fuel MAZDA MODEL 626 2001 Owner's Manual

Form No. 8P95-EA-00G
Appearance Care7-10
078-5A1E

Underbody Maintenance
Road chemicals and salt used for ice
and snow removal and solvents used
for dust control may collect on the
underbody. If not removed, they will
speed up rusting and deterioration of
such underbody parts as fuel lines,
frame, floor pan, and exhaust system,
even though these parts may be coated
with anticorrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try
also to do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It will do more harm than good to
wet down the road grime without
removing it.
The lower edges of doors, rocker
panels, and frame members have drain
holes that should not be clogged.
Water trapped there will cause rusting.
WARNING
!
Driving with Wet Brakes:Driving with wet brakes is
dangerous. Increased stopping
distance or the vehicle pulling to
one side when braking could
result in a serious accident. Light
braking will indicate whether the
brakes have been affected. Dry
the brakes by driving very slowly
and applying the brakes lightly
until brake performance is
normal.

Form No. 8P95-EA-00G
I: Inspect and repair, clean, adjust, or replace if necessary
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R : Replace
Maintenance
8-5
Schedule 1 (Cont’d)
MAINTENANCE
INTERVALS
Number of months or miles (kilometers), whichever comes first
INTERVALS
Months
6
12
18
24
30
36
42
48
MAINTENANCE

1000 km
12
24
36
48
60
72
84
96
MAINTENANCE

ITEM
(
1000 miles)
(7.5)
(15)
(22.5)
(30)
(37.5)
(45)
(52.5)
(60)
Hoses and tubes for emission
I*
1
Air filter
R
R
Spark plugs
2.0-liter engine
R
R
Spark plugs
2.5-liter engine
Replace every 96,000 km (60,000 miles)
Idle speed
I
I
Fuel lines and hoses
I*1
I*1
Cooling system
I
I
Engine coolant
Replace at first 168,000 km (105,000 miles) or 60 months;
after that, every 48,000 km (30,000 miles) or 24 months
Brake lines, hoses and connections
I
I
*1 According to state and federal regulations, failure to perform maintenan\
ce on these items will not void your emissions warranties. However, Mazda
recommends that all maintenance services be performed at the recommended\
time or kilometrage (mileage) period to ensure long-term reliability.

Form No. 8P95-EA-00G
I: Inspect and repair, clean, adjust, or replace if necessary
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R : Replace
Maintenance8-8Schedule 2 (Cont ’d)
MAINTENANCE
INTERVALS
Number of months or miles (kilometers), whichever comes first
INTERVALS
Months
4
8
12
16
20
24
28
32
36
40
44
48
MAINTENANCE

1000 km
8
16
24
32
40
48
56
64
72
80
88
96
MAINTENANCE

ITEM
(
1000 miles)
(5)
(10)
(15)
(20)
(25)
(30)
(35)
(40)
(45)
(50)
(55)
(60)
Spark plugs
2.0-liter engine
R
R
Spark plugs
2.5-liter engine
Replace every 96,000 km (60,000 miles)
Idle speed
I
I
Fuel lines and hoses
I*1
I*
1
Cooling system
I
I
Engine coolant
Replace at first 168,000 km (105,000 miles) or 60 months;
after that, every 48,000 km (30,000 miles) or 24 months
Engine coolant level
I
I
I
I
I
I
I
I
I
I
I
I
Function of all lights
I
I
I
I
I
I
I
I
I
I
I
I
Brake lines, hoses and connections
I
I
*1 According to state and federal regulations, failure to perform maintenan\
ce on these items will not void your emissions warranties. However, Mazda
recommends that all maintenance services be performed at the recommended\
time or kilometrage (mileage) period to ensure long-term reliability.

Form No. 8P95-EA-00G
Maintenance
8-11
083-1AE
Owner MaintenanceOwner Maintenance Schedule
The owner or a qualified service
technician should make these vehicle
inspections at the indicated intervals to
ensure safe and dependable operation.
Bring any problem to the attention of
an Authorized Mazda Dealer or
qualified service technician as soon as
possible.
 When refueling
• Brake and clutch fluid level
(page 8-25) •
Engine coolant level
(page 8-21)
• Engine oil level
(page 8-17)
• Washer fluid level
(page 8-33)
 At least monthly
• Tire inflation pressures
(page 8-41)
083-46A1E
At least twice a year
(for example, every spring and
fall)
• Automatic transaxle fluid level
(page 8-29)
• Power steering fluid level
(page 8-27)
You can do the following scheduled
maintenance items if you have some
mechanical ability and a few basic
tools and if you closely follow the
directions in this manual.
• Air filter
(page 8-34)

Form No. 8P95-EA-00G
J94A7003
(J18T7003)
(ILSAC)
Maintenance8-16

083-5A2E
 Engine Oil
 Recommended oil
Oil container labels provide important
information.
The quality designation “SG”, “SH”,“
SJ ”, or “ILSAC” must be on the label.
Engine oil viscosity, or thickness, has
an effect on fuel economy and
cold-weather operation (starting and
oil flow). Low-viscosity engine oils
can provide improved fuel ec onomy
and cold-weather performance. But high-temperature weather
conditions require higher-viscosity
engine oils for satisfactory lubrication.
When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended
viscosity from this chart.
–20 0 20 40 60 80 100 120
–30
–20–10 0 10 20 30 40 50
°C
( ° F)
Oil
5W-30 10W-30
|| | ||| | |||| | | | | | |

Form No. 8P95-EA-00G
Maintenance
8-17
CAUTION
!
Using oils of viscosity besides
those recommended for specific
temperature ranges could result in
engine damage.Energy conserving oils are
recommended. A chief contribution
they make to fuel economy is reducing
the amount of fuel necessary to
overcome engine friction.

083-6A2E
J94A7005
2.0-liter engine
OKInspecting engine oil level
1. Be sure the vehicle is on a level surface.
2. Warm up the engine to normal operating temperature.
OK
J94A7004
2.5-liter engine3. Turn it off and wait 5 minutes forthe oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and reinsert it fully.

Form No. 8P95-EA-00G
Maintenance8-40•Keep terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.
• Rinse off spilled electrolyte
immediately with a solution of
water and baking soda.
• If the vehicle will not be used for
an extended time, disconnect the
battery cables.


083-33A4E
Tires
For reasons of proper performance,
safety, and better fuel economy,
always maintain recommended tire
inflation pressures and stay within the
recommended load limits and weight
distribution.
WARNING
!
Using Different Tire Types:Driving your vehicle with
different types of tires is
dangerous. It could cause poor
handling and poor braking;
leading to loss of control. Except
when using the temporary spare
tire, use only the same type tires
(radial, bias-belted, bias-type) on
all four wheels.

Form No. 8P95-EA-00G
Maintenance8-42NOTE•Warm tires normally exceed
recommended pressures. Don’ t
release air from warm tires to
adjust the pressure.
• Underinflation can cause
reduced fuel economy and poor
sealing of the tire bead, which
will deform the wheel and
cause separation of tire from
rim.
• Overinflation can produce a
harsh ride and a greater
possibility of damage from road
hazards.
(Continued)
•Keep your tire pressure at the
correct levels. If one frequently
needs inflating, have it
inspected.
WARNING
!
Incorrect Tire Inflation:Overinflation or underinflation of
tires is dangerous. Adverse
handling or unexpected tire
failure could result in a serious
accident. Always inflate the tires
to the correct pressure (page
10-6).
083-34A2E
J94A7027_a (J18T7031)
Front
Do not include (TEMPORARY USE ONLY
spare tire) in rotation.
 Tire rotation
To equalize tread wear, rotate the tires
every 6,000 km (3,750 miles), or
sooner if irregular wear develops.
During rotation, inspect them for
correct balance.

Form No. 8P95-EA-00G
Customer Information9-10


089-1A2E
Outside the United States and
CanadaGovernment regulations in the United
States require that automobiles meet
specific emission regulations and
safety standards. Therefore, vehicles
built for use in the United States, its
territories, and Canada may differ
from those sold in other countries.
The differences may make it difficult
or even impossible for your vehicle to
receive satisfactory servicing in other
countries. We strongly recommend
that you NOT take your Mazda
outside these areas. Example of problems encountered
outside the United States and Canada:
•
Recommended fuel may be
unavailable. Any kind of leaded
fuel or low-octane fuel will affect
vehicle performance and damage
the emission controls and engine.
• Proper repair facilities, tools,
testing equipment, and replacement
parts may not be available.
The manufacturer ’s warranty applies
only to Mazda vehicles registered and
normally operated in the United States,
its territories, and Canada.
090-3AE
Add-On Non-Genuine Parts
and AccessoriesNon-genuine parts and accessories for
Mazda vehicles can be found in stores.
These may fit your vehicle, but they
are not approved by the manufacturer
for use with Mazda vehicles. When
you install non-genuine parts or
accessories, they could affect your
vehicle’ s performance or safety
system; the manufacturer ’s warranty
doesn’ t cover this. Before you install
any non-genuine parts or accessories,
consult an Authorized Mazda Dealer.

Form No. 8P95-EA-00G
Index11-4
PagePage Page
Winter driving 4-12
. . . . . . . . . . . . . . . . .
EEmergency Starting
Jump-starting 6-4 . . . . . . . . . . . . . . . . . .
Push-starting 6-7 . . . . . . . . . . . . . . . . . . .
Emission Control System 4-4 . . . . . . . . . . .
Engine Compartment Overview 8-14 . . . . .
Engine Coolant Adding coolant 8-21 . . . . . . . . . . . . . . . .
Changing coolant 8-22 . . . . . . . . . . . . . .
Inspecting coolant level 8-21 . . . . . . . . .
Overheating 6-2 . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature Gauge
(see Water)
Engine Exhaust (Carbon Monoxide) 4-6 . .
Engine Oil Changing engine oil and filter 8-18 . . . .
Inspecting engine oil level 8-17 . . . . . . .
Recommended oil 8-16 . . . . . . . . . . . . . . Engine Oil Pressure Warning Light 5-38
. . .
Engine Starting 5-4 . . . . . . . . . . . . . . . . . . .
Exhaust (Carbon Monoxide) 4-6 . . . . . . . .
Exterior Care 7-6 . . . . . . . . . . . . . . . . . . . .
Eyeglass Holder 5-57 . . . . . . . . . . . . . . . . .
FFinish Damage 7-9
. . . . . . . . . . . . . . . . . . .
Flasher, Hazard Warning 6-2
. . . . . . . . . . .
Flat Tire 6-19
. . . . . . . . . . . . . . . . . . . . . . .
Fluids Automatic transaxle 8-29
. . . . . . . . . . . .
Brake/clutch 8-25
. . . . . . . . . . . . . . . . . .
Power steering 8-27
. . . . . . . . . . . . . . . .
Washer 8-33
. . . . . . . . . . . . . . . . . . . . . .
Foot Brake 5-19
. . . . . . . . . . . . . . . . . . . . .
Front Seat Belts 2-17
. . . . . . . . . . . . . . . . .
Front Seats (Electrically Operated) Head restraint height adjustment 2-9 . . .
Height adjustment 2-7
. . . . . . . . . . . . . . . Recline
2-7
. . . . . . . . . . . . . . . . . . . . . . .
Seat cushion front height
adjustment 2-6
. . . . . . . . . . . . . . . . . . . . .
Seat cushion rear height
adjustment 2-6
. . . . . . . . . . . . . . . . . . . . .
Seat slide 2-6
. . . . . . . . . . . . . . . . . . . . . .
Front Seats (Manually Operated) Head restraint height adjustment 2-4 . . .
Recline 2-3
. . . . . . . . . . . . . . . . . . . . . . .
Slide 2-2
. . . . . . . . . . . . . . . . . . . . . . . . .
Tilt 2-5
. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Gauge 5-34
. . . . . . . . . . . . . . . . . . . . .
Fuel Requirements 4-2
. . . . . . . . . . . . . . . .
Fuel-Filler Cap 3-30
. . . . . . . . . . . . . . . . . .
Fuel-Filler Lid 3-30
. . . . . . . . . . . . . . . . . .
Fuses 6-8
. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse panel description 6-12
. . . . . . . . . .
Replacement 6-8
. . . . . . . . . . . . . . . . . . .