light MAZDA MODEL CX-3 2017 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2017Pages: 582, PDF Size: 7.09 MB
Page 197 of 582
4–77
When Driving
i-ACTIVSENSE
When the System Operates
1. The system goes on operation standby
when the LDWS switch is pressed
and the LDWS OFF indicator light
in the instrument cluster turns off.
For vehicles equipped with the active
driving display, the driving lane (border
lines) is indicated in the display.
Indication on display
2. Drive the vehicle in the center of the
driving lane while the LDWS OFF
indicator light is turned off. The system
becomes operational when all of the
following conditions are met.
y
The vehicle is driven in the center
of the driving lane with the white
or yellow lines on the left and right
sides, or on either side.
y
The vehicle speed is 70 km/h (44
mph) or faster.
y
The vehicle is driven on a straight
road or road with gentle curves.
For vehicles equipped with the active
driving display, the driving lane is
indicated in the display.
Indication on display
The LDWS does not operate in the
following cases:
y
The system cannot detect white or
yellow lines.
y
The vehicle speed is less than 65
km/h (40 mph).
y
The vehicle is making a sharp turn.
y
The vehicle is making a curve at an
inadequate speed.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 198 of 582
4–78
When Driving
i-ACTIVSENSE
N O T E
y The LDWS does not operate until the
system detects a white or yellow line on
either the left or right.
y When the system detects a white or
yellow line on one side only, the system
will activate the warning only when the
vehicle deviates on the side where the
white or yellow line is being detected.
y The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
Refer to Personalization Features on
page 9-10 .
Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
y The temperature inside the camera is
high or low.
y The windshield around the camera is
foggy.
y The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.
For vehicles equipped with the active
driving display, the lane (border lines) is
indicated in the display. The LDWS is
enabled automatically when the operation
conditions are met, and the LDWS
warning light turns off.
Auto cancel warning
When the following operations are
performed, the LDWS determines that
the driver intends to make a lane change
and the LDWS warning is canceled
automatically. The LDWS is enabled
automatically after the driver performs the
operation.
y The steering wheel is operated abruptly.
y The brake pedal is depressed abruptly.
y The accelerator pedal is depressed
abruptly.
y The turn signal lever is operated (after
the turn signal lever is returned, the
LDWS may not operate for about 3
seconds which is the period of time
required to make a lane correction).
N O T E
After about 60 seconds have elapsed with
the turn signal lever left operating, the
LDWS warning may operate if the vehicle
is close to a white or yellow line.
Canceling the System
Press the LDWS switch to cancel the
LDWS. The LDWS OFF indicator light
turns on.
For vehicles with the active driving
display, the driving lane indication in the
active driving display is not indicated
when the LDWS is cancelled.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 199 of 582
4–79
When Driving
i-ACTIVSENSE
LDWS Warning
If the system determines that there is the
possibility of a lane departure, the LDWS
warning beep activates and the LDWS
warning light À ashes. Operate the steering
wheel appropriately and steer the vehicle
to the center of the lane.
For vehicles equipped with the active
driving display, if there is the possibility of
a lane departure, the system indicates the
direction it determines that the vehicle is
deviating in the active driving display.
Indication on display
N O T E
y If the LDWS warning sound is set to
rumble *1 , the sound will be heard from
the vehicle speaker on the side which
the system determined the vehicle may
be deviating from its lane.
y It may be dif ¿ cult to hear the LDWS
warning beep depending on the
surrounding conditions such as outside
noise.
y The volume of the LDWS warning sound
can be changed.
Refer to Personalization Features on
page 9-10 .
y The type of warning sound (rumble *1 /
beep) on the LDWS can be changed.
Refer to Personalization Features on
page 9-10 .
*1 A rumble strip is a series of grooves in
the road pavement surface positioned at
speci ¿ c intervals, and when the vehicle
passes over it a vibration and rumble
sound is produced which alerts the
driver that the vehicle is departing from
the lane.
The rumble sound is a reproduction of
the sound which occurs when a vehicle
passes over a rumble strip.
Rumble
Groove
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 200 of 582
4–80
When Driving
i-ACTIVSENSE
*Some models.
Blind Spot Monitoring (BSM) *
The Blind Spot Monitoring (BSM) is designed to assist the driver in checking the area to the
rear of the vehicle on both sides during lane changes by alerting the driver to the presence of
vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) detects vehicles approaching from the rear while
traveling in the forward direction at a speed of 10 km/h (6.3 mph) or faster and turns on the
Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending on
the conditions. If the turn signal lever is operated to signal a lane change in the direction
in which the Blind Spot Monitoring (BSM) warning light is illuminated, the system warns
the driver of a vehicle in the detection area by À ashing the Blind Spot Monitoring (BSM)
warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind the vehicle.
Detection areas Your vehicle
WARNING
Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 201 of 582
4–81
When Driving
i-ACTIVSENSE
N O T E
y The Blind Spot Monitoring (BSM) will operate when all of the following conditions are
met:
y The ignition is switched ON.
y The Blind Spot Monitoring (BSM) switch is pressed and the Blind Spot Monitoring
(BSM) OFF indicator light in the instrument cluster is turned off.
y The vehicle speed is about 10 km/h (6.3 mph) or faster.
y The Blind Spot Monitoring (BSM) will not operate under the following circumstances.
y The vehicle speed falls below about 5 km/h (3 mph) even though the Blind Spot
Monitoring (BSM) OFF indicator light is turned off.
y The selector lever is shifted to reverse (R) and the vehicle is reversing.
y In the following cases, the Blind Spot Monitoring (BSM) OFF indicator light turns on and
operation of the system is stopped. If the Blind Spot Monitoring (BSM) OFF indicator
light remains illuminated, have the vehicle inspected at an Authorized Mazda Dealer as
soon as possible.
y Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights is detected.
y A large deviation in the installation position of a radar sensor (rear) on the vehicle has
occurred.
y There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear). Remove any snow, ice or mud on the rear bumper.
y Driving on snow-covered roads for long periods.
y The temperature near the radar sensors (rear) becomes extremely hot due to driving
for long periods on slopes during the summer.
y The battery voltage has decreased.
y Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be dif ¿ cult to detect them.
y A vehicle is in the detection area at the rear in an adjacent driving lane but it does not
approach. The Blind Spot Monitoring (BSM) determines the condition based on radar
detection data.
y A vehicle is traveling alongside your vehicle at nearly the same speed for an extended
period of time.
y Vehicles approaching in the opposite direction.
y A vehicle in an adjacent driving lane is attempting to pass your vehicle.
y A vehicle is in an adjacent lane on a road with extremely wide driving lanes. The
detection area of the radar sensors (rear) is set at the road width of expressways.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 202 of 582
4–82
When Driving
i-ACTIVSENSE
y In the following cases, the activation of the Blind Spot Monitoring (BSM) warning lights
and the warning beep may not occur or they may be delayed.
y A vehicle makes a lane change from a driving lane two lanes over to an adjacent lane.
y Driving on steep slopes.
y Crossing the summit of a hill or mountain pass.
y The turning radius is small (making a sharp turn, turning at intersections).
y When there is a difference in the height between your driving lane and the adjacent lane.
y Directly after pressing the Blind Spot Monitoring (BSM) switch and the system
becomes operable.
y If the road width is extremely narrow, vehicles two lanes over may be detected.
The detection area of the radar sensors (rear) is set according to the road width of
expressways.
y The Blind Spot Monitoring (BSM) warning lights may turn on in reaction to stationary
objects on the road or the roadside such as guardrails, tunnels, sidewalls, and parked
vehicles.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.
The walls at the entrance and exits of tunnels,
turnouts.
y A Blind Spot Monitoring (BSM) warning light may À ash or the warning beep may be
activated several times when making a turn at a city intersection.
y Turn off the Blind Spot Monitoring (BSM) while pulling a trailer or while an accessory
such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing the system to not operate normally.
y In the following cases, it may be dif ¿ cult to view the illumination/ À ashing of the Blind
Spot Monitoring (BSM) warning lights equipped on the door mirrors.
y Snow or ice is adhering to the door mirrors.
y The front door glass is fogged or covered in snow, frost or dirt.
y The system switches to the Rear Cross Traf ¿ c Alert function when the selector lever is
shifted to the reverse (R) position.
Refer to Rear Cross Traf ¿ c Alert (RCTA) on page 4-89 .
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 203 of 582
4–83
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) Warning Lights/Blind Spot Monitoring (BSM)
Warning Beep
The Blind Spot Monitoring (BSM) or Rear Cross Traf ¿ c Alert (RCTA) system noti ¿ es the
driver of the presence of vehicles in adjacent lanes to the rear of your vehicle using the
Blind Spot Monitoring (BSM) warning lights and the warning beep while the systems are
operational.
Blind Spot Monitoring (BSM) warning lights
The Blind Spot Monitoring (BSM) warning lights are equipped on the left and right door
mirrors. The warning lights turn on when a vehicle approaching from the rear in an adjacent
lane is detected.
When the ignition is switched ON, the malfunction warning light turns on momentarily and
then turns off after a few seconds.
Forward driving (Blind Spot Monitoring (BSM) operation)
The Blind Spot Monitoring (BSM) detects vehicles approaching from the rear and turns on
the Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors according
to the conditions. Additionally, while a Blind Spot Monitoring (BSM) warning light is
illuminated, if the turn signal lever is operated to signal a turn in the direction in which
the Blind Spot Monitoring (BSM) warning light is illuminated, the Blind Spot Monitoring
(BSM) warning light À ashes.
Reverse driving (Rear Cross Traf ¿ c Alert (RCTA) operation)
The Rear Cross Traf ¿ c Alert (RCTA) detects vehicles approaching from the left and right of
your vehicle and À ashes the Blind Spot Monitoring (BSM) warning lights.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 204 of 582
4–84
When Driving
i-ACTIVSENSE
Function for cancelling illumination dimmer
When the headlight switch is in the
or position, the brightness of the Blind Spot
Monitoring (BSM) warning lights is dimmed.
If the Blind Spot Monitoring (BSM) warning lights are dif ¿ cult to see due to glare from
surrounding brightness when traveling on snow-covered roads or under foggy conditions,
press the dimmer cancellation button to cancel the dimmer and increase the brightness of
Blind Spot Monitoring (BSM) warning lights when they turn on.
Refer to Dashboard Illumination on page 4-19 .
Blind Spot Monitoring (BSM) warning beep
The Blind Spot Monitoring (BSM) warning beep is activated simultaneously with the
À ashing of a Blind Spot Monitoring (BSM) warning light.
Blind Spot Monitoring (BSM) OFF
Indicator Light
y When the ignition is switched ON, the
malfunction warning light turns on
momentarily and then turns off after a
few seconds.
y The Blind Spot Monitoring (BSM) OFF
indicator light illuminates when the
Blind Spot Monitoring (BSM) switch
is pressed to turn off the Blind Spot
Monitoring (BSM) and Rear Cross
Traf ¿ c Alert (RCTA) systems.
y A malfunction in the system may
be indicated under the following
conditions. Have your vehicle inspected
at an Authorized Mazda Dealer.
y
The light does not turn on when the
ignition is switched ON.
y
The light remains turned on even if the
Blind Spot Monitoring (BSM) switch
is operated.
y
It turns on while driving the vehicle.
Blind Spot Monitoring (BSM)
Switch
When the Blind Spot Monitoring
(BSM) switch is pressed, the Blind Spot
Monitoring (BSM) and Rear Cross Traf ¿ c
Alert (RCTA) systems are turned off and
the Blind Spot Monitoring (BSM) OFF
indicator light in the instrument cluster
turns on.
If the switch is pressed again, the Blind
Spot Monitoring (BSM) and Rear Cross
Traf ¿ c Alert (RCTA) systems become
operable and the Blind Spot Monitoring
(BSM) OFF indicator light turns off.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 207 of 582
4–87
When Driving
i-ACTIVSENSE
Indication on Display
The Distance Recognition Support System (DRSS) operation status is displayed in the
active driving display.
Problems are indicated in the center display (Type B audio). If there is a problem, take
appropriate action according to the displayed message.
Refer to Warning/Indicator Lights on page 4-24 .
NOTE
y When the ignition is switched off, the operation status before the system was turned off
is maintained. For example, if the ignition is switched off with the Distance Recognition
Support System (DRSS) operable, the system will be operable when the ignition is
switched ON the next time.
y The Distance Recognition Support System (DRSS) can be turned on/off and the system's
sensitivity can be changed.
Refer to Personalization Features on page 9-10 .
Vehicle ahead
display
Distance between
vehicle display
Distance-between-vehicles guidelines *1
Indication on display Distance between vehicles
guidelines
(During travel at about 40km/h
(25 mph)) Distance between vehicles
guidelines
(During travel at about 80km/h
(50 mph))
About 25 m (82 ft) About 50 m (164 ft)
About 20 m (66 ft) About 40 m (131 ft)
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D
Page 209 of 582
4–89
When Driving
i-ACTIVSENSE
*Some models.
Rear Cross Traf ¿ c Alert (RCTA) *
T h e R e a r C r o s s T r a f ¿ c Alert (RCTA) system is designed to assist the driver in checking the
area to the rear of the vehicle on both sides while the vehicle is reversing by alerting the
driver to the presence of vehicles approaching the rear of the vehicle.
The Rear Cross Traf ¿ c Alert (RCTA) system detects vehicles approaching from the left and
right sides of the vehicle while the vehicle is being reversed out of a parking space, and
noti ¿ es the driver of possible danger using the Blind Spot Monitoring (BSM) warning lights
and the warning buzzer.
Detection areas
Your vehicle
Rear Cross Traf ¿ c Alert (RCTA) operation
1. The Rear Cross Traf ¿ c Alert (RCTA) system operates when the selector lever is shifted
to the reverse (R) position.
2. If there is the possibility of a collision with an approaching vehicle, the Blind
Spot Monitoring (BSM) warning light À ashes and the warning beep is activated
simultaneously.
% : A ( * ' # ' A ' F K V K Q P K P F D % : A ( * ' # ' A ' F K V K Q P K P F D