermittent
qRear Window Washer
To spray washer fluid, turn the rear wiper/
washer switch to theposition. After the
switch is released, the washer will stop.
NOTE
There are two washer positions: up and
down. In the down washer position, the
wiper will not be activated.
If the washer doesn't work, inspect the
fluid level (page 8-18). If it's OK and the
washer still doesn't work, consult an
Authorized Mazda Dealer.
Rear Window Defroster
The rear window defroster clears frost,
fog, and thin ice from the rear window.
The ignition switch must be in the ON
position.
Press the switch to turn on the rear
window defroster. The rear window
defroster operates for about 15 minutes
and turns off automatically.
The indicator light illuminates during
operation.
To turn off the rear window defroster
before the 15 minutes has elapsed, press
the switch again.
Manual Type Air-Conditioning
5-42
Driving Your Mazda
íSome models.
Switches and Controls
Mazda6_8T12-EA-03K_Edition1 Page158
Friday, December 5 2003 8:56 AM
Form No.8T12-EA-03K
Page 243 of 326

Black plate (243,1)
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction .................................................................................. 8-2
Introduction ............................................................................... 8-2
Scheduled Maintenance ................................................................ 8-3
Scheduled Maintenance ............................................................ 8-3
Owner Maintenance ..................................................................... 8-7
Owner Maintenance Schedule .................................................. 8-7
Owner Maintenance Precautions ............................................... 8-8
Engine Compartment Overview ................................................ 8-9
Engine Oil ............................................................................... 8-10
Engine Coolant ....................................................................... 8-12
Brake/Clutch Fluid .................................................................. 8-15
Power Steering Fluid ............................................................... 8-16
Automatic Transaxle Fluid (ATF) ........................................... 8-17
Washer Fluid ........................................................................... 8-18
Body Lubrication .................................................................... 8-19
Air Filter .................................................................................. 8-20
Wiper Blades ........................................................................... 8-21
Battery ..................................................................................... 8-26
Tires ........................................................................................ 8-27
Light Bulbs ............................................................................. 8-31
Fuses ....................................................................................... 8-38
Appearance Care ........................................................................ 8-43
How to Minimize Environmental Paint Damage .................... 8-43
Exterior Care ........................................................................... 8-45
Interior Care ............................................................................ 8-48
8-1
Mazda6_8T12-EA-03K_Edition1 Page243
Friday, December 5 2003 8:58 AM
Form No.8T12-EA-03K
Page 247 of 326

Black plate (247,1)
qSchedule 2
Maintenance IntervalNumber of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
ENGINE
Drive belts (tension)2.3-liter engine I
3.0-liter engine I I
Engine valve clearance (2.3-liter engine) Audible inspect every 120,000km (75,000miles), if noisy, adjust
Engine oilPuerto Rico Replace every 5,000km (3,000miles) or 3 months
Others R R R R R R RRRRRR
Engine oil filter R R R R R R RRRRRR
COOLING SYSTEM
Cooling system I I
Engine coolantReplace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level I I I I I I IIIIII
FUEL SYSTEM
Air filterPuerto Rico R R
Others R
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
IGNITION SYSTEM
Spark plugsUSA Replace every 96,000km (60,000miles)
Others
*2Replace every 120,000km (75,000miles)
ELECTRICAL SYSTEM
Function of all lights I I I I I I IIIIII
CHASSIS and BODY
Brake lines, hoses and connections I I
Brake and clutch fluid level I I I I I I IIIIII
Disc brakesIIII
Tire (Rotation) Rotate every 8,000km (5,000miles)
Tire inflation pressure and tire wear I I I I I I IIIIII
Steering operation and linkages I I
Power steering fluid level I I I I I I IIIIII
Front suspension ball joints I I
Driveshaft dust boots I I
Exhaust system and heat shields Inspect every 72,000km (45,000miles) or 60 months
All locks and hinges L L L L L LLLLLLL
Washer fluid level I I I I I I IIIIII
Maintenance and Care
Scheduled Maintenance
8-5
Mazda6_8T12-EA-03K_Edition1 Page247
Friday, December 5 2003 8:58 AM
Form No.8T12-EA-03K
Page 249 of 326

Black plate (249,1)
Owner Maintenance Schedule
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.
qWhen Refueling
lBrake and clutch fluid level (page 8-15)
lEngine coolant level (page 8-12)
lEngine oil level (page 8-10)
lWasher fluid level (page 8-18)
qAt Least Monthly
Tire inflation pressures (page 8-28)
qAt Least Twice a Year (For Example, Every Spring and Fall)
lAutomatic transaxle fluid level (page 8-17)
lPower steering fluid level (page 8-16)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
lAir filter (page 8-20)
lEngine coolant (page 8-12)
lEngine oil (page 8-11)
Maintenance and Care
Owner Maintenance
8-7
Mazda6_8T12-EA-03K_Edition1 Page249
Friday, December 5 2003 8:58 AM
Form No.8T12-EA-03K