light MAZDA MODEL 6 SPORTS SEDAN 2004 Owners Manual (in English)

Black plate (275,1)
3. Disconnect the bulb from the socket.
Socket
Brake lights/Taillights, Rear turn signallights
(Sedan)
1. Pull the center section of the plastic
retainer and remove the retainers and
partially open the trunk side trim.
Trunk side trim
Removal
Installation
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
Socket
Rear turn signal lights
Brake lights/Taillights
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
(Hatchback)
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
(Wagon)
1. Turn the knob and remove the cover.
Left side
Right side
2. Turn the socket and bulb assembly
counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-33
Mazda6_8T12-EA-03K_Edition1 Page275
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (276,1)
3. Disconnect the bulb from the socket.
Socket
Rear turn signal lights
Brake lights/Taillights
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Reverse lights, Taillights
(Sedan)
1. Pull the center section of the plastic
retainer and remove the retainers, then
remove the trunk rear trim.
Trunk rear trim Installation Removal
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
Reverse lights
Taillights
Socket
4. Install the new bulb in the reverse order
of removal.
(Hatchback/Wagon)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Reverse lights
Taillights
Socket
4. Install the new bulb in the reverse order
of removal.
High-mount brake light
(Sedan)
1. Remove the high-mount brake light
component.
8-34
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page276
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (277,1)
2. Detach the electrical connector from
the socket.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
Socket
5. Install the new bulb in the reverse order
of removal.
(Hatchback)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Socket
4. Install the new bulb in the reverse order
of removal.(Wagon)
1. Remove the liftgate upper trim and
high-mount brake light component.
Liftgate upper trim
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Socket
4. Install the new bulb in the reverse order
of removal.
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens.
Maintenance and Care
Owner Maintenance
8-35
Mazda6_8T12-EA-03K_Edition1 Page277
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (278,1)
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Withoverhead console)
1. Remove the screws.
2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.4. Disconnect the bulb from the socket.
Socket
5. Install the new bulb in the reverse order
of removal.
Overhead light/Map lights (Withoutoverhead console)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
8-36
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page278
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (279,1)
3. Disconnect the bulb from the socket.
Socket
4. Install the new bulb in the reverse order
of removal.
Courtesy lights, Vanity mirror lights,and Luggage compartment light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens.
2. Disconnect the bulb by pulling it out.
Edge Courtesy lights
Vanity mirror lights
Edge
(Hatchback)Luggage compartment light
Luggage compartment light
(Wagon)
Edge
3. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-37
Mazda6_8T12-EA-03K_Edition1 Page279
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (280,1)
Trunk light (Sedan)
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's sidekick-panel
If the electrical system doesn't work, first
inspect fuses on the driver's side kick-
panel.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover by sliding
the cover straight back toward you.
Fuse panel cover
CAUTION
Pulling the cover off sideways may
break the retaining tabs off.
8-38
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page280
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (281,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
Fuse puller
Engine compartment fuse box
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the SPARE circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
Fuse block cover
Tab
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-40).
Maintenance and Care
Owner Maintenance
8-39
Mazda6_8T12-EA-03K_Edition1 Page281
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (282,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
1 SPARE 20A—
2 SPARE 15A—
3 SPARE 10A—
4—— —
5—— —
6 INJ 15A Injector
7ENG
BAR10A
*1Air flow sensor, EGR control
valve
15A*2
8ENG
BAR2*115A O2 sensor
ENG
BB
*25A Cooling fan
9HEAD
LR10A Headlight-low beam (Right)
10HEAD
LL10A Headlight-low beam (Left)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
11HEAD
HL10A Headlight-high beam (Left)
12HEAD
HR10A Headlight-high beam (Right)
13ETC 7.5A Accelerator position sensor
14 HAZARD10A Turn signal lights
15STOP 15A Brake/Taillights
16TCM*110A TCM
IG1*215A O2 sensor
17 ENGB7.5A PCM, TCM
18FUEL
PUMP15A Fuel pump
19IG KEY 40AWindshield wiper and washer,
Engine control unit, Lighter
20P.WIND 30A Power window
21—— —
22—— —
8-40
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page282
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (283,1)
DESCRIP-
TIONFUSE
RAT-
INGPROTECTED
COMPONENT
23IG
KEY230AReverse lights, Heater control
unit
24 BLOWER40A Blower motor
25BTN 40AOverhead light, Power door
lock
26—— —
27DEFOG 40A Rear window defroster
28ABS 60A ABSí
29AD
FA N*130A Cooling fan
FAN2*2
30FA N*130A Cooling fan
FAN1*2
31TAIL 10ABrake/Taillights, License plate
lights, Parking lights
32 ILLUMI10A Dashboard illumination
33MAG 10A Magnet clutch
34AUDIO 15A Audio system
35P.SEAT 30A Power seatí
36 OPENER7.5A Fuel lid opener
37—— —
38—— —
39FOG 15A Fog lightsí
40MAIN100A*1For protection of all circuits
120A*2
*1 2.3-liter engine
*2 3.0-liter engine
Maintenance and Care
Owner Maintenance
8-41íSome models. Mazda6_8T12-EA-03K_Edition1 Page283
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (284,1)
Fuse block (Driver's side kick-panel)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1ENGINE
IG15A Engine control system
2METER
IG15A Instrument cluster
3 SEAT 15ASeat warmer
í, Rear
window defroster
4 M.DEF 7.5A Mirror defroster
5 WIPER 20AWindshield wiper and
washer
6 SAS 15A ABS unit
í, SAS unit
7 BACK 5A Reverse lights
8 A/C 15A Heater
9METER
ACC5A Instrument cluster
10 CIGAR 15A Lighter
11 ROOM 15A Overhead light
12 R.WIP
í10A Rear wiperí
13 MIRROR 5APower control mirror,
Audio system
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
14
R.CIGAR15A Accessory socket
15—— —
16 D.LOCK 30A Power door lock
17—— —
8-42
Maintenance and Care
íSome models.
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page284
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K