transmission oil MAZDA MODEL CX-30 2019 Owners Manual (in English)

Rocking the Vehicle
▼Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating , transmission failure, and
tyre damage.
If you must rock the vehicle to free it
from snow, sand or mud, depress the
accelerator slightly and slowly move
the shift lever/selector lever from 1 (D)
to R position.
Winter Driving
▼Winter Driving
Carry emergency gear, including tyre
chains, window scraper,
flares, a small
shovel, jumper leads, and a small bag
of sand or salt.
Ask an expert repairer (we recommend
an Authorised Mazda Repairer) to
check the following:
xHave the proper ratio of antifreeze in
the radiator.
Refer to Engine Coolant on page
6-28.
xInspect the battery and its leads.
Cold reduces battery capacity.
xUse an engine oil appropriate for the
lowest ambient temperatures that
the vehicle will be driven in (page
6-24).
xInspect the ignition system for
damage and loose connections.
xUse washer fluid made with
antifreezeŠbut do not use engine
coolant antifreeze for washer fluid
(page 6-31).
NOTE
xRemove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
xDo not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
xNever use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
Before Driving
Driving Tips
3-56

Cylinder Deactivation*
▼Cylinder Deactivation
The cylinder deactivation is a function
designed to reduce fuel consumption
and improve fuel economy by
deactivating 2 out of the 4 cylinders
while driving. The function constantly
determines which is better for driving;
4 cylinders or 2 cylinders, regardless of
the driver's operations, and it performs
the switching automatically.
When the cylinder deactivation
function does not operate
The cylinder deactivation function
does not operate under the following
conditions.
xThe selector lever is in the P, N, or R
position (automatic transmission), or
1st gear (manual transmission).
xThe engine oil temperature or engine
coolant temperature is low.
xAfter disconnecting the battery
terminals for some reason, such as
for battery replacement.
When Driving
Start/Stop Engine
4-20*Some models.

Signal Warning Refer to
(Amber)
*i-stop Warning Indication/Warning Light*17-53
*Automatic Transmission Warning Indication/Warning Light*17-55
*AWD Warning Indication/Warning Light*17-56
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning
Light*17-55
*Tyre Pressure Monitoring System (TPMS) Warning Indication/Warn-
ing Light*1
Flashing
7-57
Tu r n s o n
7-60
(Red)KEY Warning Indication/Warning Light
*17-56
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-58
*Adaptive LED Headlights (ALH) Warning Indication/Warning Light*17-58
i-ACTIVSENSE Warning Indication/Warning Light*17-58
Exterior Light Warning Indication/Warning Light*17-58
Low Fuel Warning Indication/Warning Light 7-58
Engine Oil Level Warning Indication/Warning Light*17-59
*120 km/h Warning Light*17-57
Seat Belt Warning Indication/Warning Light (Front seat) 7-59
(Red)Seat Belt Warning Light (Rear seat) 7-59
When Driving
Instrument Cluster and Display
*Some models.4-33

▼Indicators
1. Manual shift mode indication
2. Gear position indication
Manual shift mode indication
In manual shift mode, the “M” of the
shift position indication in the
instrument panel illuminates.
Gear position indication
The numeral for the selected gear
illuminates.

NOTE
xIf the gears cannot be shifted down
when driving at higher speeds, the
gear position indication will
flash
twice to signal that the gears cannot
be shifted down (to protect the
transmission).
xIf the automatic transmission fluid
(ATF) temperature becomes too
high, there is the possibility that the
transmission will switch to automatic
shift mode, cancelling manual shift
mode and turning off the gear
position indication illumination. This
is a normal function to protect the
AT. After the ATF temperature has
decreased, the gear position
indication illumination turns back on
and driving in manual shift mode is
restored.
x(SKYACTIV-D 1.8 (European
model))
If the engine oil temperature
becomes too high, there is the
possibility that the transmission will
switch to automatic shift mode,
cancelling manual shift mode and
turning off the gear position
indicator illumination. After the
engine oil temperature has
decreased, the gear position
indicator illumination turns back on
and driving in manual shift mode is
restored.
▼Gear Shift Indicator (GSI)*
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
When Driving
Automatic Transmission
*Some models.4-47

¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.

Do not get out of the vehicle while
the stop hold control is operating.
(Automatic transmission vehicle)
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before getting out of the vehicle,
switch the CTS off, apply the parking
brake, and then shift the selector lever
to the P position.

CAUTION
Turn the system off when the vehicle is
running on a chassis roller.
Heed the following cautions so that
the CTS can operate normally.
¾Turn the system off when the vehicle
is running on a chassis roller.
¾Do not modify the vehicle's
suspensions.
¾Always use wheels of the specified
size for the front and rear wheels.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for tyre replacement.

NOTE
xThe headway control does not detect
the following as physical objects.
xVehicles approaching in the
opposite direction
xPedestriansxStationary objects (stopped
vehicles, obstructions)
xIf a vehicle ahead is travelling at an
extremely low speed, the system may
not detect it correctly.
xIf there is a structure on the road or
an object (such as a monorail) at a
low height off the ground in front of
the vehicle, the system may operate.
Therefore, do not use the CTS.
xDo not use the CTS under conditions
in which close proximity warnings
are frequently activated.
xIf it is necessary to accelerate for a
lane change or the vehicle ahead
brakes suddenly causing you to close
in on the vehicle rapidly, accelerate
using the accelerator pedal or
decelerate using the brake pedal
depending on the conditions.
xWhile the CTS is in use, any intended
engine braking does not occur even
if you shift the shift lever (manual
transmission) or the selector lever
(automatic transmission). If
deceleration is required, lower the
vehicle speed setting or depress the
brake pedal.
xWhile braking by the CTS control is
operating , you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the CTS control is
operating, however, they may not
turn on while the vehicle is on a
down slope at the set vehicle speed
or travelling at a constant speed and
following a vehicle ahead.
xUnder the following conditions, the
CTS may not be able to detect white
(yellow) lines or vehicles ahead
correctly and the CTS may not
operate normally.
xThe forward sensing camera (FSC)
cannot recognise the area in front
of the vehicle due to soiling or fog.
When Driving
i-ACTIVSENSE
4-150

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Air filter *5CCRCCRCCRCCR
Fuel filter RRRR
Fuel lines and hosesExcept Uk-
raineIIIIII
Ukraine IIIIIIIIIIII
SKYACTIV-G 2.0, SKYACTIV-X 2.0, AND SKYACTIV-D 1.8
Drive belts
*6IIII
Engine coolant level IIIIIIIIIIII
Engine coolant
*7Replace at first 200,000 km (125,000 miles) or 10 years;
after that, every 100,000 km (62,500 miles) or 5 years.
Battery
*8*9IIIIIIIIIIII
Brake lines, hoses and connections IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake
fluid
*10RRRRRR
Disc brakes IIIIIIIIIIII
Manual transmission oil Replace every 180,000 km (112,500 miles).
Steering operation and linkagesIIIIII
Rear differential oil
*11
Transfer oil*11
Front and rear suspension, ball joints and
wheel bearing axial playIIIIII
Driveshaft dust boots IIIIII
Exhaust system and heat shields Inspect every 100,000 km (62,500 miles) or 8 years.
Bolts and nuts on chassis and body TTTTTT
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Cabin air filter (if installed) R R R R R R
Tyre inflation pressure and tyre wear
*12*13IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*14IIIIIIIIIIII
Self-test with Mazda Modu-
lar Diagnostic System
(M-MDS)
*15*16
SKYACTIV-G & SKYACTIV-XUkraine IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-4

Maintenance Item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Battery *3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIIIIIIIII
Brake and clutch fluid level IIIIIIIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Ty re
inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines and hoses IIIIII
Steering operation and linkages IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) RRRRRR
Hoses and tubes for emission I I I
Driveshaft dust boots I I I I
Air filter
*9RRR
Exhaust system and heat shields I I
Manual transmission oil Replace every 100,000 km or 5 years.
Spark plugSKYACTIV-G
2.0/
SKYACTIV-G
2.5Replace every 120,000 km.
SKYACTIV-X
2.0Replace every 64,000 km.
Fuel filter Replace every 135,000 km.
Engine coolant
*10Replace at first 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.
T: Tighten
R: Replace
Maintenance and Care
Scheduled Maintenance
6-7

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Exhaust system and heat shields IIIIIIIIIIII
Function of all lights I I I I I I I I I I I I
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Tyre inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines & hoses IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) R R R R R R
Hoses and tubes for emission I I I
Air
filter
*9RRRR
Manual transmission oil R R
Fuel filterExcept below
countriesReplace every 120,000 km.
Azerbaijan/
ArmeniaReplace every 60,000 km.
Engine coolant
*10Replace at first 195,000 km or 120 months; after that,
every 90,000 km or 60 months.
Rear differential oil
*11
Transfer oil*11
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust,
fill up, or replace if necessary.
T: Tighten
R: Replace
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
7,500 km or 6 months.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.
Maintenance and Care
Scheduled Maintenance
6-10

Maintenance item1st 2nd 3rd 4th 5th 6th 7th 8th 9th10t
h11t
h12t
h13t
h14t
h15t
h16t
h
Battery*5*6IIIIIIII
Va c u u m b ra ke
booster and hoseWith vac-
uum boos-
terIIIIIIII
Brake lines, hoses and connec-
tionsIIIIIIII
Steering operation and linkages I I I I I I I I
Front and rear suspension, ball
joints and wheel bearing axial
playIIIIIIII
Bolts and nuts on chassis and
bodyTTTTTTTT
Body condition (for rust, corro-
sion and perforation)IIIIIIII
Tyre inflation pressure and tyre
wear
*7IIIIIIIIIIIIIIII
Tyre rotation Rotate every 10,000 km (6,250 miles).
Emergency flat tyre repair kit (if
installed)
*8IIIIIIII
Cabin air filter (if installed) R R R R R R R R
Hoses and tubes for emission IIII
Driveshaft dust boots IIII
Brake fluid
*9RRRR
Exhaust system and heat shields Inspect every 80,000 km (50,000 miles).
Manual transmission oil Replace every 100,000 km or 60 months.
Engine coolant
*10Replace at first 200,000 km (125,000 miles) or 10 years; after that,
every 100,000 km (62,500 miles) or 5 years.
Rear differential oil
*11
Transfer oil*11
Maintenance and Care
Scheduled Maintenance
6-13

perform the applicable procedure
(page 3-8).
▼Power Liftgate Warning Beep*
If system operation precautions are
necessary, the driver is notified by the
warning sound.
Warning beep What to check
The beep sounds 3
timesThe conditions re-
quired for the power
liftgate to operate have
not been met, such as
an object being stuck
in the liftgate.
The beep sound con-
tinuesThe vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
▼Low Fuel Warning Beep
When the low fuel warning light
flashes, a warning beep is activated
once at the same time.
▼Electronic Steering Lock Warning
Beep
The warning beep operates if the
steering wheel is not unlocked after the
push button start is pressed. (page
4-4)
▼Brake System Warning Beep (With
M Hybrid)
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the centre display.
xAutomatic transmission problemxIncrease in automatic transmission
internal temperature
xM Hybrid problemxBrake fluid amount decreasexEngine oil level sensor problemxElectric Parking Brake (EPB) problemxEngine hydraulic pressure decreasexEngine coolant temperature increasexEngine system problem
▼Shift Position Warning Beep
A sound is activated when the push
button start is pressed while the
selector lever is in a position other
than P, and the ignition is switched to
ACC. Check the selector lever
position.
▼Ignition Not Off Reminder
Warning Beep (With M Hybrid)
A warning beep is activated
continuously if the driver's door is
opened with the selector lever in a
position other than the P or N
position. Shift the selector lever to the
P or N position, or close the driver's
door.
▼i-stop Warning Beep*
xIf the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-69