light MAZDA MODEL CX-3 2015 Owners Manual (in English)

6–27
Maintenance and Care
Owner Maintenance
Vehicle Engine Control Unit Reset Procedure
NOTE
This procedure is intended for vehicles with SKYACTIV-D 1.5 and vehicles with
SKYACTIV-G 2.0 which the engine oil fl exible maintenance setting is selected.
After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer
perform the initialization (engine oil data resetting) of the recorded value. If the value
recorded by the computer is not initialized, the wrench indicator light may not turn off or it
may turn on earlier than normal.
NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed, and press and hold the selector for
about 5 seconds until the master warning light
fl ashes. 
Selector
3. After the master warning light fl ashes for several seconds, the initialization
is completed.
$9@&;&&%@&EJUJPOJOEC







6–32
Maintenance and Care
Owner Maintenance
Window and Headlight
Washer Fluid
Inspecting Washer Fluid Level
WARNING
Use only windscreen washer fl uid or
plain water in the reservoir:
Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windscreen, it will dirty the windscreen,
affect your visibility, and could result in
an accident.
Inspect fl uid level in the washer fl uid
reservoir; add fl uid if necessary.
E

Use plain water if washer fl uid is
unavailable.
But use only washer fl uid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fl uid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the bonnet's secondary latch
keeps the bonnet from opening when the
primary latch is released.
$9@&;&&%@&EJUJPOJOEC







6–38
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:
 


 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level
A low level of electrolyte fl uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not overfi ll.
Examine the specifi c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead fi rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Dealer for a
battery replacement purchase.
$9@&;&&%@&EJUJPOJOEC







6–39
Maintenance and Care
Owner Maintenance
Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not fl ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
  Make sure the battery is installed
correctly. Battery leakage could
occur if it is not installed correctly.
  When replacing the battery, be
careful not to touch any of the
internal circuitry and electrical
terminals, bend the electrical
terminals, or get dirt in the
transmitter as the transmitter could
be damaged.
  There is the danger of explosion if
the battery is not correctly replaced.
  Dispose of used batteries according
to the following instructions.
 


 Insulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
 


 Never disassemble.



 Never throw the battery into fi re or
water.
 


 Never deform or crush. 

 Replace only with the same type
battery (CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


 The KEY indicator light (green) fl ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


 The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
 


 The system's operational range is
reduced.
Replacing the battery at an Authorised
Mazda Repairer is recommended to
prevent damage to the key. If replacing the
battery by yourself, follow the instruction
below.
Replacing the key battery
1. Press the knob and pull out the
auxiliary key.
Knob
$9@&;&&%@&EJUJPOJOEC







6–40
Maintenance and Care
Owner Maintenance
2. Twist a tape-wrapped fl athead
screwdriver in the direction of the
arrow and open the cover slightly.
Cover
3. Insert the tape-wrapped fl athead
screwdriver into the gap and slide it in
the direction of the arrow.
Cover
Gap
4. Twist the fl athead screwdriver in the
direction of the arrow and remove the
cover.
Cover
5. Remove the battery cap, then remove
the battery.
6. Insert a new battery with the positive
pole facing up, and then cover the
battery with the battery cap.
7. Close the cover.
8. Reinsert the auxiliary key.
$9@&;&&%@&EJUJPOJOEC







*Some models.6–44
Maintenance and Care
Owner Maintenance
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre when this happens.
New treadTread wear indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
(With tyre pressure monitoring system)
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-166 .
Temporary Spare Tyre *
Inspect the temporary spare tyre at least
monthly to make sure it is properly
infl ated and stored.
NOTE
The temporary spare tyre condition
gradually deteriorates even if it has not
been used.
The temporary spare tyre is easier to
handle because of its construction which
is lighter and smaller than a conventional
tyre. This tyre should be used only for an
emergency and only for a short distance.
Use the temporary spare tyre only until
the conventional tyre is repaired, which
should be as soon as possible.
Refer to Tyre on page 9-9 .
CAUTION
  Do not use your temporary spare
tyre rim with a snow tyre or a
conventional tyre. Neither will
properly fi t and could damage both
tyre and rim.
  The temporary spare tyre has a tread
life of less than 5,000 km (3,000
miles). The tread life may be shorter
depending on driving conditions.
  The temporary spare tyre is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tyre with the same type of
temporary spare (page 6-45 ).
$9@&;&&%@&EJUJPOJOEC







*Some models.6–45
Maintenance and Care
Owner Maintenance
Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
CAUTION
A wrong-sized wheel may adversely
affect:
 
 Tyre fi t 
 Wheel and bearing life 
 Ground clearance 
 Snow-chain clearance 
 Speedometer calibration 
 Headlight aim 
 Bumper height 
 Tyre Pressure Monitoring System *
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset
(inset/outset).
Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and fl at spots.
$9@&;&&%@&EJUJPOJOEC







6–46
Maintenance and Care
Owner Maintenance
Light Bulbs
With LED Headlights
With Halogen Headlights
$9@&;&&%@&EJUJPOJOEC







*Some models.6–47
Maintenance and Care
Owner Maintenance
Headlights (Low beam)
Headlights (High beam)
Headlights (High beam)/Running lights *
Running lights/Position lights
Position lights
Front fog lights *
Front direction indicator lights
Side direction indicator lights
Brake lights/Tail lights
Rear direction indicator lights
Tail lights *
Reverse lights
Rear fog light (Left-hand drive model) *
Rear fog light (Right-hand drive model) *
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Overhead lights (Rear)
Luggage compartment light
$9@&;&&%@&EJUJPOJOEC







*Some models.6–48
Maintenance and Care
Owner Maintenance
WARNING
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights (With LED headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with
the unit. We recommend an Authorised
Mazda Repairer when the replacement is
necessary.
Headlights (With halogen headlights)
High-beam bulbs (With running lights)/
Running lights
*
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet.
3. Turn the cover anticlockwise and
remove it.
4. Turn the socket and bulb assembly
anticlockwise and remove it.
$9@&;&&%@&EJUJPOJOEC