steering MAZDA MODEL 626 2002 User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2002, Model line: MODEL 626, Model: MAZDA MODEL 626 2002Pages: 250, PDF Size: 4.83 MB
Page 75 of 250
4-7
Before Driving Your Mazda
Form No. 8Q50-EA-01G
Driving Tips
No special break-in is necessary, but a few
precautions in the first 1,000 km (600
miles) may add to the performance,
economy, and life of your Mazda.
•Don ’t race the engine.
• Don ’t maintain one constant speed for
long.
• Don ’t drive constantly at full-throttle or
high engine rpm for extended periods
of time.
• Avoid unnecessary hard stops.
• Avoid full-throttle starts. How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save money on
fuel and repairs.
•
Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
• Av o i d f a s t s t a r t s .
• Keep the engine tuned. Follow the
maintenance schedule (page 8-3)
and have an Authorized Mazda Dealer
perform inspections and servicing.
• Use the air conditioner only when
necessary.
• Slow down on rough roads.
• Keep the tires properly inflated.
• Don ’t carry unnecessary weight.
• Don ’t rest your foot on the brake pedal
while driving.
• Keep the wheels in correct alignment.
• Keep windows closed at high speeds.
• Slow down when driving in crosswinds
and headwinds.
Break-In PeriodMoney-Saving Suggestions
Coasting:Turning off the engine to coast down
a hill is dangerous. This causes the
loss of power steering and power
brake control. Any loss of steering or
braking control could cause an
accident. Never turn off the engine
and coast down a hill.
WARNING
J94S.book Page 7 Saturday, June 23, 2001 1:04 PM
Page 76 of 250
4-8
Before Driving Your Mazda
Driving Tips
Form No. 8Q50-EA-01G
When driving on ice or in water, snow,
mud, sand, or similar hazard:
•Be cautious and allow extra distance
for braking.
• Avoid sudden braking and quick
steering.
• If your vehicle is not equipped with
ABS, brake with the pedal by using a
light up-down motion. Don ’t hold the
pedal down constantly.
If your vehicle is equipped with ABS,
don’ t pump the brakes. Continue to
press down on the brake pedal.
• If you get stuck, shift to 1 (L) or 2 (S)
and accelerate slowly. Don ’t spin the
front wheels.
• For more traction in starting, use sand,
rock salt, chains, carpeting, or other
nonslip material under the front
wheels. If you must rock the vehicle to free it from
snow, sand, or mud, depress the
accelerator slightly and slowly move the
shift lever back and forth from 1 (D) to R.
Hazardous Driving
Downshifting on Slippery Surfaces:Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident. If it is
necessary to downshift on slippery
surfaces, be very careful.
NOTE
Use snow chains only on the front
wheels.
WARNING
Rocking the Vehicle
Spinning the Wheels:When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries. Don
’t spin the wheels at
more than 56 km/h (35 mph) , and
don ’t allow anyone to stand behind a
wheel when pushing the vehicle.
Too much rocking may cause engine
overheating, transaxle failure, and tire
damage.
WARNING
CAUTION
J94S.book Page 8 Saturday, June 23, 2001 1:04 PM
Page 81 of 250
5-1
Form No. 8Q50-EA-01G
5Driving Your Mazda
Explanation of instruments and controls.
Starting and Driving ................................................................... 5- 2
Ignition Switch ........................................................................ 5- 2
Starting the Engine .................................................................. 5- 3
Brake System ........................................................................... 5- 4
Manual Transaxle Operation ................................................... 5- 8
Automatic Transaxle Controls ................................................. 5- 9
Power Steering ......................................................................... 5-12
Cruise Control ......................................................................... 5-13
Traction Control System (TCS) ............................................... 5-16
Instrument Cluster and Indicators ............................................ 5-19
Meters and Gauges .................................................................. 5-19
Warning/Indicator Lights and Beeps ........................................ 5-23
Warning/Indicator Lights ......................................................... 5-23
Beeps ....................................................................................... 5-31
Switches and Controls ................................................................. 5-32
Lighting Control ...................................................................... 5-32
Turn and Lane-Change Signals ............................................... 5-33
Daytime Running Lights ......................................................... 5-33
Windshield Wipers and Washer ............................................... 5-34
Rear Window Defroster ........................................................... 5-35
Horn ......................................................................................... 5-36
Hazard Warning Flasher .......................................................... 5-36
J94S.book Page 1 Saturday, June 23, 2001 1:04 PM
Page 82 of 250
5-2
Driving Your Mazda
Form No. 8Q50-EA-01G
Starting and Driving
Ignition Switch Positions
LOCK
The steering wheel locks to protect
against theft. Only in this position can the
key be removed.
Manual transaxle
When turning the ignition switch to the
LOCK position, push the key in at the
ACC position. Automatic transaxle
When turning the ignition switch to the
LOCK position, keep the shift lever in P.
Ignition Switch
ON(II)
ACC(I)
LOCK(0) Push the key
Removing the Key:It
’s dangerous to remove the key from
the ignition switch while the vehicle is
moving. Removing the key allows the
steering wheel to lock. You will lose
steering control and a serious
accident could occur.
Remove the key only when the vehicle
is parked.
Not Setting the Parking Brake:
Leaving the driver ’s seat without
setting the parking brake is
dangerous. Unexpected vehicle
movement could occur if the parking
brake is not set. This could cause an
accident. Before leaving the driver ’s
seat, always set the parking brake and
make sure the shift lever is in P with
an automatic transaxle or in 1 or R
with a manual transaxle.
ON(II)
ACC(I)
LOCK(0) Shift lever
engaged in P
(park)
WARNING
J94S.book Page 2 Saturday, June 23, 2001 1:04 PM
Page 83 of 250
5-3
Driving Your Mazda
Starting and Driving
Form No. 8Q50-EA-01G
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes)should be inspected before
the engine is started (page 5-23).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-23).
Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened. 1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. (Manual transaxle)
Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the
clutch pedal is not pushed down all the
way.
J94S.book Page 3 Saturday, June 23, 2001 1:04 PM
Page 92 of 250
5-12
Driving Your Mazda
Starting and Driving
Form No. 8Q50-EA-01G
Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or 1, depending on the load
weight and grade steepness.
3. Release all brakes while gradually accelerating.
Descending steep grades
When descending a steep grade, shift to 2
or 1, depending on load weight and grade
steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating. Power steering is only operable when the
engine is running. If the engine is off or if
the power steering system is inoperable,
you can still steer, but it requires more
physical effort.
If the steering feels rigid during normal
driving, consult an Authorized Mazda
Dealer.
Power Steering
Never hold the steering wheel to the
extreme left or right for more than five
seconds with the engine running.
This could damage the power steering
system.
CAUTION
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM
Page 116 of 250
5-36
Driving Your Mazda
Switches and Controls
Form No. 8Q50-EA-01G
To sound the horn, press around the
mark of the steering wheel.The hazard warning lights should always
be used when you stop on or near a
roadway.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning switch and all
four turn signals will flash at once.
HornHazard Warning Flasher
NOTE
•
The turn signals don ’t work when
the hazard warning lights are on.
• Check local regulations about the
use of hazard warning lights while
the vehicle is being towed. They
may forbid it.
J94S.book Page 36 Saturday, June 23, 2001 1:04 PM
Page 165 of 250
7-5
In Case of an Emergency
Flat Tire
Form No. 8Q50-EA-01G
If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous.1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic transaxle in park (P), a manual
transaxle in reverse (R), and turn off
the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire (page 7-3).
6. Block the wheel diagonally opposite the flat tire. When blocking a front
wheel, place the block in front of the
tire. When blocking a rear wheel, place
the block behind the tire.
Changing a Flat Tire
NOTE
If the following occurs while driving, it
could indicate a flat tire.
•Steering becomes difficult.
• The vehicle begins to vibrate
excessively.
• The vehicle pulls in one direction.
Jacking a Vehicle:Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by jack.
WARNING
NOTE
Make sure the jack is well lubricated
before using it.
J94S.book Page 5 Saturday, June 23, 2001 1:04 PM
Page 177 of 250
8-1
Form No. 8Q50-EA-01G
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction ................................................................................. 8- 2
Introduction ............................................................................. 8- 2
Scheduled Maintenance .............................................................. 8- 3
Scheduled Maintenance ........................................................... 8- 3
Owner Maintenance .................................................................... 8- 7
Owner Maintenance Schedule ................................................. 8- 7
Owner Maintenance Precautions ............................................. 8- 8
Engine Compartment Overview .............................................. 8- 9
Engine Oil ................................................................................ 8-10
Engine Coolant ........................................................................ 8-13
Brake/Clutch Fluid .................................................................. 8-15
Power Steering Fluid ............................................................... 8-17
Automatic Transaxle Fluid (ATF) ........................................... 8-18
Washer Fluid ............................................................................ 8-20
Body Lubrication ..................................................................... 8-21
Air Filter .................................................................................. 8-21
Wiper Blades ........................................................................... 8-22
Battery ..................................................................................... 8-24
Tires ......................................................................................... 8-25
Light Bulbs .............................................................................. 8-29
Fuses ........................................................................................ 8-35
Appearance Care ......................................................................... 8-40
How to Minimize Environmental Paint Damage ..................... 8-40
Exterior Care ........................................................................... 8-42
Interior Care ............................................................................ 8-45
J94S.book Page 1 Saturday, June 23, 2001 1:04 PM
Page 180 of 250
8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q50-EA-01G
Schedule 1
I : Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.) R: Replace
L : Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
Maintenance
Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first Months 6 12182430364248
×1000 Km 12 24 36 48 60 72 84 96
(×1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60)
Engine valve clearance I
Drive belts (tension) II
Engine timing belt Inspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Engine oil RRRRRRRR
Engine oil filter RRRRRRRR
Cooling system II
Engine coolant Replace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Idle speed II
Air filter RR
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugs 2.0-liter engine
(non-PLATINUM tipped type)
RR
2.5-liter engine
(PLATINUM tipped type) Replace every 96,000km (60,000miles)
Brake lines, hoses and connections II
Disc brakes II
Drum brakes II
Steering operation and linkages II
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body II
Exhaust system heat shields II
All locks and hinges LLLLLLLL
Refrigerant amount (if installed) IIII
Compressor operation (if installed) IIII
08.fm Page 4 Monday, June 25, 2001 5:12 PM