fog light MAZDA MODEL 626 2002 Owners Manual

5-35
Driving Your Mazda
Switches and Controls
Form No. 8Q50-EA-01G
One-touch wipers
For a single wiping cycle, push the lever
up to MIST.





Windshield Washer
Pull the lever toward you and hold it to
spray washer fluid. In the OFF or INT
position, the wipers will be activated until
the lever is released.
If the washer doesn ’t work, inspect the
fluid level (page 8-20). If it ’s OK, consult
an Authorized Mazda Dealer. The rear defroster clears frost, fog, and
thin ice from the rear window.
The ignition switch must be in the ON
position.
Push the switch to turn on the rear
window defroster; the indicator light will
come on.
Push the switch again to turn it off.
Rear Window Defroster
Don
’t use sharp instruments or
window cleaners with abrasives to
clean the inside of the rear window
surface. They may damage the
defroster grid inside the window.
NOTE
This defroster is not designed for
melting snow. If there is an
accumulation of snow on the rear
window, brush it off before using the
defroster.
CAUTION
J94S.book Page 35 Saturday, June 23, 2001 1:04 PM

6-2
Interior Comfort
Form No. 8Q50-EA-01G
Climate Control System





Operating the Climate Control
System
Operate the climate control system with
the engine running.





Clearing the Air Inlet
Clear all obstructions like leaves, snow
and ice from the hood and the air inlet in
the cowling grille to improve the system
efficiency.





Foggy Windows
The windows may fog up easily in humid
weather. Use the climate control system to
defog the windows.
To help defog the windows, operate the
air conditioner to dehumidify the air.





Outside/Recirculated Air
Position
Use the outside air position in normal
conditions. The recirculated air position
can be used temporarily when driving on
dusty roads or for quick cooling of the
interior.





Parking in Direct Sunlight
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then run
the climate control system.





Not Using for a Long Period
Run the air conditioner at least once a
month to keep internal parts lubricated.





Check the Refrigerant before
Weather Gets Hot
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
efficient. Consult an Authorized Mazda
Dealer for refrigerant inspection.
The optional air conditioner is filled with
R134a, a refrigerant that will not damage
the ozone layer.
If the air conditioner is low on refrigerant
or has a malfunction, consult an
Authorized Mazda Dealer.
Operating Tips
J94S.book Page 2 Saturday, June 23, 2001 1:04 PM

6-9
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
5. Adjust the fan control dial and temperature control dial to maintain
maximum comfort.




Ventilation
1. Set the mode selector switch to the
position.
2. Set the air intake selector switch to the outside air position (indicator light off).
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.






Windshield Defrosting and
Defogging
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-21).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner
off.
NOTE
• When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector switch to the
recirculated air position, then set the
fan control dial to the position 4.
• If warmer air is desired at floor
level, set the mode selector switch
at the position and adjust the
temperature control dial to maintain
maximum comfort.
• The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
CAUTION
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM

6-10
Interior Comfort
Climate Control System
Form No. 8Q50-EA-01G
1. Set the mode selector switch to the position.
2. Set the temperature control dial to the desired position.
3. Set the fan control dial to the desired speed.




Dehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector switch to the
desired position.
2. Set the air intake selector switch to the outside air position (indicator light off).
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.
5. Turn on the air conditioner.
Foggy Windshield:Using the position with the
temperature control set to the cold
position will cause the outside of the
glass to fog up. Your vision will be
hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
NOTE
• For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
• If warm air is desired at the floor,
set the mode selector switch to the
position.
• In the or position, the
outside air is automatically selected.
The air intake selector switch
cannot be changed to the
recirculated air position.
WARNING
J94S.book Page 10 Saturday, June 23, 2001 1:04 PM

6-16
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
•A new CD may have rough edges on its
inner and outer perimeters. If a disc
with rough edges is used, proper
setting will not be possible and the CD
player/changer will not play the CD.
Remove the rough edges in advance by
using a ball-point pen or pencil as
shown below. To remove the rough
edges, rub the side of the pen or pencil
against the inner and outer perimeter of
the CD.
• When driving over uneven surfaces, the
sound will jump.
• The CD player/changer has been
designed to play CDs bearing the
identification logo as shown. No other
discs can be played. •
Be sure never to touch the signal
surface when handling the CDs. Pick
up a CD by grasping the outer edge or
the edge of the hole and the outer edge.
• Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label).
• Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should
become soiled, gently wipe it with a
soft cloth from the center of the CD to
the edge.
• Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
• CDs, like traditional audio records, are
made of plastic. To avoid warping,
keep the CDs in their cases and do not
store them where they will be exposed
to direct sunlight.
• The CD player/changer ejects the CD if
the CD is inserted upside down. Also
dirty and/or defective CDs may be
ejected.
• 8 cm (3 in) CDs and CD accessories
(e.g. 8 cm disc adapter) cannot be used
in the CD player/changer.
J94S.book Page 16 Saturday, June 23, 2001 1:04 PM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1EGI INJ 30A Fuel injection
system
2 DEFOG 40A Rear window
defroster
3 —— —
4 MAIN 100A For protection of
all circuits
5 IG KEY 30A RADIO,
SUNROOF,
TURN, METER, ENGINE,
POWER
WINDOW,
WIPER fuses,
Ignition system
6 HEATER 40A Heater, Air
conditionerDESCRIPTION FUSE
RATING PROTECTED
COMPONENT
7 BTN 40A TAIL, STOP,
ROOM, DOOR LOCK,
HAZARD,
POWER SEAT fuses
8 COOLING
FA N 30A Cooling fan
9 AD FAN 30A Additional fan
10 (ABS) 60A Antilock brake
system
11 TAIL 15A Taillights,
Parking lights, Dashboard
illumination,
License plate
lights, Switches illumination
12 HORN 15A Horn
J94S.book Page 37 Saturday, June 23, 2001 1:04 PM