height adjustment MAZDA MODEL CX-3 2017 Owners Manual (in English)

2–4
Essential Safety Equipment
Seats
CAUTION
 


¾ When operating a seat, be careful not to put your hands or fi ngers near the moving parts of
the seat or on the side trim to prevent injury.
 


¾ When moving the seats, make sure there is no cargo in the surrounding area. If the cargo
gets caught it could damage the cargo.
 


¾ When moving the seats forward and rearward or returning a rear-reclined seatback to its
upright position, make sure you hold onto the seatback with your hand while operating. If
the seatback is not held, the seat will move suddenly and could cause injury.

N O T E
 


y When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
 


y When getting in and out of the vehicle, your foot could accidentally contact the seat
height adjustment lever and cause the seat to lower.
  Adjust the seat to obtain the correct driving position.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

2–5
Essential Safety Equipment
Seats
Front Seat
Seat Operation


Seat Slide
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.

Height Adjustment (Driver's Seat)
To adjust the seat height, move the lever up or down.

Seat Recline
To change the seatback angle, lean forward slightly while raising the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to its original position and the seatback is locked in place by
attempting to push it forward and backward.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

2–10
Essential Safety Equipment
Seats
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the
rear center seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted.
In addition, always raise the head
restraints on all rear seat when they are
being used:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be seriously
injured in a collision.

Height Adjustment
Adjust the head restraint so that the center
is even with the top of the passenger's ears.



To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.
Front outboard seat



%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–23
When Driving
Instrument Cluster and Display
N O T E
 


y It may be dif¿ cult to view the display when wearing sunglasses. Take off your sunglasses
or adjust the luminosity.
 


y If the battery has been removed and re-installed or the battery voltage is low, the adjusted
position may deviate.
 


y The display may be dif¿ cult to view or temporarily affected by weather conditions such as
rain, snow, light, and temperature.
 


y If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information: 



y Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings
 Refer to Mazda Radar Cruise Control (MRCC) on page 4-92 .



y Lane Departure Warning System (LDWS) Operation Conditions and Warnings
 Refer to Lane Departure Warning System (LDWS) on page 4-74 .



y Smart City Brake Support (SCBS) Operation Conditions
 Refer to Smart City Brake Support (SCBS) on page 4-103 .



y Smart Brake Support (SBS) Operation Conditions and Warnings
 Refer to Smart Brake Support (SBS) on page 4-108 .



y Distance Recognition Support System (DRSS) Operation Conditions and Warnings
 Refer to Distance Recognition Support System (DRSS) on page 4-86 .



y Vehicle Speed Setting Using Cruise Control
 Refer to Cruise Control on page 4-122 .



y Turn-by-Turn (TBT) (Direction and Distance) and Lane Guidance



y Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the center
display (Type B audio).

1. Select the icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
 

y
 Height : Active driving display position


y
 Brightness Control : Method for adjusting screen brightness (Automatically/
Manually)
 

y
 Calibration : Brightness initialization setting (when selecting automatic adjustment)


y
 Brightness : Brightness adjustment (when selecting manual adjustment)


y
 Navigation : On/Off


y
 Active Driving Display : On/Off


y
 Reset
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD