display MAZDA MODEL CX-3 2015 (in English) Workshop Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 275 of 671
4–135
When Driving
i-ACTIVSENSE
Adjustable Speed Limiter Display
The setting status of the adjustable speed limiter is displayed in the active driving display or
the display in the instrument cluster.
Stand-by display
Displays when the speed limiter switch is operated and the system is turned on.
Turns off when the system is turned off.
Active Driving Display Display in the instrument cluster
Setting display
Displays when the SET
/ SET switch is operated and the speed is set.
Active Driving Display Display in the instrument cluster
Cancel display
Displays when any of the following operations is done and the system is temporarily
cancelled.
Cancel switch is operated
Accelerator pedal is strongly depressed
Active Driving Display Display in the instrument cluster
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 276 of 671
4–136
When Driving
i-ACTIVSENSE
Adjustable Speed Limiter Main Indicator Light (Amber)/Adjustable Speed
Limiter Set Indicator Light (Green)
The indicator light has two colours.
Adjustable speed limiter main indicator light (amber)
The indicator light illuminates amber when the speed limiter switch is pressed and the
adjustable speed limiter is activated.
Adjustable speed limiter set indicator light (green)
The indicator light illuminates green when a speed has been set.
Speed Limiter Warning Beep
If the vehicle speed exceeds the set speed by about 3 km/h (2 mph) or more, a warning
sound operates continuously and the adjustable speed limiter display fl ashes at the same
time. The warning sound operates and the display fl ashes until the vehicle speed decreases
to the set speed or less.
Verify the safety of the surrounding area and adjust the vehicle speed by applying the
brakes. Additionally, keep a safe distance from the vehicles behind you.
Active Driving Display Display in the instrument cluster
CAUTION
If the set speed is set lower than the current vehicle speed by pressing the SET or
RESUME switch, the warning beep is not activated for about 30 seconds even if the
vehicle speed is faster than the newly set speed by 3 km/h (2 mph). Be careful not to drive
over the set speed.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 277 of 671
4–137
When Driving
i-ACTIVSENSE
NOTE
When the system is temporarily cancelled by depressing the accelerator pedal fully, the
adjustable speed limiter display shows the cancel display. If the vehicle speed exceeds the
set speed by about 3 km/h (2 mph) or more while the cancel display is displayed, the set
speed display fl ashes but the warning sound is not operated.
Turning the System On/Off
Press the speed limiter switch to turn the system on. The adjustable speed limiter display is
displayed.
To turn the system off, press the speed limiter switch while the adjustable speed limiter is
displayed. The adjustable speed limiter display turns off.
Setting the System
WARNING
Always verify the safety of the surrounding area when setting the adjustable speed
limiter:
If the speed is set lower than the current vehicle speed, the vehicle speed is decreased to
the set speed. Verify the safety of the surrounding area and keep a safe distance between
vehicles ahead and behind you.
1. Press the speed limiter switch to turn the system on.
2. Press the SET
or SET to set the speed. When the current vehicle speed is 30 km/h
(20 mph) or more, the speed is set to the current vehicle speed. When the current vehicle
speed is less than 30 km/h (20 mph), the speed is set to 30 km/h (20 mph).
3. To increase the set speed, press the SET
switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) increments. The set speed can also be adjusted in about 1
km/h (1 mph) increments by pressing the SET
switch momentary. For example, the set
speed increases about 4 km/h (4 mph) by pressing the SET
switch 4 times.
4. To decrease the set speed, press the SET
switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) decrements. The set speed can also be adjusted in about 1
km/h (1 mph) increments by pressing the SET
switch momentary. For example, the set
speed decreases about 4 km/h (4 mph) by pressing the SET
switch 4 times.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 278 of 671
4–138
When Driving
i-ACTIVSENSE
NOTE
The system does not operate when the cruise control/Mazda Radar Cruise Control
(MRCC) is on.
The system is temporarily cancelled when the vehicle is accelerated by depressing the
accelerator pedal strongly, however, it resumes when the vehicle speed decreases to the
set speed or less.
The vehicle speed may exceed the set speed on a down slope.
Temporarily Cancelling the System
The system is temporarily cancelled (stand-by status) when any of the following operations
is done while the adjustable speed limiter is displayed.
CANCEL switch is pressed
Accelerator pedal is strongly depressed
Press the RESUME switch to resume the operation at the previous set speed. The adjustable
speed limiter display remains displayed.
NOTE
The set speed can be set by pressing the SET or SET switch while the system is in
stand-by status.
The adjustable speed limiter is not cancelled by depressing the brake pedal.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 283 of 671
*Some models.4–14 3
When Driving
i-ACTIVSENSE
NOTE
When the system operates, the user is notifi ed by the fl ashing Smart City Brake
Support (SCBS) indicator light (red) and the active driving display * . The Smart City Brake Support (SCBS) warning light (amber) turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-37 .
Smart City Brake Support (SCBS)
Indicator Light (Red)
If the Smart City Brake Support (SCBS) is
operating, the indicator light (red) fl ashes.
Automatic Brake Operation
Display (Vehicles With Active
Driving Display)
“SCBS Automatic Brake” is displayed in
the active driving display while the SCBS
brakes or the brake assist (SCBS brake
assist) is operating.
NOTE
The collision warning beep sounds
intermittently while the SCBS brake
or brake assist (SCBS brake assist) is
operating.
If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds
one time after about 2 seconds and
the SCBS brake is automatically
released.
Stopping The Smart City Brake
Support (SCBS) System Operation
The Smart City Brake Support (SCBS)
system can be temporarily deactivated.
When the Smart City Brake Support
(SCBS) system is turned off, the Smart
City Brake Support (SCBS) OFF indicator
light turns on.
When the engine is restarted, the system
becomes operational.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 286 of 671
4–14 6
When Driving
i-ACTIVSENSE
NOTE
The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
The ignition is switched ON.
The Smart Brake Support (SBS) system is on.
The vehicle speed is about 15 km/h or faster (10 mph or faster).
The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
The Dynamic Stability Control (DSC) is not operating.
The Smart Brake Support (SBS) system may not operate under the following
conditions:
If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.
The vehicle is driven at the same speed as the vehicle ahead.
The accelerator pedal is depressed.
The brake pedal is depressed.
The steering wheel is being operated.
The selector lever is being operated.
The direction indicator is being used.
When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off.
When warnings and messages, such as a dirty windscreen, related to the Forward
Sensing Camera (FSC)/laser sensor (front) are being displayed in the centre display.
Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction,
and operate the Smart Brake Support (SBS) system.
Objects on the road at the entrance to a curve (including guardrails and snow banks).
A vehicle appears in the opposite lane while cornering or rounding a curve.
When crossing a narrow bridge.
When passing under a low gate or through a tunnel or narrow gate.
When entering an underground parking area.
Metal objects, bumps, or protruding objects on the road.
If you suddenly come close to a vehicle ahead.
When driving in areas where there is high grass or forage.
Two-wheeled vehicles such as motorbikes or bicycles.
Pedestrians or non-metallic objects such as standing trees.
When the system operates, the user is notifi ed by the fl ashing Smart Brake Support
(SBS) indicator light (red) and the active driving display.
The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction. Refer to Warning/Indicator Lights on page 4-36 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 287 of 671
4–147
When Driving
i-ACTIVSENSE
Smart Brake Support (SBS)
Indicator Light (Red)
If the Smart Brake Support (SBS) is
operating, the indicator light (red) fl ashes.
Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the active driving display.
Stopping The Smart Brake
Support (SBS) System Operation
The Smart Brake Support (SBS) system
can be temporarily deactivated.
Refer to Personalisation Features on page
9-13 .
When the Smart Brake Support (SBS)
system is turned off, the Smart Brake
Support (SBS) OFF indicator light turns
on.
When the engine is restarted, the system
becomes operational.
NOTE
If the Smart Brake Support (SBS)
system operation is turned off, the Smart
City Brake Support (SCBS) system
operation is turned off simultaneously.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 291 of 671
*Some models.4–151
When Driving
i-ACTIVSENSE
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
Mazda Radar Cruise Control (MRCC)
Distance Recognition Support System (DRSS)
Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves refl ected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mounted behind the front emblem.
Radar sensor (front)
If the Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light (amber)
is illuminated, the area around the radar sensor may be dirty. Refer to “Warning Guidance”
in the centre display (Type C/D audio).
Refer to If a Warning Light Turns On or Flashes on page 7-35 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 300 of 671
4–160
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
The cruise control speed setting
cannot be performed under the
following conditions:
(Automatic transaxle)
The selector lever is in the P or N
position.
(Manual transaxle)
The shift lever is in the neutral
position.
The parking brake is applied.
(Vehicles with adjustable speed
limiter)
The ON/OFF switch for the
adjustable speed limiter is pressed.
Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 301 of 671
4–161
When Driving
Cruise Control
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere with
or change the set speed. Take your foot
off the accelerator to return to the set
speed.
To Decrease Cruising Speed
Press the SET switch and hold it. The
vehicle will gradually slow.
Release the switch at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To Resume Cruising Speed at
More Than 25 km/h (16 mph)
If some other method besides the OFF
switch was used to cancel cruising speed
(such as applying the brake pedal) and the
system is still activated, the most recent
set speed will automatically resume when
the RESUME switch is pressed.
If vehicle speed is below 25 km/h (16
mph), increase the vehicle speed up to
25 km/h (16 mph) or more and press the
RESUME switch.
To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
Slightly depress the brake pedal.
(Manual transaxle)
Depress the clutch pedal.
Press the CANCEL switch.
If the RESUME switch is pressed when
the vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
If any of the following conditions
occur, the cruise control system is
temporarily cancelled.
The parking brake is applied.
(Vehicles with adjustable speed
limiter)
The ON/OFF switch for the
adjustable speed limiter is pressed.
(Automatic transaxle)
The selector lever is in the P or N
position.
(Manual transaxle)
The shift lever is in the neutral
position.
When the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
(Automatic transaxle) The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from
D to M position). Therefore, engine
braking will not be applied even
if the transaxle is shifted down
to a lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
$ 9 @ & ; & & % @ & E J U J P O J O E C