ignition MAZDA MODEL CX-3 2015 (in English) Manual Online
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 268 of 671
4–128
When Driving
i-ACTIVSENSE
Setting the System
To Activate
With adjustable speed limiter
To activate the system, press the ON/OFF switch.
Without adjustable speed limiter
To activate the system, press the ON switch.
ON/OFF switch
OFF switch ON switch Without Adjustable Speed Limiter With Adjustable Speed Limiter
CANCEL switch CANCEL switch
Switch SwitchRESUME
switchRESUME
switch
Switch Switch
SET+/SET- switch SET+/SET- switch
When the ON switch is pressed, the vehicle speed and the distance between vehicles while
in headway control can be set. The Mazda Radar Cruise Control (MRCC) indication is
shown in the display of the instrument cluster.
NOTE
When the ignition is switched to ACC or OFF while the Mazda Radar Cruise Control
(MRCC) is ON, the Mazda Radar Cruise Control (MRCC) remains ON automatically.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 270 of 671
4–130
When Driving
i-ACTIVSENSE
How to Set the Distance Between
Vehicles During Headway Control
The distance between vehicles is set to a
shorter distance each time the
switch is
pressed. The distance between vehicles is
set to a longer distance by pressing the
switch. The distance-between-vehicles can
be set to 4 levels; Long, medium, short,
and extremely short distance.
Distance-between-
vehicles guideline
(at 80 km/h (50 mph)
vehicle speed) Indication on display
Long (about 50 m (164
ft))
Medium (about 40 m
(131 ft))
Short (about 30 m (98
ft))
Extremely short (about
25 m (82 ft))
NOTE
The distance between vehicles differs
depending on the vehicle speed, and
the slower the vehicle speed, the
shorter the distance.
When the ignition is switched
to ACC or OFF and then the
engine is started again, the system
automatically sets the distance
between vehicles to the previous
setting.
Changing the Set Vehicle Speed
Changing the set vehicle speed using the
SET switch
Press the SET
switch to accelerate.
Press the SET
switch to decelerate.
The set vehicle speed changes as follows
each time the SET switch is pressed.
European
models Except
European
models
Short press 1 km/h (1 mph) 5 km/h (5 mph)
Long press 10 km/h (5 mph)
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 286 of 671
4–14 6
When Driving
i-ACTIVSENSE
NOTE
The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
The ignition is switched ON.
The Smart Brake Support (SBS) system is on.
The vehicle speed is about 15 km/h or faster (10 mph or faster).
The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
The Dynamic Stability Control (DSC) is not operating.
The Smart Brake Support (SBS) system may not operate under the following
conditions:
If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.
The vehicle is driven at the same speed as the vehicle ahead.
The accelerator pedal is depressed.
The brake pedal is depressed.
The steering wheel is being operated.
The selector lever is being operated.
The direction indicator is being used.
When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off.
When warnings and messages, such as a dirty windscreen, related to the Forward
Sensing Camera (FSC)/laser sensor (front) are being displayed in the centre display.
Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction,
and operate the Smart Brake Support (SBS) system.
Objects on the road at the entrance to a curve (including guardrails and snow banks).
A vehicle appears in the opposite lane while cornering or rounding a curve.
When crossing a narrow bridge.
When passing under a low gate or through a tunnel or narrow gate.
When entering an underground parking area.
Metal objects, bumps, or protruding objects on the road.
If you suddenly come close to a vehicle ahead.
When driving in areas where there is high grass or forage.
Two-wheeled vehicles such as motorbikes or bicycles.
Pedestrians or non-metallic objects such as standing trees.
When the system operates, the user is notifi ed by the fl ashing Smart Brake Support
(SBS) indicator light (red) and the active driving display.
The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction. Refer to Warning/Indicator Lights on page 4-36 .
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 299 of 671
4–159
When Driving
Cruise Control
Cruise Main Indicator Light
(Amber)/Cruise Set Indicator
Light (Green)
The indicator light has two colours.
Cruise Main Indicator Light (Amber)
The indicator light illuminates amber
when the cruise control system is
activated.
Cruise Set Indicator Light (Green)
The indicator light illuminates green when
a cruising speed has been set.
Activation/Deactivation
With adjustable speed limiter
To activate the system, press the ON/OFF
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the switch
again.
The cruise main indicator light (amber)
turns off.
Without adjustable speed limiter
To activate the system, press the ON
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the OFF
switch.
The cruise main indicator light (amber)
turns off.
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as
the cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the cruise control
system operable, the system will be
operable when the ignition is switched
ON the next time.
To Set Speed
1 . (With adjustable speed limiter)
Activate the cruise control system
by pressing the ON/OFF switch. The
cruise main indicator light (Amber)
illuminates.
(Without adjustable speed limiter)
Activate the cruise control system
by pressing the ON switch. The
cruise main indicator light (Amber)
illuminates.
2. Accelerate to the desired speed, which
must be more than 25 km/h (16 mph).
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 306 of 671
4–16 6
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
A tyre pressure is adjusted.
Tyre rotation is performed.
A tyre or wheel is replaced.
The battery is replaced or completely
drained.
The tyre pressure monitoring system
warning light is illuminated.
Initialization method
1. Park the car in a safe place and fi rmly
apply the parking brake.
2. Let the tyres cool, then adjust the tyre
pressure of all four (4) tyres to the
specifi ed pressure indicated on the tyre
pressure label located on the door jamb
of the driver's door (door open).
Refer to Tyres on page 9-9 .
3. Switch the ignition ON.
4. While the vehicle is parked, press
and hold the tyre pressure monitoring
system set switch and verify that
the tyre pressure monitoring system
warning light in the instrument cluster
fl ashes twice and a beep sound is heard
once.
CAUTION
If the system initialization is performed
without adjusting the tyre pressure, the
system cannot detect the normal tyre
pressure and it may not illuminate the
tyre pressure monitoring system warning
light even if a tyre pressure is low, or
it may illuminate the light even if the
pressures are normal.
Adjust the tyre pressure on all four
tyres and initialize the system when
the warning light is turned on. If the
warning light turns on for a reason other
than a fl at tyre, the tyre pressure of all
four tyres may have decreased naturally.
The system initialization will not be
performed if the switch is pressed while
the vehicle is being driven.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 309 of 671
4–169
When Driving
Rear View Monitor
NOTE
If water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it
cannot be wiped off, use a mild detergent.
If the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view
monitor may not operate correctly.
When replacing the tyres, consult an expert repairer, we recommend an Authorised
Mazda Repairer. Replacing the tyres could result in deviation of the guide lines which
appear on the display.
If the vehicle's front, side, or rear has been involved in a collision, the alignment of
the rear view parking camera (location, installation angle) may have deviated. Always
consult an expert repairer, we recommend an Authorised Mazda Repairer to have the
vehicle inspected.
If “No Video Signal Available” is indicated in the display, there could be a problem
with the camera. Have your vehicle inspected at an expert repairer, we recommend an
Authorised Mazda Repairer.
Rear View Parking Camera Location
Rear view parking camera
Switching to the Rear View Monitor Display
Shift the shift lever to R with the ignition switched ON to switch the display to the rear view
monitor display.
NOTE
When the shift lever is shifted from R to another shift lever position, the screen returns to
the previous display.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 319 of 671
4–179
When Driving
Parking Sensor System
Sensor Detection Range
The sensors detect obstructions within the following range.
Rear sensor detection range Rear corner sensor detection rangeB AA: About 50 cm (About 19 in)
B: About 150 cm (About 59.0 in)
Park Assist Sensor System Operation
When the ignition is switched ON and the shift lever is shifted to the reverse (R), the beep
sound activates and the system is enabled for use.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 324 of 671
5–2
Interior Features
Air-Conditioning System
Operating Tips
Operate the air-conditioning system with
the engine running.
To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time with the
ignition switched ON when the engine is
not running.
(With i-stop)
The airfl ow amount may decrease
slightly while the i-stop function is
operating.
Clear all obstructions such as leaves,
snow and ice from the bonnet and the
air inlet in the cowl grille to improve the
system effi ciency.
Use the air-conditioning system to defog
the windows and dehumidify the air.
The recirculate mode should be used
when driving through tunnels or while in
a traffi c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
Use the outside air position for
ventilation or windscreen defrosting.
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the air-conditioning system.
Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
effi cient.
The refrigerant specifi cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before refi lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
For details, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Label
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 350 of 671
5–28
Interior Features
Audio System
Power/Volume/Sound Controls
Power/Volume/Audio control dial
The figure is an example showing the type A unit.Menu button Audio display
Power ON/OFF
Switch the ignition to ACC or ON. Press
the power/volume dial to turn the audio
system on. Press the power/volume dial
again to turn the audio system off.
Volume adjustment
To adjust the volume, turn the power/
volume dial. Turn the power/volume
dial clockwise to increase volume,
anticlockwise to decrease it. Audio sound adjustment
1. Press the menu button (
) to select
the function. The selected function will
be indicated.
2. Turn the audio control dial to adjust the
selected functions as follows:
Indication Setting value Turn
Anticlockwise Turn
Clockwise
AF
*1
(Setting Alternative
Frequency (AF)) Off On
REG
*1
(Setting Regional
Programme (REG)) Off On
ALC
(Automatic volume
adjustment) Level decrease Level
increase
BASS
(Low pitch sound) Decrease bass Increase
bass
TREB
(Treble sound) Decrease treble Increase
treble
FADE
(Front/back volume
balance) Shift the sound
to the front Shift the
sound to
the rear
BAL
(Left/right volume
balance) Shift the sound
to the left Shift the
sound to
the right
BEEP
(Audio operation
sound) Off On
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 352 of 671
5–30
Interior Features
Audio System
Clock
Audio display Audio control dial
Hour/Minute set switch:00 button
Menu button Clock button
The figure is an example showing the type A unit.
Setting the time
The clock can be set at any time when the
ignition is switched to ACC or ON.
1. To adjust the time, press the clock
button (
) for about 2 seconds until
a beep is heard.
2. The clock's current time will fl ash.
Time adjustment
To adjust the time, press the hour/
minute set button (
,) while the
clock's current time is fl ashing.
The hours advance while the hour set
button (
) is pressed. The minutes
advance while the minute set button
(
) is pressed.
3. Press the clock button (
) again to
start the clock.
Time resetting
1. Press the clock button (
) for about
2 seconds until a beep is heard.
2. Press the :00 button ( 1 ).
3. When the button is pressed, the time
will be reset as follows:
(Example)
12:01—12:29:12:00
12:30—12:59:1:00
NOTE
When the :00 button ( 1 ) is pressed,
the seconds will start at “ 00 ”.
Switching between 12 and 24-hour
clock time:
Press the menu button ()
several times until 12 and 24-hour
clock time are displayed. Turn the
audio control dial in either direction,
select the desired clock setting while
the preferred clock time is fl ashing.
$ 9 @ & ; & & % @ & E J U J P O J O E C