instrument cluster MAZDA MODEL CX-30 2019 (in English) Repair Manual

The vehicle speed preset using the
cruise control is displayed in the
instrument cluster and the active
driving display (vehicles with active
driving display).
Instrument cluster (Basic display)
Instrument cluster (i-ACTIVSENSE
display)
Active driving display
▼Changing the Set Vehicle Speed
Follow either of these procedures.
To increase/decrease speed using
cruise control switch
When the RES switch is pressed up
(SET+), the vehicle accelerates and
when the RES switch is pressed down
(SET-), it decelerates.
xPress and release immediately: 1
km/h (1 mph)
xPress and hold: 10 km/h (5 mph)
NOTE
Even after releasing the RES switch, the
cruise control accelerates/decelerates
continuously until the set speed
displayed in the instrument cluster and
on the active driving display is reached.
If you want to stop accelerating/
decelerating, change the set speed or
cancel the system (such as by
depressing the brake pedal).
To increase speed using accelerator
pedal
Depress the accelerator pedal and
press the RES switch up (SET+) or
down (SET-) at the desired speed. If
the switch is not operated, the system
returns to the set speed after you
release your foot from the accelerator
pedal.
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere
with or change the set speed. Take
your foot off the accelerator to return
to the set speed.
▼To Resume Cruising Speed at More
Than 30 km/h (19 mph)
If the cruise control system is
temporarily cancelled (such as by
applying the brake pedal) and the
system is still activated, the most
recent set speed will automatically
resume when the RES switch is
pressed.
If vehicle speed is below 30 km/h (19
mph), increase the vehicle speed up to
When Driving
Cruise Control
4-230

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Vent Operation
▼Adjusting the Vents
Directing airflow
To adjust the direction of
airflow, move
the adjustment knob.
NOTE
xWhen using the air conditioner
under humid ambient temperature
conditions, the system may blow fog
from the vents. This is not a sign of
trouble but a result of humid air
being suddenly cooled.
xThe air vents can be fully opened and
closed by operating the knob/dial.
Driver's Side Vents
Air vent open/close
1. Knob
2. Open
3. Close
NOTE
The figure indicates the air vent on the
left side of the instrument cluster. The
operation direction for the air vent on
the right side of the instrument cluster
is symmetrical with the air vent on the
left side.

Airflow direction adjustment
1. Knob

Passenger's Side Vents
Air vent open/close
1. Knob
2. Open
3. Close

Interior Features
Air-Conditioning System
5-3

xWhenever the engine oil is replaced, the vehicles engine control unit needs to be
reset as soon as possible. Otherwise the wrench indicator light or engine oil
warning light may turn on. To reset the engine control unit, consult an expert
repairer (we recommend an Authorised Mazda Repairer) or refer to the vehicle
status monitor section in the Mazda Connect Owner's Manual.
▼Inspecting Engine Oil Level
NOTE
xIf the engine oil level warning
indication/warning light turns on,
add 1 L (0.3 US gal, 0.2 Imp gal) of
engine oil.
x(SKYACTIV-D 1.8)
If “Excessive Oil Level. Have the
Vehicle Inspected” is displayed on
the multi-information display in the
instrument cluster, have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5
minutes for the oil to return to the
sump.
4.(SKYACTIV-X 2.0)
Open the engine cover (page
6-19).
5. Pull out the dipstick, wipe it clean,
and reinsert it fully.
SKYACTIV-G 2.0 and SKYACTIV-G
2.5

1. MAX
2. OK
3. MIN

SKYACTIV-X 2.0

1. MAX
2. OK
Maintenance and Care
Owner Maintenance
6-27

No.FUSE RAT-
INGPROTECTED COMPONENT
F39ŠŠ
F40 40 A Air conditioner
F41ŠŠ
F42 20 A Windscreen wiper
F43 30 A
Cooling fan
*
F44 30 A Starter
F45 10 A Engine control system
F46 15 A Audio
F47 15 A For protection of various circuits
F48 7.5 A Air bag
F49 15 A Instrument cluster
F50 15 A Room light
F51 25 A Audio
F52 10 A
Sunroof
*
F53 15 A Engine control system
F54 15 A i-ACTIVSENSE
F55 50 A
For protection of various circuits
*
F56 50 AŠ
Maintenance and Care
Owner Maintenance
*Some models.6-51

Parking in an Emergency
▼Parking in an Emergency
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.

The hazard warning lights warn other
drivers that your vehicle is a traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the direction indicators will
flash. The hazard warning indicator
lights in the instrument cluster flash
simultaneously.
NOTE
xThe direction indicators do not work
when the hazard warning lights are
on.
xCheck local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
▼Roadside Emergency Triangle
Retaining Strap
Keep the roadside emergency triangle
in the right side trim and secure it with
the strap.
1. Strap
If Trouble Arises
Parking in an Emergency
*Some models.7-23

If a Warning Light Turns
On or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/flashes,
take appropriate action for each light.
There is no problem if the light turns
off, however if the light does not turn
off or turns
on/flashes again, consult
an expert repairer (we recommend an
Authorised Mazda Repairer).
The details for some warnings can be
viewed on the centre display or
multi-information display in the
instrument cluster.
Centre display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to
view the warning details.
NOTE
You can also display the currently
occurring warning by sliding the
commander knob to the left while on
the home screen of the centre display.
Multi-information display
1. Press the INFO switch on the
steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-23.
▼Brake System Warning Indication/
Warning Light (Red)
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the ignition is
switched on, and turns off a few
seconds later or when the engine is
started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
Refer to Inspecting Brake/Clutch Fluid
Level on page 6-30.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
expert repairer (we recommend an
Authorised Mazda Repairer) to have
the brakes inspected as soon as
possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
CAUTION
¾In addition, the
effectiveness of the
braking may diminish so you may
need to depress the brake pedal
more strongly than normal to stop
the vehicle.
¾(With M Hybrid)
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-49

perform the applicable procedure
(page 3-8).
▼Power Liftgate Warning Beep*
If system operation precautions are
necessary, the driver is notified by the
warning sound.
Warning beep What to check
The beep sounds 3
timesThe conditions re-
quired for the power
liftgate to operate have
not been met, such as
an object being stuck
in the liftgate.
The beep sound con-
tinuesThe vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
▼Low Fuel Warning Beep
When the low fuel warning light
flashes, a warning beep is activated
once at the same time.
▼Electronic Steering Lock Warning
Beep
The warning beep operates if the
steering wheel is not unlocked after the
push button start is pressed. (page
4-4)
▼Brake System Warning Beep (With
M Hybrid)
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the centre display.
xAutomatic transmission problemxIncrease in automatic transmission
internal temperature
xM Hybrid problemxBrake fluid amount decreasexEngine oil level sensor problemxElectric Parking Brake (EPB) problemxEngine hydraulic pressure decreasexEngine coolant temperature increasexEngine system problem
▼Shift Position Warning Beep
A sound is activated when the push
button start is pressed while the
selector lever is in a position other
than P, and the ignition is switched to
ACC. Check the selector lever
position.
▼Ignition Not Off Reminder
Warning Beep (With M Hybrid)
A warning beep is activated
continuously if the driver's door is
opened with the selector lever in a
position other than the P or N
position. Shift the selector lever to the
P or N position, or close the driver's
door.
▼i-stop Warning Beep*
xIf the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-69

that engine idling is stopped. It stops
when the driver's door is closed.
x(European model)
The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not
restart automatically to ensure safety.
Start the engine using the normal
method.
(With M Hybrid)
x(Manual transmission)
With the shift lever in a position
other than neutral, the driver's
door is opened.
x(Automatic transmission)
With the selector lever in the D or
M (not in second gear
fixed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
(Without M Hybrid)
x(Manual transmission)
With the shift lever in a position
other than neutral, the driver's seat
belt is unfastened and the driver's
door is opened.
x(Automatic transmission)
With the selector lever in the D or
M (not in second gear fixed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
▼Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under
the following conditions:
xThe vehicle is driven with the parking
brake applied.
xThe Electric Parking Brake (EPB)
switch is pulled while the vehicle is
driven.
xYou attempt to start driving the
vehicle while the conditions for
releasing the Electric Parking Brake
(EPB) automatically have not been
met.
▼AUTOHOLD Warning Beep
Message is displayed and beep sound
is activated simultaneously for about 5
seconds when using AUTOHOLD
function or when AUTOHOLD switch
is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.

If the message is displayed and the
beep sound is activated
simultaneously, have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Outside Temperature Warning
Beep*
Warns the driver of the possibility of icy
roads when the outside temperature is
low.
If the outside temperature is lower
than about 4 °C (39 °F) , a beep sound
is heard once and the outside
temperature display
flashes for about
10 seconds.
Refer to Outside Temperature Display
on page 4-28.
▼Vehicle Speed Alarm*
The vehicle speed alarm function is
designed to alarm the driver via a
single beep sound and a warning
indication in the instrument cluster
that the previously set vehicle speed
has been exceeded.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-70*Some models.

Warning beep type Notification content
The beep sounds in-
termittently while the
Mazda Radar Cruise
Control with Stop &
Go function (MRCC
with Stop & Go func-
tion) is operating.The distance between
your vehicle and the
vehicle ahead is too
close. Check the safety
of the surrounding
area and reduce vehi-
cle speed.
▼Excessive Speed Warning*
If the vehicle speed exceeds the speed
limit sign displayed in the active driving
display/instrument cluster, the area
around the speed limit sign flashes in
amber and the warning sound is
activated at the same time. If the
vehicle speed continues to exceed the
displayed speed limit sign, the
indication stops flashing and remains
on.
▼Speed Limiter Warning Beep*
If the vehicle speed exceeds the set
speed by about 5 km/h (3 mph) or
more, a warning beep operates
continuously. The warning beep
operates until the vehicle speed
decreases to the set speed or less.
CAUTION

If the set speed is set lower than the
current vehicle speed by pressing the
RES switch down (SET-) the warning
beep is not activated for about 30
seconds even if the vehicle speed is
faster than the newly set speed by 5
km/h (3 mph). Be careful not to drive
over the set speed.
NOTE
When the system is temporarily
cancelled by depressing the accelerator
pedal fully, the ISA/ASL display shows
the cancel display. Even if the vehicle
speed exceeds the set speed by about
5 km/h (3 mph) or more while the
cancel display is displayed, the warning
sound is not operated.
▼Collision warning*
If there is a possibility of a collision
with a vehicle ahead or an obstruction
at the rear of the vehicle, a warning
sound is activated intermittently at the
same time as the warning indications
are displayed in the instrument cluster
or active driving display.
▼Door-ajar Warning Beep
A warning beep is actived if the vehicle
is driven with any door or liftgate ajar.
Drive the vehicle after closing the
doors and liftgate.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-72*Some models.