clock MAZDA MODEL CX-3 2017 (in English) User Guide

5–83
Interior Features
Bluetooth®
4. Rotate the audio control dial and select
the name of the paired device you
would like to delete.



Device name 1
Device name 2
Device name 3
Device name 4
Device name 5
Device name 6
Device name 7

N O T E
Only the names of paired devices can be
displayed. If only one device is paired,
only the name for this device is displayed.

5. If a selection other than “ GO BACK ”
is made and the audio control dial is
pressed, “ SURE ? NO ” is displayed.
6. Rotate the audio control dial clockwise
and switch the display to “ SURE ?
YES ”.
N O T E
The display changes as follows depending
on whether the audio control dial is
rotated clockwise or counterclockwise.
-Clockwise: “ SURE ? YES ” displayed
-Counterclockwise: “ SURE ? NO ”
displayed

7. Press the audio control dial to delete
the selected device.
N O T E
Select “ GO BACK ” and press the audio
control dial to return to the “ PAIR
DELETE ” display.

8. “ PAIR DELETED ” is displayed for
three seconds after the deletion is
completed, and then it returns to the
normal display.
N O T E
If an error occurs while trying to delete
the paired device, “ Err ” À ashes in the
display for three seconds and the display
returns to “ LINK DELETE ”.

Bluetooth ® audio device information
display
1. Using the audio control dial, select the
pair device information display mode
“DEVICE INFO” in the “BT SETUP”
mode. (Refer to “Bluetooth
® audio
device set-up” for details.)
2. Press the audio control dial to
determine the mode.
3. The name of the Bluetooth
® unit device
is displayed.
4. Rotate the audio control dial to select
the information for the Bluetooth
® unit
which you would like to view.


Device name
BT address

N O T E
When “ GO BACK ” is selected and the
audio control dial is pressed, the display
returns to “ DEVICE INFO ”.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–49
Maintenance and Care
Owner Maintenance
Daytime running lights/Parking lights/
Front side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front side-marker lights/Parking lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.



4. Install the new bulb in the reverse order
of the removal procedure.

Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.



3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–50
Maintenance and Care
Owner Maintenance
*Some models.
Fog lights * , Side turn signal lights * ,
Brake lights/Taillights (With LED
headlights), Rear side-marker lights
(With LED headlights),Taillights (With
LED headlights), High-mount brake
light
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Rear turn signal lights, Brake lights/
Taillights (With halogen headlights),
Rear side-marker lights (With halogen
headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the bolts counterclockwise and
remove them.


3. Pull the unit rearward to remove it.



4. Turn the socket and bulb assembly
counterclockwise and remove it.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–51
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.
Rear turn signal lights



Brake lights/Taillights



Rear side-marker lights



6. Install the new bulb in the reverse order
of the removal procedure.

Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–52
Maintenance and Care
Owner Maintenance
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the socket and bulb assembly
counterclockwise and remove it.



4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of the removal procedure.

Replacing Interior Light Bulbs
Overhead lights (Front)/Map lights,
Overhead lights (Rear)
1. Wrap a small À athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the À athead screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead lights (Front)/Map lights






%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–5
If Trouble Arises
Flat Tire
Jack
To remove the jack
1 . (With luggage board)
Lift up the luggage board.
2. (With luggage board)
Pull the luggage board outward a
little and insert the opposite end into
the holders so that the luggage board
stands.


Luggage board
Holders

3. Lift the luggage mat.


Luggage mat
4. Remove the cargo sub compartment.



5. Remove the cover.


Tabs

6. Turn the wing bolt and jack screw
counterclockwise.


Wing bolt
Jack screw

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–6
If Trouble Arises
Flat Tire
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing down and turn
the wing bolt clockwise to temporarily
tighten it.
2. Turn the jack screw in the direction
shown in the ¿ gure.


Wing bolt
Jack screw

3. Turn the wing bolt completely to secure
the jack.
N O T E
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suf¿ ciently tightened.

4. Insert the cover tabs and install the
cover.
N O T E
Verify that the cover is securely installed.
M a i n t e n a n c e
 




y Always keep the jack clean.



y Make sure the moving parts are kept
free from dirt or rust.
 


y Make sure the screw thread is
adequately lubricated.

Spare Tire
Your Mazda has a temporary spare tire.
The temporary spare tire is lighter and
smaller than a conventional tire, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tires should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare tire
on the front wheels (driving wheels):
Driving with the temporary spare tire
on one of the front driving wheels is
dangerous. Handling will be aff ected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tire to the front wheel and install the
temporary spare tire to the rear.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–8
If Trouble Arises
Flat Tire
4. For vehicles equipped with a sub-
woofer, uncouple the connector.


Connector
N O T E
Extra strength may be required to
uncouple the connector. Be sure to squeeze
the tab ¿ rmly.

5. For vehicles equipped with a sub-
woofer, loosen the hold-down bolt and
remove the woofer and spare tire.



For vehicles not equipped with a sub-
woofer, turn the spare tire hold-down
bolt counterclockwise and remove the
spare tire.


Spare tire hold-down bolt

To secure the spare tire
Store the spare tire in the reverse order
of removal. After storing, verify that the
spare tire is stored securely.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–10
If Trouble Arises
Flat Tire
Removing a Flat Tire
1. If your vehicle is equipped with a
wheel cover, pry off the wheel cover
with the beveled end of the jack lever.



N O T E
Force the end of the jack lever ¿ rmly
between wheel and cover, or removal will
be dif¿ cult.

CAUTION
Align the notch on the wheel cover
with the valve stem when installing it.


Tire valve Notch

Damage could occur during
installation if the wheel cover is not
properly aligned.

2. Loosen the lug nuts by turning them
counterclockwise one turn each, but do
not remove any lug nuts until the tire
has been raised off the ground.



3. Place the jack on the ground.
4. Turn the jack screw in the direction
shown in the ¿ gure and adjust the jack
head so that it is close to the jack-up
position.


Jack head

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–12
If Trouble Arises
Flat Tire
7. Insert the jack lever and attach the lug
wrench to tire jack.



8. Turn the jack handle clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is ¿ rmly in position and that it
cannot slip or move.



WARNING
Do not jack up the vehicle higher than is
necessary:
Jacking up the vehicle higher than
is necessary is dangerous as it could
destabilize the vehicle resulting in an
accident.

Do not start the engine or shake the
vehicle while it is jacked up:
Starting the engine or shaking
the vehicle while it is jacked up is
dangerous as it could cause the vehicle
to fall off the jack resulting in an
accident.

Never go under the vehicle while it is
jacked up:
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if the
vehicle were to fall off the jack.

9. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel and center cap.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD