engine MAZDA MODEL CX-3 2017 Owner's Manual - RHD (UK, Australia) (in English)

2–4
Essential Safety Equipment
Seats
CAUTION
  When operating a seat, be careful not to put your hands or ¿ ngers near the moving
parts of the seat or on the side trim to prevent injury.
  When moving the seats, make sure there is no cargo in the surrounding area. If the
cargo gets caught it could damage the cargo.
  (Manual Seat)  When moving the seats forward and rearward or returning a rear-reclined seatback
to its upright position, make sure you hold onto the seatback with your hand while
operating. If the seatback is not held, the seat will move suddenly and could cause
injury.
NOTE
  When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
 
 (Power Seat)  The seat-bottom power adjustment is operated by motors. Avoid extended operation
because excessive use can damage the motors.
 


 To prevent the battery from running down, avoid using the power adjustment when
the engine is stopped. The adjuster uses a large amount of electrical power.
 


 Do not use the switch to make more than one adjustment at a time.

 
 When getting in and out of the vehicle, your foot could accidentally contact the seat
height adjustment lever and cause the seat to lower.
 Adjust the seat to obtain the correct driving position.

2–7
Essential Safety Equipment
Seats
*Some models.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
 


 Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
  Refer to Seat Operation on page 2-5 .



 Active driving display (display position,
brightness level, display information)
  Refer to Active Driving Display on page
4-33 .

CAUTION
Do not place ¿ ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
¿ ngers or hands could get pinched and
injured.

SET button

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
  Lumbar support adjustment cannot
be programmed.
  Individual seat positions can be
programmed to the two available
programming buttons on the side
of the driver's seat, plus one seat
position for each registered key.
  If the vehicle has been serviced and
the battery leads disconnected, the
programmed seat positions will have
been erased. Re-programme the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 

 
 Programming using a button on
the side of the seat

 Press the button you want to
programme, either button 1 or 2, until
a beep sound is heard one time.
 

 
 Programming using the key 
 Press the key button until a beep
sound is heard one time.

NOTE
If a beep sound is heard three times, the
operation is cancelled.

2–8
Essential Safety Equipment
Seats
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving
position adjustment is completed.

NOTE
  If the driving position movement is
not changed, only the beep sounds.
  A seat position can be called up even
with the engine not running.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted. (Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat
position adjustment begins within
40 seconds of opening the driver's door,
and a beep sounds when the operation
is ¿ nished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.

NOTE
  If there is no driving position
movement, a beep is not heard.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted.

2–10
Essential Safety Equipment
Seats
CAUTION
Do not use organic solvents to clean the
seat. It may damage the seat surface and
the heater.
NOTE
  If the ignition is switched off while
the seat warmer is operating (High,
Mid or Low) and then switched
ON again, the seat warmer will
automatically operate at the
temperature set before switching off
the ignition.
  Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine
not running could cause the battery
power to be depleted.
  The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
Rear Seat
Split Folding the Seatbacks
By lowering the rear seatbacks the luggage
compartment space can be expanded.
WARNING
Do not drive the vehicle with occupants
on folded down seatbacks or in the
luggage compartment.
Putting occupants in the luggage
compartment is dangerous because seat
belts cannot be fastened which could
lead to serious injury or death during
sudden braking or a collision.

Do not allow children to play inside the
vehicle with the seatbacks lowered.
Allowing children to play in the vehicle
with the seatbacks folded down is
dangerous. If a child enters the luggage
compartment and the seatbacks were
raised back up, the child may become
trapped in the luggage compartment
which could lead to an accident.

Tightly secure cargo in the luggage
compartment when it is transported
with the seatbacks folded down.
Driving without tightly securing cargo
and luggage is dangerous as it could
move and become an obstruction to
driving during emergency braking or
a collision resulting in an unexpected
accident.

3–1*Some models.3–1
3Before Driving
Use of various features, including keys, doors, mirrors and windows.

Keys ...................................................... 3-2
Keys ............................................... 3-2
Keyless Entry System .................... 3-3

Advanced Keyless Entry System ....... 3-9
Advanced Keyless Entry
System
* ........................................... 3-9
Operational Range ....................... 3-10

Doors and Locks ................................ 3-11
Door Locks ................................... 3-11
Liftgate ......................................... 3-20

Fuel and Emission ............................. 3-25
Fuel and Engine Exhaust
Precautions ................................... 3-25
Fuel-Filler Flap and Cap .............. 3-30

Steering Wheel................................... 3-32
Steering Wheel ............................. 3-32

Mirrors ............................................... 3-34
Mirrors ......................................... 3-34

Windows ............................................. 3-38
Power Windows ........................... 3-38
Sunroof
* ....................................... 3-41

Security System ................................. 3-44
Modi¿ cation and Add-On
Equipment .................................... 3-44
Immobilizer System ..................... 3-44
Theft-Deterrent System
* ............... 3-46
Driving Tips ....................................... 3-50
Running-In ................................... 3-50
Saving Fuel and Protection of the
Environment ................................. 3-50
Hazardous Driving ....................... 3-51
Floor Mat ..................................... 3-51
Rocking the Vehicle ..................... 3-52
Winter Driving ............................. 3-53
Driving In Flooded Area .............. 3-56
Turbocharger Information
(SKYACTIV-D 1.5) ..................... 3-57

Towing ................................................ 3-58
Towing Caravans and Trailers
(Europe/Russia/Turkey/
South Africa) ................................ 3-58

3–3
Before Driving
Keys

A code number is stamped on the plate
attached to the key set; detach this plate
and store it in a safe place (not in the
vehicle) for use if you need to make a
replacement key (auxiliary key).
Also write down the code number and
keep it in a separate safe and convenient
place, but not in the vehicle.

If your key (auxiliary key) is lost, consult
your Authorised Mazda Repairer and have
your code number ready.
NOTE
The driver must carry the key to ensure
the system functions properly.

Auxiliary key Transmitter
Key code number plate

To use the auxiliary key, pull out the
auxiliary key from the transmitter while
pressing the knob.

Knob

Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors and
the liftgate.
The system can start the engine without
having to take the key out of your purse or
pocket.
Operating the theft-deterrent system is
also possible on theft-deterrent system-
equipped vehicles.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
 


 KEY Warning Light (Red)
 Refer to Warning/Indicator Lights on
page 4-36 .
 


 Ignition Not Switched Off (STOP)
Warning Beep
  Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-65 .
 


 Key Removed from Vehicle Warning
Beep
  Refer to Key Removed from Vehicle
Warning Beep on page 7-66 .

If you have a problem with the key,
consult an expert repairer, we recommend
an Authorised Mazda Repairer.

If your key is lost or stolen, consult an
Authorised Mazda Repairer as soon as
possible for a replacement and to make the
lost or stolen key inoperative.

3–6
Before Driving
Keys
Lock button
To lock the doors and the liftgate, press the
lock button and the hazard warning lights
will À ash once.
(With the advanced keyless function
(Except European models))
A beep sound will be heard once.


NOTE
  (European models)  The doors and the liftgate cannot be
locked by pressing the lock button
while any other door is open. The
hazard warning lights will also not
À ash.
 (Except European models)  The doors and the liftgate cannot be
locked by pressing the lock button
while any other door or the liftgate is
open. The hazard warning lights will
also not À ash.

 (With the i-stop function
(European models))
 Removing the key from the vehicle,
closing all the doors and pressing the
LOCK button on the key while the
i-stop function is operating (engine
is stopped) will switch the ignition
OFF and lock all the doors (Steering
wheel also locks).
 Refer to i-stop on page 4-13 .   Make sure all doors and the liftgate
are locked after pressing the button.
  (With double locking system)  Pressing the lock button twice within
3 seconds will activate the double
locking system.
 Refer to Double Locking System on
page 3-13 .
  (With theft-deterrent system)  When the doors are locked by
pressing the lock button on the key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.

3–7
Before Driving
Keys
*Some models.
Unlock button
To unlock the doors and the liftgate, press
the unlock button and the hazard warning
lights will À ash twice.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.


NOTE
  (Auto re-lock function)  After unlocking with the key,
all doors and the liftgate will
automatically lock if any of the
following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights
will À ash for con¿ rmation.
 The time required for the doors to
lock automatically can be changed.
 Refer to Personalisation Features on
page 9-13 .
 


 A door or the liftgate is opened.



 The ignition is switched to any
position other than off.


 (With theft-deterrent system)  When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is
turned off, the hazard warning lights
will À ash twice to indicate that the
system is turned off.
Intrusion sensor cancel button *
To cancel the intrusion sensor (part of
the theft-deterrent system), press the
intrusion sensor cancel button within 20
seconds after pressing the lock button and
the hazard warning lights will À ash three
times.
Refer to Theft-Deterrent System on page
3-46 .


Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Starting the Engine
NOTE
  Starting the engine may be possible
even if the key is outside of the
vehicle and extremely close to a door
and window, however, always start
the engine from the driver's seat.
 If the vehicle is started and the key
is not in the vehicle, the vehicle will
not restart after it is shut off and the
ignition is switched to off.
  The luggage compartment is out
of the assured operational range,
however, if the key (transmitter) is
operable the engine will start.

3–8
Before Driving
Keys
With the advanced keyless function


Interior aerial
Operational range

Without the advanced keyless function


Interior aerial
Operational range

NOTE
The engine may not start if the key is
placed in the following areas:
 
 Around the instrument panel 
 In the storage compartments such as
the glove compartment or the centre
console
Key Suspend Function
If a key is left in the vehicle, the
functions of the key left in the vehicle are
temporarily suspended to prevent theft of
the vehicle.
To restore the functions, press the unlock
button on the functions-suspended key in
the vehicle.

3–9
Before Driving
Advanced Keyless Entry System
*Some models.
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
The advanced keyless function allows you
to lock/unlock the door and the liftgate, or
open the liftgate while carrying the key.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
 






 Request switch Inoperable Warning
Beep
  Refer to Request Switch Inoperable
Warning Beep (With the advanced
keyless function) on page 7-66 .
 


 Key Left-in-luggage Compartment
Warning Beep
  Refer to Key Left-in-luggage
Compartment Warning Beep (With the
advanced keyless function) on page
7-66 .
 


 Key Left-in-vehicle Warning Beep
 Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-66 .

NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated,
you will be unable to start the engine
by carrying the key. Consult an expert
repairer, we recommend an Authorised
Mazda Repairer for details. If the
advanced keyless entry system has been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .