engine overheat MAZDA MODEL CX-3 2015 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 127 of 671
3–49
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, fl ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
Have the proper ratio of antifreeze in the
radiator.
Refer to Engine Coolant on page 6-29 .
Inspect the battery and its leads. Cold
reduces battery capacity.
Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
Inspect the ignition system for damage
and loose connections.
Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-32 ).
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 139 of 671
3–61
Before Driving
Towing
When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.
Parking
Avoid parking on an incline with a trailer. If this must be done, follow these instructions.
Parking on an Incline
1. Set the parking brake and the brakes.
2. Have someone block the wheels of the vehicle and trailer while you apply the brakes.
3. After the wheels are blocked, release the parking brake and the brakes slowly, allowing
the blocks to bear the load.
4. Set the parking brake fi rmly.
5. If the vehicle has an automatic transaxle, put the selector lever in P. If it has a manual
transaxle, place the gear shift in 1 or R.
Starting on an Incline
1. Start the engine (page 4-5 ).
2. Release the parking brake and slowly pull away a short distance from the wheel blocks.
3. Stop on the nearest level ground, set the parking brake, and pick up the wheel blocks.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 197 of 671
4–57
When Driving
Transaxle
Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever:
Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle move
forward with the selector lever in the
reverse position. Otherwise, the engine
may stop, causing the loss of the power
brake and power steering functions,
and make it diffi cult to control the
vehicle which could result in an
accident.
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
NOTE
(Some models)
The accelerator pedal may initially feel
heavy as it is being depressed, then feel
lighter as it is depressed further. This
change in pedal force aids the engine
control system in determining how
much the accelerator pedal has been
depressed for performing kickdown,
and functions to control whether or not
kickdown should be performed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight and
grade steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 216 of 671
4–76
When Driving
Brake
Brake System
Foot Brake
This vehicle has power-assisted brakes
that adjust automatically through normal
use.
Should power-assist fail, you can stop by
applying greater force than normal to the
brake pedal. But the distance required to
stop will be greater than usual.
WARNING
Do not coast with the engine stalled or
turned off, fi nd a safe place to stop:
Coasting with the engine stalled or
turned off is dangerous. Braking will
require more effort, and the brake's
power-assist could be depleted if you
pump the brake. This will cause longer
stopping distances or even an accident.
Shift to a lower gear when going down
steep hills:
Driving with your foot continuously on
the brake pedal or steadily applying the
brakes for long distances is dangerous.
This causes overheated brakes,
resulting in longer stopping distances
or even total brake failure. This could
cause loss of vehicle control and a
serious accident. Avoid continuous
application of the brakes.
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
CAUTION
Do not drive with your foot held
on the clutch pedal or brake pedal,
or hold the clutch pedal depressed
halfway unnecessarily. Doing so
could result in the following:
The clutch and brake parts will
wear out more quickly.
The brakes can overheat
and adversely affect brake
performance.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 329 of 671
5–7
Interior Features
Air-Conditioning System
Recirculated air position ()
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
Heating
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
NOTE
If the windscreen fogs up easily, set
the mode selector dial to the
position. If cooler air is desired at face level,
set the mode selector dial to the
position and adjust the temperature
control dial to maintain maximum
comfort.
The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffi c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
fl ashing (page 4-36 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air
conditioning off (page 7-29 ).
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 547 of 671
*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
Parking in an Emergency .................................................................. 7-2
Parking in an Emergency .............................................................. 7-2
Flat Tyre .............................................................................................. 7-3
Spare Tyre and Tool Storage ......................................................... 7-3
Emergency Flat Tyre Repair Kit
* ................................................ 7-10
Changing a Flat Tyre (With Spare Tyre) ..................................... 7-17
Battery Runs Out ............................................................................. 7-24
Jump-Starting .............................................................................. 7-24
Emergency Starting ......................................................................... 7-27
Starting a Flooded Engine (SKYACTIV-G 2.0 ) ........................ 7-27
Push-Starting ............................................................................... 7-27
Running Out of Fuel (SKYACTIV-D 1.5) .................................. 7-28
Overheating ...................................................................................... 7-29
Overheating ................................................................................. 7-29
Emergency Towing ........................................................................... 7-31
Towing Description ..................................................................... 7-31
Towing/Tiedown Hooks .............................................................. 7-32
Warning/Indicator Lights and Warning Sounds ........................... 7-35
If a Warning Light Turns On or Flashes...................................... 7-35
Message Indicated on Display
* ................................................... 7-48
Warning Sound is Activated ........................................................ 7-50
When Liftgate Cannot be Opened .................................................. 7-55
When Liftgate Cannot be Opened ............................................... 7-55
Active Driving Display Does Not Operate ..................................... 7-56
If the Active Driving Display does not operate .......................... 7-56
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 575 of 671
7–29
If Trouble Arises
Overheating
Overheating
If the High engine coolant temperature
warning light illuminates, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Switch the ignition to off and make
sure the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefi nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the High engine coolant temperature
warning light illuminates:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the bonnet and start the engine.
If neither coolant nor steam is
escaping:
Open the bonnet and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 576 of 671
7–30
If Trouble Arises
Overheating
If you fi nd a leak or other damage, or if
coolant is still leaking:
Stop the engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
SKYACTIV-G 2.0
Cooling system cap Coolant reservoir
Cooling fan
SKYACTIV-D 1.5
Cooling system cap Coolant reservoir
Cooling fan
If you fi nd no problems, the engine is
cool, and no leaks are obvious:
Carefully add coolant as required (page
6-29 ).
CAUTION
If the engine continues to overheat or
frequently overheats, have the cooling
system inspected. The engine could
be seriously damaged unless repairs
are made. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 583 of 671
7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-28 . If it's low, add the appropriate amount of engine oil
while being careful not to overfi ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Light
The light fl ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can fi nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-29 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 652 of 671
10–6
Index
Keys ...................................................... 3-2
Key suspend function ...................... 3-7
Transmitter ...................................... 3-4
L
Label Information ................................. 9-2
Lane-Change Signals .......................... 4-68
Lane Departure Warning System
(LDWS) ............................................. 4-105
LDWS switch .............................. 4-108
Lane departure warning system (LDWS)
warning sound ..................................... 7-53
Laser Sensor ...................................... 4-154
Leaving Home Light System .............. 4-63
Liftgate ................................................ 3-19
Luggage compartment ................... 3-22
When Liftgate Cannot be Opened ... 7-55
Light Bulbs
Replacement .................................. 6-46
Specifi cations .................................. 9-8
Lighting Control.................................. 4-58
Lights-on reminder .............................. 7-50
Lubricant Quality .................................. 9-6
Luggage Compartment Light ............ 5-146
M
Maintenance
Information ...................................... 6-2
Scheduled ........................................ 6-3
Maintenance Monitor .......................... 6-15
Manual Transaxle Operation ............... 4-44
Map Lights ........................................ 5-146
Mazda Radar Cruise Control
(MRCC) ............................................ 4-124
Close proximity warning ............. 4-127
Display indication ....................... 4-127
Setting the system ....................... 4-128
Shift-up/shift-down request
display ......................................... 4-132
Mazda Radar Cruise Control (MRCC)
System warnings ................................. 7-53 Message Indicated on Display ............ 7-48
Meters and Gauges .............................. 4-23
Mirror Defogger .................................. 4-74
Mirrors
Outside mirrors.............................. 3-31
Rearview mirror ............................ 3-33
O
Odometer and Trip Meter ........... 4-26, 4-24
Outside Mirrors ................................... 3-31
Outside Temperature Display .............. 4-30
Outside temperature warning beep ..... 7-53
Over Rev. buzzer ................................. 7-54
Overhead Console ............................. 5-151
Overhead Lights ................................ 5-146
Overheating ......................................... 7-29
Owner Maintenance
Closing the Bonnet ........................ 6-20
Engine Compartment Overview .... 6-21
Key battery replacement ............... 6-39
Opening the Bonnet....................... 6-19
Owner Maintenance Precautions... 6-17
P
Parking Brake ...................................... 4-77
Parking Sensor System ..................... 4-177
Park assist sensor system
operation ...................................... 4-179
Sensor detection range ................ 4-179
Personalisation Features ...................... 9-13
Power Steering .................................... 4-97
Power Windows .................................. 3-34
Power steering warning buzzer ........... 7-54
R
Radar Sensor (Front) ......................... 4-151
Radar Sensors (Rear) ........................ 4-156
Rear Coat Hooks ............................... 5-154
Rear Cross Traffi c Alert (RCTA) ...... 4-121
Rear Door Child Safety Locks ............ 3-19
$ 9 @ & ; & & % @ & E J U J P O J O E C