engine oil MAZDA MODEL 626 2001 User Guide

Form No. 8P95-EA-00G
Maintenance8-12•Engine coolant
(page 8-22)
• Engine oil and oil filter
(page 8-18)

083-2A2E
 Owner Maintenance Precautions
Improper or incomplete service may
result in problems. This section gives
instructions only for items easy to
perform.
WARNING
!
Maintenance Procedures:Performing maintenance work on
a vehicle can be dangerous. You
can be seriously injured while
performing some maintenance
procedure. If you lack sufficient
knowledge and experience or the
proper tools and equipment to do
the work, have it done by a
qualified technician.As explained in the Introduction (page
8-2), several procedure can be done
only by a qualified service technician
with special tools.

Form No. 8P95-EA-00G
Maintenance8-14
083-4AE
 Engine Compartment Overview
Cooling system cap
2.0-liter engine
Engine oil dipstick Air filter
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Brake/Clutch fluid reservoir
Fuse block
Battery
Coolant reservoir
Windshield washer fluid reservoir
Power steering fluid reservoir
Engine oil-filler cap
J94A7001A

Form No. 8P95-EA-00G
Maintenance
8-15
Engine oil-filler cap
Engine oil dipstick
Air filter
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Brake/Clutch fluid reservoir
Fuse block
Battery
Coolant reservoir
Windshield washer fluid reservoir
J94A7002A2.5-liter engine
Power steering fluid reservoir
Cooling system cap

Form No. 8P95-EA-00G
J94A7003
(J18T7003)
(ILSAC)
Maintenance8-16

083-5A2E
 Engine Oil
 Recommended oil
Oil container labels provide important
information.
The quality designation “SG”, “SH”,“
SJ ”, or “ILSAC” must be on the label.
Engine oil viscosity, or thickness, has
an effect on fuel economy and
cold-weather operation (starting and
oil flow). Low-viscosity engine oils
can provide improved fuel ec onomy
and cold-weather performance. But high-temperature weather
conditions require higher-viscosity
engine oils for satisfactory lubrication.
When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended
viscosity from this chart.
–20 0 20 40 60 80 100 120
–30
–20–10 0 10 20 30 40 50
°C
( ° F)
Oil
5W-30 10W-30
|| | ||| | |||| | | | | | |

Form No. 8P95-EA-00G
Maintenance
8-17
CAUTION
!
Using oils of viscosity besides
those recommended for specific
temperature ranges could result in
engine damage.Energy conserving oils are
recommended. A chief contribution
they make to fuel economy is reducing
the amount of fuel necessary to
overcome engine friction.

083-6A2E
J94A7005
2.0-liter engine
OKInspecting engine oil level
1. Be sure the vehicle is on a level surface.
2. Warm up the engine to normal operating temperature.
OK
J94A7004
2.5-liter engine3. Turn it off and wait 5 minutes forthe oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and reinsert it fully.

Form No. 8P95-EA-00G
Maintenance8-185. Pull it out again and examine thelevel. It’ s OK between L and F.
But if it’ s near at or below L, add
enough oil to bring the level to F.
CAUTION
!
Don’ t add engine oil over F.
This may cause engine damage.NOTEThe distance between L and F on
the dipstick represents 1.0 L (1.06
US qt, 0.88 Imp qt).

083-7CE
Changing engine oil and filter
Change engine oil and filter according
to Scheduled Maintenance (page
8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
WARNING
!
Handling Used Engine Oil:Continuous contact with used
engine oil could be dangerous. It
could cause skin cancer. Always
wash with soap and water
immediately after changing oil
and filter.

Form No. 8P95-EA-00G
J94A7007 (J18T7009)
Loosen
Drain plug Oil-filler cap
Tighten
2.5-liter engine
Maintenance
8-19
J94A7006
(J18T7008)
Loosen
2.0-liter engine
Oil-filler capTighten
Drain plug
Changing engine oil
1. Warm up the engine for a few minutes and turn it off. Remove the
oil-filler cap. 2. Remove the drain plug and drain
the oil into a suitable container.
WARNING
!
Checking or Changing EngineOil:Hot engine oil could be
dangerous. If the engine has been
running, the engine oil becomes
very hot. You could be seriously
burned. Don’ t check or change
the engine oil when the engine is
hot.

Form No. 8P95-EA-00G
Maintenance8-20
083-47B1E
3. Replace the plug tightly after theoil has thoroughly drained.
4. Fill the engine with new oil to the F mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the drain plug for leaks.
7. Turn it off and wait 5 minutes for the oil to return to the oil pan.

 083-48BE
Check the oil level and fill to the F
mark if necessary.
Oil capacity
(General reference only)
2.0-liter engine:
3.3 L (3.5 US qt, 2.9 Imp qt)
2.5-liter engine: 3.7 L (3.9 US qt, 3.3 Imp qt)
NOTE• The indicated engine oil
capacities are for general
reference purposes only. When
adding or changing oil, verify
the engine oil level with the oil
dipstick.
• Use only specified engine oil
(page 8-16).Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized
Mazda Dealer should do the work.

Form No. 8P95-EA-00G
Maintenance
8-27
WARNING
!
Low Brake/Clutch Fluid Levels:Low brake/clutch fluid levels
could be dangerous. Low levels
could signal brake lining wear or
a brake system leak. Your brakes
could fail and cause an accident.
If you find a low fluid level, have
the brakes and clutch inspected.
Q083-15FE
J94A7015Inspecting Power Steering Fluid
Level
Inspect the fluid level at each engine
oil change. Add fluid if necessary; it
does not require periodic changing. J94A7016
(J18T7019)
Low
OK
High
The level must be kept between the
HIGH and LOW marks.

Form No. 8P95-EA-00G
Maintenance
8-33

083-22DE
J94A7019 Inspecting Washer Fluid Level
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
Use plain water if fluid is unavailable.
But use only washer fluid in cold
weather to prevent it from freezing.
083-23A2E
WARNING
!
Substitute Washer Fluid:Using radiator antifreeze as
washer fluid is dangerous. If
sprayed on the windshield, it will
dirty the windshield, affect your
visibility, and could result in an
accident. Use only windshield
washer fluid or plain water in the
reservoir.
083-26AE
 Body Lubrication
All moving points of the body, such as
door and hood hinges and locks,
should be lubricated each time the
engine oil is changed. Use a
nonfreezing lubricant on locks during
cold weather.
Make sure the engine hood’ s
secondary latch keeps the hood from
opening when the primary latch is
released.