power steering MAZDA MODEL CX-30 2019 Owners Manual (in English)

NOTE
xWhen returning a rear seat to its
original position, place the seat belt
in its normal position. Verify that the
seat belt pulls out and retracts.
x(Power Seat)
The seat-bottom power adjustment
is operated by motors. Avoid
extended operation because
excessive use can damage the
motors.
xTo prevent the battery from
running down, avoid using the
power adjustment when the
engine is stopped. The adjuster
uses a large amount of electrical
power.
xDo not use the switch to make
more than one adjustment at a
time.
Front Seat
▼Adjusting the Driver's Seat
Using the driving position set up
procedure recommended by Mazda
allows you to maintain a relaxed
posture, drive the vehicle for longer
periods without feeling tired, and
make quick operations naturally.
Also, you can be assured of a clear
view in the forward direction to help
you drive more safely and comfortably.
The adjustments for the driving
position recommended by Mazda are
done using the following procedures.
1. Moving the steering wheel and seat
to their default positions.
2. Adjusting the seatback angle.
3. Adjusting the seat position forward
and back.
4. Adjusting the seat height.
5. Adjusting the height on the front
edge of the seat bottom.
6. Adjusting the steering wheel
position.
7. Adjusting the head restraint
position.
Essential Safety Equipment
Seats
2-4

1. With your back resting against the
seatback, raise the seat to the
height where you can see the rear
edge area of the bonnet surface
from the windscreen.
1. Manual Seat
2. Power Seat

Adjusting the height on the front edge
of the seat bottom
Adjust the height on the front edge of
the seat bottom to the position where
the back of your knees contacts the
front edge of the seat bottom.
1. With your right foot set on the
accelerator pedal, adjust the height
on the front edge of the seat
bottom so that the back of your
knees lightly contacts the front edge
of the seat bottom.
2. Depress the accelerator pedal and
make sure that you no longer feel
cramping in the back of your knees.
1. Manual Seat
2. Power Seat

Adjusting the steering wheel position
Adjust the steering wheel to the
position where it can be operated
easily and the gauges can be viewed
easily.
1. With your back resting against the
seatback, extend both arms, place
them on the top of the steering
wheel, and pull the steering wheel
towards you to the position of your
wrists.
Essential Safety Equipment
Seats
2-9

2. Adjust the steering wheel height so
that the gauges can be viewed
easily.
3. Raise the lever to securely lock the
steering wheel.
Adjusting the head restraint position
To prevent shock to the head and
neck, adjust the head restraints to their
correct positions.
Refer to Height Adjustment on page
2-15.
▼Driving Position Memory (Power
Seat)*
The desired driving position can be
called up after programming the
position.
The following driving positions can be
programmed.
xDriver’s seat position (seat slide,
height adjustment, front edge of seat
bottom, seat recline)
Refer to Adjusting the Driver's Seat
on page 2-4.
xActive driving display (display
position, brightness level, display
information)
Refer to Active Driving Display on
page 4-39.
xOutside mirror angle
Refer to Outside Mirrors on page
3-36.
A driving position can be programmed
to the following parts.
xPosition memory button
xTransmitter used for vehicle
NOTE
xLumbar support adjustment cannot
be programmed.
Programming
1. Make sure the parking brake is on.
2.(Automatic transmission)
Make sure the selector lever is in
the P position.
3. Switch the ignition ON.
4. Adjust the following parts to the
desired conditions.
xDriver's seatxActive driving displayxOutside mirrors
5. Press the SET button continuously
until a sound is activated.
1. 1 button
2. 2 button
3. SET button
6. Do the following operation within 5
seconds after the sound is activated
to programme the driving position.
xProgramming to a position
memory button
Press the button you want to
programme, either 1 or 2 button.
xProgramming to the transmitter
Press the unlock button on the
transmitter.
A sound is activated when the
operation is completed correctly.
Essential Safety Equipment
Seats
2-10*Some models.

WARNING
Never stop the engine when going
down a hill:
Stopping the engine when going down
a hill is dangerous. This causes the loss
of power steering and power brake
control, and may cause damage to the
drivetrain. Any loss of steering or
braking control could cause an
accident.
Hazardous Driving
▼Hazardous Driving
WARNING
Be extremely careful if it is necessary
to downshift on slippery surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tyre
speed could cause the tyres to skid.
This could lead to loss of vehicle
control and an accident.
When driving on ice or in water, snow,
mud, sand, or similar hazards:
xBe cautious and allow extra distance
for braking.
xAvoid sudden braking and sudden
manoeuvring.
xDo not pump the brakes. Continue
to press down on the brake pedal.
Refer to Antilock Brake System (ABS)
on page 4-80.
xIf you get stuck, select a lower gear
and accelerate slowly. Do not spin
the front wheels.
xFor more traction in starting on
slippery surfaces such as ice or
packed snow, use sand, rock salt,
chains, carpeting, or other nonslip
material under the front wheels.
NOTE
Use snow chains only on the front
wheels.
Before Driving
Driving Tips
3-54

Drive Selection....................... 4-90
Drive Selection
*................... 4-90
i-ACTIV AWD......................... 4-92
i-ACTIV AWD Operation...... 4-92
Power Steering....................... 4-93
Power Steering.....................4-93
i-ACTIVSENSE......................... 4-94
i-ACTIVSENSE...................... 4-94
Adaptive Front Lighting System
(AFS)
*................................. 4-98
High Beam Control System
(HBC)
*................................ 4-99
Adaptive LED Headlights
(ALH)
*............................... 4-101
Lane Departure Warning System
(LDWS)
*............................ 4-103
Blind Spot Monitoring (BSM)
*......
........................................ 4-106
Traffic Sign Recognition System
(TSR)
*................................4-111
Distance & Speed Alert (DSA)
*.....
........................................ 4-118
Driver Attention Alert (DAA)
*.......
........................................ 4-119
Driver Monitoring (DM)
*.... 4-121
Front Cross Traffic Alert
(FCTA)
*............................. 4-123
Rear Cross Traffic Alert (RCTA)
*....
........................................ 4-126
Mazda Radar Cruise Control
(MRCC)
*........................... 4-130
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)
*......... 4-139
Cruising &
Tra ffi c Support
(CTS)
*............................... 4-148
Lane-keep Assist System (LAS)
*.....
........................................ 4-162
Adjustable Speed Limiter
(ASL)
*................................4-166
Intelligent Speed Assistance
(ISA)
*................................ 4-170
4-2*Some models.

Ignition Switch
▼Push Button Start Positions
The system operates only when the key
is within operational range.
Each time the push button start is
pressed, the ignition switches in the
order of
off, ACC, and ON. Pressing
the push button start again from ON
switches the ignition
off.
1. Indicator light
2. Push button start
NOTE
xThe engine starts by pressing the
push button start while depressing
the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission). To switch
the ignition position, press the push
button start without depressing the
pedal.
xDo not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission,
the selector lever is in the P position,
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
Off
The power supply to electrical devices
turns off and the indicator light
(amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat,
always switch the ignition off, set the
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
accident.
In addition, if your intention is to leave
the vehicle for even a short period, it is
important to switch the ignition
off, as
leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is
flashing , a message is
displayed on the multi-information,
and the beep sound is heard, this
indicates that the steering wheel is not
unlocked. To unlock the steering
wheel, press the push button start
while moving the steering wheel left
and right.
When Driving
Start/Stop Engine
4-4

position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is stopped by
depressing the brake pedal.
xThe vehicle is not driven on a
slope.
xThe vehicle is not stopped
suddenly.
NOTE
Under the following conditions, a
period of time is required to stop
engine idling
xThe battery power is depleted for
some reasons such as the vehicle has
not been driven for a long period.
xThe ambient temperature is high or
low.
xAfter the battery terminals are
disconnected for some reasons such
as for battery replacement.
x(SKYACTIV-D 1.8)
After PM removal is performed by
the diesel particulate filter.
Engine does not restart
If the following operations are
performed while the idling is stopped,
the engine will not restart for safety
reasons. In such cases, start the engine
using the normal method.
x(European model)
xThe bonnet is opened.xThe driver's seat belt is unfastened
and the driver's door is opened.
x(With M Hybrid)
xAutomatic transmission
The driver's seat belt is unfastened
and the driver's door is opened.
xManual transmission
The driver's door is opened.
Engine-stop period is short or time
until next engine idle stop is long
xThe ambient temperature is high or
low.
xThe battery power is depleted.xPower consumption by the vehicle's
electrical parts is high.
Engine restarts automatically while
engine idling is stopped
Under the following conditions, the
engine restarts automatically.
xThe i-stop OFF switch is pressed until
the beep sounds.
xThe air conditioner is operated with
the airflow mode in the
position.xThe temperature setting dial of the
air conditioner is in the maximum
heating or maximum cooling (A/C
ON) position.
x(Automatic air-conditioning)
The cabin temperature is largely
different from the set temperature of
the air conditioner.
xThe brakes are released slightly on a
slope and the vehicle begins to
move.
xTwo minutes have elapsed since the
idling was stopped.
xThe battery power is depleted.x(Automatic transmission)
Engine idling is stopped while the
vehicle is stopped
xThe accelerator pedal is depressed
with the selector lever in the D or
M (not in second gear fixed mode)
position.
xThe selector lever is shifted to the R
position.
xThe selector lever is shifted from N
or P position to D or M (not in
second gear fixed mode) position.
When Driving
Start/Stop Engine
4-15

▼Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Warning Refer to
(Red)Brake System Warning Indication/Warning Light
*17-49
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn-
ing
7-50
ABS warning
7-52
Charging System Warning Indication/Warning Light*17-50
Engine Oil Warning Indication/Warning Light*17-50
High Engine Coolant Temperature Warning Indication 7-51
Power Steering Malfunction Indication/Indicator Light*17-51
Master Warning Indication 7-52
(Amber)Brake Control System Warning Indication/Warning Light
*17-52
Brake Override Warning Indication 7-53
Check Engine Indication/Light*17-53
Petrol Particulate Filter Warning Indication/Warning Light*1(SKYAC-
TIV-X 2.0)7-54
Diesel Particulate Filter Warning Indication/Warning Light
*1(SKYAC-
TIV-D 1.8)7-54
When Driving
Instrument Cluster and Display
4-32

Driving Tips
▼Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever:
Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle
move forward with the selector lever in
the reverse position. Otherwise, the
engine may stop, causing the loss of
the power brake and power steering
functions, and make it difficult to
control the vehicle which could result
in an accident.
Passing
For extra power when passing another
vehicle or climbing steep grades,
depress the accelerator fully. The
transmission will shift to a lower gear,
depending on vehicle speed.
NOTE
xThe accelerator pedal may initially
feel heavy as it is being depressed,
then feel lighter as it is depressed
further. This change in pedal force
aids the engine control system in
determining how much the
accelerator pedal has been
depressed for performing kickdown,
and functions to control whether or
not kickdown should be performed.
xWhile the selector lever is in the M
position and the TCS is turned off,
manual shift mode does not switch
to automatic shift mode even if the
accelerator pedal is completely
depressed. Operate the selector
lever.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while
gradually accelerating.
Descending steep grades
When descending a steep grade, shift
to lower gears, depending on load
weight and grade steepness. Descend
slowly, using the brakes only
occasionally to prevent them from
overheating.
When Driving
Automatic Transmission
4-53

Power Steering
▼Power Steering
xPower steering is only operable when
the engine is running. If the engine is
off or if the power steering system is
inoperable, you can still steer, but it
requires more physical
effort.
If the steering feels stiffer than usual
during normal driving or the steering
vibrates, consult an expert repairer
(we recommend an Authorised
Mazda Repairer).
xThe malfunction indication notifies
the driver of system abnormalities
and operation conditions.
Refer to Power Steering Malfunction
Indication/Indicator Light on page
7-51.
When Driving
Power Steering
4-93