low beam MAZDA MODEL CX-3 2015 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 282 of 671
4–142
When Driving
i-ACTIVSENSE
NOTE
The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam refl ected off the refl ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
Refl ection of the laser is poor due to the shape of the vehicle ahead.
The vehicle ahead is signifi cantly dirty.
Under bad weather condition, such as rain, fog and snow.
The window washer is being used or the windscreen wipers are not used when it's
raining.
The windscreen is dirty.
The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
Trucks with low loading platforms and vehicles with an extremely low or high
profi le.
Vehicles with certain shapes such as a vehicle carrier.
Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
Heavy luggage is loaded in the luggage compartment or on the rear seat.
If there is the possibility of partial contact with a vehicle ahead.
When driving on continuously curving roads, and entering and exiting exits.
Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front) .
Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
When towing a malfunctioning vehicle.
When driving with tyres having signifi cantly different wear.
In the following cases, the laser sensor (front) may inadvertently determine that there
is a vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
Objects on the road at the entrance to a curve.
Vehicles passing in the opposite lane while making a curve.
Metal objects, bumps, or protruding objects on the road.
When passing through a toll gate equipped with a bar.
When passing under a vinyl curtain or fl ag.
Plastic objects such as pylons.
Two-wheeled vehicles, pedestrians, animals or standing trees.
(Manual transaxle) If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed,
the engine stops.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 288 of 671
*Some models.4–14 8
When Driving
i-ACTIVSENSE
Forward Sensing Camera (FSC) *
Your vehicle is equipped with a Forward Sensing Camera (FSC). The Forward Sensing
Camera (FSC) is positioned near the rearview mirror and used by the following systems.
High Beam Control System (HBC)
Lane Departure Warning System (LDWS)
Smart Brake Support (SBS)
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) determines the conditions ahead of the vehicle while
travelling at night and detects traffi c lanes. The distance in which the Forward Sensing
Camera (FSC) can detect objects varies depending on the surrounding conditions.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 289 of 671
4–149
When Driving
i-ACTIVSENSE
CAUTION
Do not apply accessories, stickers or fi lm to the windscreen near the Forward Sensing
Camera (FSC).
If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will
cause the system to not operate correctly. Consequently, each system may not operate
normally which could lead to an unexpected accident.
Do not disassemble or modify the Forward Sensing Camera (FSC). Disassembly or modifi cation of the Forward Sensing Camera (FSC) will cause a
malfunction or mistaken operation. Consequently, each system may not operate
normally which could lead to an unexpected accident.
Heed the following cautions to assure the correct operation of the Forward Sensing
Camera (FSC).
The direction of the Forward Sensing Camera (FSC) has been fi nely adjusted,
therefore do not change the installation position or remove the Forward Sensing
Camera (FSC).
Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get
dirty.
Do not remove the Forward Sensing Camera (FSC) cover.
Do not place objects on the instrument panel which refl ect light.
Always keep the windscreen glass around the camera clean by removing dirt or
fogging. Use the windscreen defroster to remove fogging on the windscreen.
Consult an expert repairer, we recommend an Authorised Mazda Repairer regarding
cleaning the interior side of the windscreen around the Forward Sensing Camera
(FSC).
Consult an expert repairer, we recommend an Authorised Mazda Repairer before
performing repairs around the Forward Sensing Camera (FSC).
The Forward Sensing Camera (FSC) is installed to the windscreen. Consult an expert
repairer, we recommend an Authorised Mazda Repairer for windscreen repair and
replacement.
When performing repairs around the rearview mirror, consult an expert repairer, we
recommend an Authorised Mazda Repairer.
Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area
around it. If strong force is applied, stop using the Lane Departure Warning System
(LDWS), the High Beam Control System (HBC), and the Smart Brake Support
(SBS) and consult an expert repairer, we recommend an Authorised Mazda Repairer.
The direction in which the Forward Sensing Camera (FSC) is pointed has been fi nely
adjusted. Do not change the installation position of the Forward Sensing Camera
(FSC) or remove it. Otherwise, it could result in damage or malfunction.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 290 of 671
4–150
When Driving
i-ACTIVSENSE
NOTE
In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
The height of the vehicle ahead is low.
You drive your vehicle at the same speed as the vehicle ahead.
Headlights are not turned on during the night or when going through a tunnel.
In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
When driving next to walls with no patterning (including fences and longitudinally
striped walls).
The tail lights of the vehicle ahead are turned off.
A vehicle is outside the illumination range of the headlights.
The vehicle is making a sharp curve, or ascending or descending a steep slope.
Entering or exiting a tunnel.
Heavy luggage is loaded causing the vehicle to tilt.
Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
There are many light emitters on the vehicle ahead.
When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off at nighttime.
The vehicle ahead has a special shape.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 310 of 671
4–170
When Driving
Rear View Monitor
Displayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
Garnish
Bumper
(Actual view)
Object
NOTE
The displayable range varies depending on the vehicle and road conditions.
The displayable range is limited. Objects under the bumper or around the bumper ends
cannot be displayed.
The distance appearing in the displayed image is different from the actual distance
because the rear view parking camera is equipped with a specifi c lens.
Some optionally installed vehicle accessories may be picked up by the camera. Do not
install any optional parts that can interfere with the camera view, such as illuminating
parts or parts made of refl ective material.
It may be diffi cult to see the display under the following conditions, however, it does
not indicate a malfunction.
In darkened areas.
When the temperature around the lens is high/low.
When the camera is wet such as on a rainy day or during periods of high humidity.
When foreign material such as mud is stuck around the camera.
When the camera lens refl ects sunlight or headlight beams.
Image display may be delayed if the temperature around the camera is low.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 525 of 671
*Some models.6–47
Maintenance and Care
Owner Maintenance
Headlights (Low beam)
Headlights (High beam)
Headlights (High beam)/Running lights *
Running lights/Position lights
Position lights
Front fog lights *
Front direction indicator lights
Side direction indicator lights
Brake lights/Tail lights
Rear direction indicator lights
Tail lights *
Reverse lights
Rear fog light (Left-hand drive model) *
Rear fog light (Right-hand drive model) *
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Overhead lights (Rear)
Luggage compartment light
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 527 of 671
6–49
Maintenance and Care
Owner Maintenance
5. Install the new bulb in the reverse order
of the removal procedure.
High-beam bulbs (Without running
lights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
Low-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the bonnet.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse order
of the removal procedure.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 588 of 671
*Some models.7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Illuminate)
Lane Departure
Warning System
(LDWS) Warning
Light
*
The warning light remains turned on if there is a problem with the system. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The LDWS does not operate when the warning light illuminates.
CAUTION
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
When the light remains turned on while driving the vehicle.
When the system is cancelled automatically, the light turns on. Normally, the system
restores automatically and the light turns off, however, if the light remains turned on,
there may be a problem with the system.
The light does not illuminate when the ignition is switched ON. Always use tyres for all wheels that are of the specifi ed size, and the same
manufacture, brand, and tread pattern. In addition, do not use tyres with signifi cantly
different wear patterns on the same vehicle. If such improper tyres are used, the
LDWS may not operate normally.
When an emergency spare tyre is used, the system may not operate normally.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
The light remains turned on if there is a problem with the system. Have your vehicle
inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
If the windscreen area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
LED Headlight
Warning Light *
This light illuminates if there is a malfunction in the LED headlight. Have your vehicle
inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light turns on if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on.
Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda
Repairer.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 634 of 671
9–8
Specifi cations
Specifi cations
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1 (SAE)
Headlights Halogen
headlights High beam With running
lights 15/55
*2 H15 (—)
Without
running lights 60 HB3 (9005)
Low beam 55 H11 (H11)
LED
headlights High beam LED
*3 — (—)
Low beam LED *3 — (—)
Running lights With halogen headlights * 15/55 *4 H15 (—)
With LED headlights LED *3 — (—)
Position lights With halogen headlights 5 W5W (—)
With LED headlights LED
*3 — (—)
Front direction indicator lights 21 PY21W (—)
Front fog lights
* LED *3 — (—)
Side direction indicator lights LED *3 — (—)
High-mount brake light LED *3 — (—)
Rear direction indicator lights 21 WY21W (7443NA)
Brake lights/Tail lights With halogen headlights 21/5 W21/5W (7443)
With LED headlights LED
*3 — (—)
Tail lights (With LED headlights) LED *3 — (—)
Reverse lights 16 W16W (921)
Rear fog light
* 21 W21W (7440)
Number plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 Double-fi lament light bulb, however, only 55 W fi lament bulb is used in the headlights (high beam).
*3 LED is the abbreviation for Light Emitting Diode.
*4 Double-fi lament light bulb, however, only 15 W fi lament bulb is used in the running lights.
Interior light
Light bulb Category
Wattage UNECE *1
Luggage compartment light 5 —
Overhead lights (Front)/Map lights 8 —
Overhead light (Rear) 10 —
*1 UNECE stands for United Nations Economic Commission for Europe.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 643 of 671
9–17
Specifi cations
Personalisation Features
Item Feature Factory
Setting Available
Settings Settings change method
Vehicle Running
lights
Refer to
Running
Lights on
page
4-64 . The function of the
running lights can be
changed. On On/
Off
Refer to
Settings
on page
5-65 . —
Auto-light
control
Refer to
Headlights
on page
4-58 . The headlight
illumination on/
off timing based on
surrounding lightness/
darkness can be
changed. Medium High/
Med. High/
Medium/
Med. Low/
Low
Refer to
Settings
on page
5-65 . —
High Beam
Control
System
(HBC)
Refer to
High Beam
Control
System
(HBC) on
page
4-102 . The High Beam
Control System
(HBC) function can be
changed.
*1
On On/Off Refer to
Settings
on page
5-65 . —
Adaptive
Front
Lighting
System
(AFS)
Refer to
Adaptive
Front
Lighting
System
(AFS) on
page
4-101 . The Adaptive Front
Lighting System
(AFS) function can be
changed.
*1
On On/Off Refer to
Settings
on page
5-65 . —
Lights-on
reminder
Refer to
Lights-On
Reminder
on page
7-50 . The volume of the
lights-on reminder
warning alarm can be
changed. High High/Low/Off
Refer to
Settings
on page
5-65 . —
$ 9 @ & ; & & % @ & E J U J P O J O E C