service MAZDA MODEL CX-30 2019 (in English) Owner's Guide

Towing Description
▼Towing Description
We recommend that towing be done
only by an expert repairer (we
recommend an Authorised Mazda
Repairer) or a commercial tow-truck
service.

Proper lifting and towing are necessary
to prevent damage to the vehicle.
Particularly when towing a AWD
vehicle, where all the wheels are
connected to the drive train, proper
transporting of the vehicle is absolutely
essential to avoid damaging the drive
system. Government and local laws
must be followed.
1. Wheel dollies

A towed FWD vehicle should have its
drive wheels (front wheels)
off the
ground. If excessive damage or other
conditions prevent this, use wheel
dollies.

When towing a FWD vehicle with the
rear wheels on the ground, release the
parking brake.
Refer to Electric Parking Brake (EPB) on
page 4-70.

A towed AWD vehicle must have all its
wheels
off the ground.
WARNING
Always tow a AWD vehicle with all
four wheels
off the ground:
Towing a AWD vehicle with either the
front or rear wheels on the ground is
dangerous as the drive train could be
damaged, or the vehicle could trail
away from the tow truck and cause an
accident. If the drive train has been
damaged, transport the vehicle on a
flatbed truck.
CAUTION
¾Do not tow the vehicle pointed
backward with driving wheels on the
ground. This may cause internal
damage to the transmission.
¾Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or flatbed
equipment.
If Trouble Arises
Emergency Towing
7-46

¾If the parking brake cannot be
released when towing the vehicle,
transport the vehicle with all front
and rear wheels raised off the ground
as shown in the figure. If the vehicle
is towed without raising the wheels
off the ground, the brake system
could be damaged.
1. Wheel dollies
If towing service is not available in an
emergency, the vehicle may be towed
with all four wheels on the ground
using the towing hook at the front of
the vehicle.
Only tow the vehicle on paved surfaces
for short distances at low speeds.
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
1. Shift to neutral (Manual
transmission), or the N position
(Automatic transmission).
2. Switch the ignition to ON.
3. Release the parking brake.
Refer to Electric Parking Brake (EPB)
on page 4-70.
Remember that power assist for the
brakes and steering will not be
available when the engine is not
running.
Towing Hooks
▼Towing Hooks
CAUTION
¾The towing eyelet should be used in
an emergency (to get the vehicle out
of a ditch or a snow bank, for
example).
¾When using the towing eyelets,
always pull the lead or chain in a
straight direction with respect to the
eyelet. Never apply a sideways force.
NOTE
When towing with chain or lead, wrap
the chain or lead with a soft cloth near
the bumper to prevent damage to the
bumper.
1. Remove the towing eyelet, wheel
brace, and the jack lever or
equivalent from the luggage
compartment (page 7-24).
2. Wrap a flathead screwdriver or jack
lever or a similar tool with a soft
cloth to prevent damage to a
painted bumper, and open the cap
located on the front or rear
bumper.
Front
If Trouble Arises
Emergency Towing
7-47

Display*1*2Content Action to be taken
Depress Brake Pedal to
Start EngineThis message is indicated when the
push button start is pressed without
depressing the brake pedal.When starting the engine, press the
push button start with the brake ped-
al depressed.
Depress Clutch Pedal to
Start EngineThis message is indicated when the
push button start is pressed without
depressing the clutch pedal.When starting the engine, press the
push button start with the clutch
pedal depressed.
Press Push Button Start
Switch While Turning
Steering Wheel Left or
RightThis message is indicated while the
steering wheel is locked.Release the steering wheel lock by
pressing the start button while turn-
ing the steering wheel to the left and
right.
Check Gear Selector
Lever PositionThis message is indicated when the
selector lever is shifted to the P or R
position while driving.Check the selector lever position.
Close Door and Fasten
Seat BeltThis message is indicated when AU-
TOHOLD is about to operate and a
door is opened or a seat belt is unfas-
tened.When the AUTOHOLD is turned on,
close the doors and fasten seat belts.
Wiper Blades Must Be
on Windscreen Before
OperatingThis message is indicated when the
ignition is switched ON with the wip-
er arms at the service positions.Return the wiper arms to the initial
positions.
Windscreen Wiper
Range of Motion Re-
duced. Remove Ob-
struction(s)This message is indicated when there
is snow or dirt accumulation on the
windscreen and the wiper operation
range is narrowed.Remove foreign matter from the
windscreen.
Ignition Not Switched
OffThis message is indicated when the
driver’s door is opened without
switching the ignition OFF.Switch the ignition OFF before leaving
the vehicle.
Gear Selector Lever Not
in ParkDisplays when the push button start
is pressed while the selector lever is
in a position other than P, and the ig-
nition is switched to ACC.Shift the selector lever to the P posi-
tion and then switch the ignition OFF.
Excessive Transmission
Temperature. Drive
SlowlyThis message is indicated when the
internal temperature of the automatic
transmission is high.Drive slowly to reduce load on the
automatic transmission.
Excessive Transmission
Temperature. Stop Vehi-
cle in a safe LocationThis message is indicated when the
automatic transmission
fluid temper-
ature is abnormally high.Park the vehicle in a safe place imme-
diately and contact an expert repairer
(we recommend an Authorised Maz-
da Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-65

Collection and
Processing of Data in the
Ve h i c l e
▼Collection and Processing of Data
in the Vehicle
In-vehicle data processing
Electronic control units are installed in
your vehicle. These control units
process data they, for example, receive
from vehicle sensors, generate
themselves or exchange with each
other. Some control units are required
for the safe operation of your vehicle,
others provide you with support while
driving (driver assistance systems) or
enable comfort or infotainment
functions.

General information on in-vehicle data
processing is provided below. Further
information regarding which specific
data is collected and stored in your
vehicle and transmitted to third
parties, and for what purpose, can be
found under the heading ‘data
protection’ in the respective operating
instructions where direct links are
made to the affected functional
specifications. These operating
instructions are also available online
and, depending on the vehicle
configurations, in digital format on the
vehicle.

Personal references
Every vehicle is
identified by means of
a unique vehicle identification number.
This vehicle
identification number is
traceable to the current and former
owners of the vehicle. Data collected
from the vehicle also can be traced
back to the owner or driver of the
vehicle by other means, e.g., the
number plate.

The data generated or processed by
the control units therefore may be
personal data or may, under certain
circumstances, be personally
identifiable data. Depending on what
vehicle data is available, it may be
possible to draw conclusions with
regard to, for example, your driving
behaviour, your location or your route,
or consumption patterns.

Your rights with regard to data
protection
Under current data protection law, you
have certain rights with regard to
companies which process your
personal data.

Accordingly, you are entitled to request
the comprehensive disclosure of
information, free of charge, vis-a-vis
the manufacturer and third parties
(e.g., commissioned breakdown
services or workshops, providers of
online services on the vehicle),
provided that these have stored
personal data relating to you. You may
request information regarding what
data is stored about you, for what
purpose and the origination of that
data. Your right to information also
extends to the transfer of data to other
third parties.

For more information on your legal
rights relating to Mazda (for example,
your right to the deletion and
correction of data), please refer to the
applicable Data Protection Policy on
the country-specific Mazda website,
Customer Information
Collection and Processing of Data in the Vehicle
8-5

where contact details are also
provided.

Data, which is exclusively stored locally
on the vehicle, may be viewed with
expert assistance, e.g., in a vehicle
workshop, in return for payment if
appropriate.

Legal requirements regarding the
disclosure of data
To the extent that legal regulations
exist, manufacturers are obliged to
release information stored by them, at
the request of public authorities, to the
extent required on a case-by-case
basis (e.g., when a criminal offence is
being investigated).

Public authorities are also permitted to
read the data from vehicles in specific
cases, within the scope of applicable
law. For example, in the event of an
accident, information can be read from
the air bag control unit to help clarify
the circumstances of the accident.

Operational data on the vehicle
Control units process data in order to
operate the vehicle.

These include, for example:
xvehicle status information (e.g.,
speed, deceleration, lateral
acceleration, wheel speed, seatbelt
usage indicator),
xenvironmental conditions (e.g.,
temperature, rain sensor, distance
sensor).

These data are generally volatile and
are not stored beyond the operating
time, and only processed on the
vehicle itself. Control units frequently
contain data storage media. These can
be used to document, either
temporarily or permanently,
information about the condition of the
vehicle, component stress,
maintenance requirements and
technical events and failures.

The following information may be
stored, depending on the technical
configuration:
xoperating conditions of system
components (e.g.,
fill levels, tyre
pressures and battery status),
xmalfunctions and defects in
important system components (e.g.,
lighting and brakes),
xresponse of the system to
extraordinary driving situations (e.g.,
deployment of an air bag, activation
of stability control systems),
xinformation on events in which the
vehicle is damaged,
xfor electric vehicles, the state of
charge of the high-voltage battery
and the vehicle’s estimated range.

In particular cases (e.g., if the vehicle
has detected a malfunction), it may be
necessary to store data which would
normally be volatile.

If you make use of services (e.g., repair
and maintenance services), it may be
possible, if necessary, to read out and
use the stored operating data together
with the vehicle identification number.
The data from the vehicle may be read
out by employees of the Mazda
Network (e.g. authorised workshops,
manufacturer) or by third parties (e.g.,
breakdown services, independent
repair shops). The same applies in the
case of warranty cases and quality
assurance measures.

The data is usually read out via the
mandatory OBD (on-board
Customer Information
Collection and Processing of Data in the Vehicle
8-6

diagnostics) connection on the vehicle.
The operating data read out document
the technical conditions of the vehicle
or individual components and help
with fault diagnostics, compliance with
warranty obligations and quality
improvement. These data, in particular
information regarding component
stress, technical events, operating
errors and other errors are transmitted
to the manufacturer, if necessary,
together with the vehicle identification
number. In addition, product liability
falls under the responsibility of the
manufacturer. For this purpose, the
manufacturer uses operating data
external to the vehicles, for example,
recall campaigns. These data also may
be used to verify the customer’s
statutory warranty and manufacturer
warranty claims.

Error memory on the vehicle can be
reset by a service operator within the
course of repair and maintenance work
or at your request.

Comfort and infotainment functions
You can store comfort settings and
customisations on the vehicle, and
change/reset these at any time.

Depending on the particular vehicle
configurations, these may include:
xseat and steering wheel position
settings,
xchassis adjustments and
air-conditioning settings,
xcustomisations such as interior
lighting.

You are also able to incorporate data
into the vehicle’s infotainment
functions yourself within the context of
the selected configuration.

Depending on the particular vehicle
configurations, these may include:
xmultimedia data, e.g., music,
films
or photos for playback in an
integrated multimedia system,
xaddress book data for use in
conjunction with an integrated
hands-free system or integrated
navigation system,
xnavigation destinations entered,xdata relating to the use of internet
services.

This data for comfort and infotainment
functions may be stored locally on the
vehicle or it may be located on a
device that you have connected to your
vehicle (e.g., smartphone, USB stick or
MP3 player). Provided that you have
entered this data yourself, you will be
able to delete it at any time.

Transmission of this data from the
vehicle is exclusively at your request, in
particular, relating to the settings you
have selected when using online
services.

Smartphone integration, for example,
Android Auto or Apple car play

If your vehicle is equipped accordingly,
you will be able to connect your
smartphone or another mobile device
to the vehicle so that you can control it
using the integrated control elements
within the vehicle. Smartphone images
and sounds can be output via the
vehicle’s multimedia system. At the
same time, specific information is
transferred to your smartphone.
Depending on the type of integration,
Customer Information
Collection and Processing of Data in the Vehicle
8-7

this may include location data,
antidazzle mode and other general
vehicle information. Please familiarise
yourself with the operating instructions
for the vehicle/infotainment system.

Integration enables selected
smartphone apps to be used, for
example, navigation or music
playback. Further interaction between
the smartphone and the vehicle does
not take place, in particular, active
access to vehicle data. The nature of
any further data processing is
determined by the app provider.
Whether and which settings can be
used depends on the particular app
and the operating system of your
smartphone.

Online services
If your vehicle is equipped with a
wireless network connection, this
enables the exchange of data between
your vehicle and other systems. The
wireless connection is enabled by
means of a transmission and receiving
unit which is specific to the vehicle or
via a mobile terminal (e.g.,
smartphone) that you have installed.
Online functions can be used via this
network connection. These include
online services and applications (apps)
provided to you by the manufacturer
or another provider.

Services provided by the manufacturer
For our online services, the respective
functions are described by Mazda in
an appropriate place (e.g., in the
operating instructions and/or on the
country-specific Mazda website) and
provided together with the associated
data protection information. Personal
data may be used to provide online
services. The exchange of data for thispurpose takes place via a protected
connection, for example, using the IT
systems intended for this. In addition
to the provision of services, the
collection, processing and use of
personal data takes place exclusively
on the basis of a legal permission, for
example, in the case of emergency call
systems required by law, by means of a
contractual agreement or approval.

You can activate or deactivate the
(sometimes chargeable) services and
functions in the vehicle, and
sometimes even the entire wireless
connection. Functions and services
required by law, such as emergency
call systems, are excluded from this.

Third-party services
If you choose to make use of the
online services of other providers (third
parties), these services shall come
under the responsibility of the
respective provider and be subject to
their data protection conditions and
terms of use. The manufacturer
generally has no influence with regard
to the content exchanged in this way.

Please inform yourself about the
nature, scope and purpose with regard
to the collection and use of personal
data within the context of third-party
services by the respective service
provider.

(For Europe)
Further information regarding data
protection can be found on the Mazda
website.
Please visit “https://
www.mazdamotors.eu” to find your
country-specific webpage.
Customer Information
Collection and Processing of Data in the Vehicle
8-8

Information for Users on
Collection and Disposal
of Old Equipment and
Used Batteries
▼Information for Users on
Collection and Disposal of Old
Equipment and Used Batteries
When disposing your old battery,
please refer to the information as
follows.
▼Information on Disposal in the
European Union
These crossed-out wheeled bin
symbols on the products, packaging ,
and/or accompanying documents
mean that used electronic products
and batteries should not be mixed with
general household waste. For proper
treatment, recovery and recycling of
old products and used batteries,
please take them to applicable
collection points, in accordance with
your national legislation and the
Directives 2006/66/EC.

By disposing of these products and
batteries correctly, you will help to save
valuable resources and prevent any
potential negative effects on human
health and the environment which
could otherwise arise from
inappropriate waste handling.

For more information about collection
and recycling of old products and
batteries, please contact your local
municipality, your waste disposal
service or the point of sales where you
purchased the items.
NOTE
The bottom two letters might be used
in combination with the crossed-out
wheeled bin symbol. In this case it
complies with the requirement
established by the Directive for the
chemical involved.
“Pb” and “Cd” mean lead and
cadmium respectively.
▼Information on Disposal in Other
Countries Outside the European
Union
The above symbols are only valid in the
European Union. If you wish to discard
old products and used batteries,
please contact your local authorities,
your waste disposal service or the
point of sales where you purchased the
items, and ask for the correct method
of disposal.
Customer Information
Collection/Disposal of Old Equipment/Used Battery
8-68

Lubricant Classification
Brake/Clutch fluidWith M Hybrid Mazda Genuine Brake Fluid or equivalent
Without M Hybrid SAE J1703 or FMVSS116 DOT-3 or DOT-4
*1 Mazda Long Life Gear Oil G7 is superior oil for low fuel cost and optimum shift-feel. Using Mazda
Long Life Gear Oil G7 is recommended.
If Mazda Long Life Gear Oil G7 cannot be obtained, use standard oil (API Service GL-4 (SAE
75W-80)).
▼Cleaner
Cleaner Classification
Deposit Cleaner
*1Mazda genuine deposit cleaner
(K002 W0 001)
*1 Use Mazda genuine deposit cleaner. Using non-genuine deposit cleaner would cause internal failure
of the fuel system. Refer to 3-30, 6-3, 6-6 for the details.
▼Capacities
(Approximate Quantities)
Item Capacity
Engine oilSKYACTIV-G 2.0With oil filter replacement 4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil filter replacement 4.0 L (4.2 US qt, 3.5 Imp qt)
SKYACTIV-G 2.5With oil filter replacement 4.5 L (4.8 US qt, 4.0 Imp qt)
Without oil filter replacement 4.3 L (4.5 US qt, 3.8 Imp qt)
SKYACTIV-X 2.0With oil filter replacement 4.6 L (4.9 US qt, 4.0 Imp qt)
Without oil filter replacement 4.4 L (4.6 US qt, 3.9 Imp qt)
SKYACTIV-D 1.8With oil filter replacement 5.1 L (5.4 US qt, 4.5 Imp qt)
Without oil filter replacement 4.7 L (5.0 US qt, 4.1 Imp qt)
Specifications
Specifications
9-7