keyless MAZDA MODEL CX-3 2015 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 93 of 671
*Some models.3–15
Before Driving
Doors and Locks
NOTE
Auto re-lock function After unlocking with the request
switch, all doors and the liftgate
will automatically lock if any of
the following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights
will fl ash for confi rmation.
The time required for the doors to
lock automatically can be changed.
Refer to Personalisation Features on
page 9-13 .
Opening a door or the liftgate.
Switching the ignition to any
position other than off.
Locking, Unlocking with
Transmitter
All doors and the liftgate can be locked/
unlocked by operating the keyless entry
system transmitter, refer to Keyless Entry
System (page 3-3 ).
Locking, Unlocking with Door-
Lock Switch *
All doors and the liftgate lock
automatically when the lock side is
pressed with all doors and the liftgate
closed.
They all unlock when the unlock side is
pressed.
Lock
Unlock
NOTE
The doors and the liftgate cannot be
locked while any other door or the
liftgate is open.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 98 of 671
3–20
Before Driving
Doors and Locks
CAUTION
Before opening the liftgate, remove
any snow and ice accumulation on
it. Otherwise, the liftgate could close
under the weight of the snow and ice
resulting in injury.
Be careful when opening/closing
the liftgate during strong winds. If a
strong gust blows against the liftgate,
it could close suddenly resulting in
injury.
Fully open the liftgate and make
sure that it stays open. If the liftgate
is only opened partially, it could
slam shut by vibration or wind gusts
resulting in injury.
When loading or unloading luggage
in the luggage compartment, turn
off the engine. Otherwise, you could
get burned by the heat of the exhaust
gas.
Be careful not to apply excessive
force to the damper stay on the
liftgate such as by putting your hand
on the stay. Otherwise, the damper
stay may bend and affect the liftgate
operation.
Damper stay
Opening and Closing the Liftgate
Opening the liftgate with Electric
liftgate opener
Unlock the doors and liftgate, then press
the electric liftgate opener on the liftgate
and raise the liftgate when the latch
releases.
Electric liftgate
opener
NOTE
(With the advanced keyless function)
A locked liftgate can also be opened
while the key is being carried.
When opening the liftgate with the
doors and the liftgate locked, it may
require a few seconds for the liftgate
latch to release after the electric
liftgate opener is pressed.
The liftgate can be closed when the
doors are locked with the key left
in the vehicle. However, to prevent
locking the key in the vehicle, the
liftgate can be opened by pressing
the electric liftgate opener. If the
liftgate cannot be opened despite
doing this procedure, press the
electric liftgate opener to fully open
the liftgate after pushing the liftgate
completely closed.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 121 of 671
3–43
Before Driving
Security System
Operation
Siren triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights fl ash for about
30 seconds when the system is triggered
by any one of the following:
Unlocking a door with an inside door-
lock knob.
Forcing open a door, the bonnet or the
liftgate.
Opening the bonnet by operating the
bonnet release handle.
Switching the ignition ON without using
the push button start.
(With the intrusion sensor)
The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
(With the intrusion sensor)
Disconnecting the battery terminal (the
hazard warning lights do not fl ash).
The system will be triggered about 10
times.
NOTE
The liftgate does not open while the
theft-deterrent system is operating.
If the battery goes dead while the
theft-deterrent system is armed, the
siren will activate and the hazard
warning lights will fl ash when the
battery is charged or replaced.
How to Arm the System
1. Close the windows securely.
NOTE
(With the intrusion sensor)
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion/Tilt
Sensor on page 3-44 .
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 122 of 671
*Some models.3–44
Before Driving
Security System
NOTE
The theft deterrent system can also
be armed by activating the auto
relock function with all the doors, the
liftgate and the bonnet closed.
Refer to Transmitter on page 3-4 . The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
Unlocking any door.
Opening any door.
Opening the bonnet.
Switching the ignition ON.
(With the advanced keyless
function)
Pressing the electric liftgate opener
while the key is being carried.
To rearm the system, do the arming
procedure again.
When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
fl ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
Hanging small objects/accessories in
the vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
Parking in an area where there is strong
vibration or loud noise.
When using a high pressure or automatic
car wash.
Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
Doors are locked with a window or the
sunroof* left open.
An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the liftgate remains closed
for 30 seconds, all the doors and the
liftgate automatically re-lock and the
theft deterrent system arms even if a
window and the sunroof
* is left open.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 123 of 671
3–45
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will fl ash three
times.
NOTE
To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
Pressing the unlock button on the
transmitter.
Starting the engine with the push button
start.
(With the advanced keyless function)
Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
Pressing the unlock button on the
transmitter.
Starting the engine with the push button
start.
(With the advanced keyless function)
Pressing a request switch on the doors.
Pressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will fl ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 145 of 671
4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-36 ).
NOTE
(SKYACTIV-G 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
The key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
The engine can be started when the
push button start is pressed from off,
ACC, or ON.
The push button start system
functions (function which can start
the engine by only carrying the
key) can be deactivated to prevent
any possible adverse effect on a
user wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable
to start the engine by carrying the
key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 154 of 671
4–14
When Driving
Start/Stop Engine
Automatic transaxle
1. Engine idling stops when the brake pedal is depressed while the vehicle is driven (except
for driving in the R or M position second gear fi xed mode) and the vehicle is stopped.
2. The engine restarts automatically when the brake pedal is released with the selector lever
in the D or M position (not in second gear fi xed mode).
3. If the selector lever is in the N or P position, the engine does not restart when the brake
pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear fi xed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depressed when shifting the
selector lever while engine idling is stopped.)
Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
(SKYACTIV-G 2.0)
The engine is warmed up.
(SKYACTIV-D 1.5)
The engine is not cold.
The fuel injection amount learning, which is performed periodically and automatically,
is not being performed.
The engine has been started and the vehicle is driven for a certain period.
The engine is started with the bonnet closed.
The battery is in good condition.
All doors, liftgate, and bonnet are closed.
The driver's seat belt is fastened.
The air conditioner is not operating with the airfl ow mode dial in the position (A/C
ON).
(Automatic air-conditioning)
The temperature setting dial for the air conditioning is set to a position other than
maximum cooling (A/C ON).
The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
The i-stop warning light (amber) is not turned on/fl ashing.
The keyless entry & push button start system functions are normal.
The brake vacuum is suffi ciently high.
The steering wheel is not being operated.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 470 of 671
5–14 8
Interior Features
Interior Equipment
The overhead lights turn on for about 15
seconds when the ignition is switched
off with the overhead light switch in the
DOOR position.
The overhead lights turn off immediately
in the following cases:
The ignition is switched on and all doors
are closed.
The driver's door is locked.
NOTE
Battery saver If any door is left open with the
overhead light switch in the DOOR
position, or the liftgate is left open,
the overhead light or luggage
compartment light turns off after
about 30 minutes to prevent battery
depletion.
To prevent battery depletion, if the
interior lights remain turned on (the
interior light switch is in the ON
position or an interior light is turned
on by pressing the lens of the interior
light), they turn off automatically
under the following conditions:
No operations are done for about
30 minutes after the ignition is
switched off.
When the LOCK button on the key
is pressed or the request switch
is pressed to lock the doors on
vehicles with the advanced keyless
function after the ignition is
switched off (interior lights turn off
a few seconds).
In addition, if the following
operations are performed after
turning the interior lights off, they
will turn on again.
The ignition is switched to a
position other than OFF.
A door is opened.
A door is unlocked.
The operation of the illuminated
entry system can be changed.
Refer to Personalisation Features on
page 9-13 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 587 of 671
*Some models.7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Flashing)
Tyre Pressure
Monitoring System
Warning Light
*
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light fl ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
WARNING
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the tyre
pressure warning beep sound is heard, decrease vehicle speed immediately and avoid
sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a fl at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.
Do not ignore the TPMS Warning Light: Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.
(Red)
(Illuminate)
KEY Warning Light If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) fl ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 597 of 671
*Some models.7–51
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
NOTE
Placing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function
to operate depending on the weight
of the item.
To allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger
seat. The sensor may not function
properly because the additional
seat cushion could cause sensor
interference.
When a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Rear seat
*
The warning beep only sounds if a seat
belt is unfastened after being fastened.
Ignition Not Switched Off (STOP)
Warning Beep
If the driver's door is opened while
the ignition is switched to ACC, a
continuous beep sound will be heard to
notify the driver that the ignition has not
been switched off (STOP). Left in this
condition, the keyless entry system will
not operate, the car cannot be locked, and
the battery power will be depleted.
Key Removed from Vehicle
Warning Beep
A beep sound will be heard 6 times and
the KEY warning light (red) will fl ash
continuously if the ignition has not been
switched off, all the doors are closed, and
the key is removed from the vehicle. This
is to notify the driver that the key has been
removed from the vehicle and the ignition
has not been switched off.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key
is carried together with a metal object
or it is placed in a poor signal reception
area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with a door
open or ajar or the ignition has not been
switched off while the key is being carried,
a beep will be heard for about 2 seconds
to indicate that the doors and the liftgate
cannot be locked.
$ 9 @ & ; & & % @ & E J U J P O J O E C