engine MAZDA MODEL CX-5 2020 Owners Manual (in English)

ï‚·When traveling on a downslope for a
long period of time.
ï‚·There is a problem with the system.
ï‚·The engine has stalled.
ï‚·Any of the doors is opened.
ï‚·The driver's seat belt is unfastened.
ï‚·The parking brake is automatically
applied during stop hold control.
ï‚·The radar sensor (front) cannot detect
target objects (during rain, fog, snow or
other inclement weather conditions, or
when the radiator grille is dirty).
ï‚·(With Selective Catalytic Reduction
(SCR) system)
The vehicle speed is limited by the
Selective Catalytic Reduction (SCR)
system.
Resuming control
If the MRCC with Stop & Go function
system is canceled, you can resume
control at the previously set speed by
pressing the RES switch and after all of
the operation conditions have been met.
NOTE
If the set speed is not indicated in the
display, the control does not resume even
if the RES switch is pressed.
Turning off the system
Press the OFF/CANCEL switch 2 times
while the MRCC with Stop & Go function
system is operating to switch off the
system.
When Driving
i-ACTIVSENSE
4-157
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

Resume driving information
If you do not resume driving within a few sec onds after the vehicle ahead starts moving, the
multi-information display vehicle-ahead indicat ion flashes to urge the driver to resume
driving.
â–¼ Cruise Control Function
While this function is operating, the
headway control operation is canceled and
only the cruise contro
l function operates.
The vehicle speed can be set more than
about 25 km/h (16 mph).
Use the cruise control function on
expressways and other highways which do
not require a lot of repeated acceleration
and deceleration.
WA R N I N G
Do not use the cruise control function in
the following locations:
Otherwise, it could lead to an accident.
 Roads with sharp curves and where
vehicle
traffic is heavy and there is
insufficient space between vehicles.
(Driving under these conditions using the
cruise control function is not possible)
 Steep down slopes (Set speed may be
exceeded because sufficient engine
braking cannot be applied)
 Slippery roads such as ice or snow-bound
roads (Tires could spin causing you to
lose vehicle control)
Always drive carefully:
The warnings and brake control will not
operate after the headway control function
is canceled and the system is switched to
only the cruise control function. Depress
the brake pedal to decelerate according to
the surrounding conditions while keeping a
safer distance from the vehicle ahead and
always driving carefully.
Switching to cruise control function
When the MODE switch is pressed until
the system switches to the cruise main
indication (white) while the MRCC with
Stop & Go function system is turned on,
the system switches to the cruise control
function.
When the system switches to the cruise
control function, the indicator and
multi-information display notify the driver
as follows:
ï‚·The MRCC with Stop & Go function set
indication (green) or the MRCC with
Stop & Go function main indication
(white) is turned off, and the cruise main
indication (white) is turned on.
ï‚·A message is displayed in the
multi-information display.
When Driving
i-ACTIVSENSE
4-159
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

Drive the vehicle in the center of the
vehicle lane while the system is on
standby. When all of the following
conditions are met, and the system
becomes operational.
ï‚·The engine is running.
ï‚·The vehicle speed is about 60 km/h (37
mph) or faster.
ï‚·The system detects white (yellow) lane
lines on both the right and left sides.
ï‚·The driver is operating the steering
wheel.
ï‚·The driving lane is neither narrow nor
wide.
When the system becomes operational, the
LAS & LDWS indication (white) is
displayed on the multi-information display
or active driving display.
Instrument Cluster (Type A)
Instrument Cluster (Type B)
If the indication on the active driving
display has been turned off using the
personalization features, the LAS &
LDWS indication (white) is displayed on
the multi-information display.

NOTE
When only a vehicle lane line (yellow) on
either the left or right is detected, the LAS
& LDWS indication on the active driving
display turns off.
Detection only on
either left or right Detects on both
left and right sides
Detection only on
either left or rightDetects on both
left and right sides
(Gray) (White)
No indication
Active Driving Display
Multi-information Display
If the indication on the active driving
display has been turned off using the
personalization features, the LAS & LDWS
indication on the multi-information
display is displayed in gray and the system
goes on standby.
The LAS & LDWS goes on stand-by
status in the following cases:
ï‚·The system cannot detect white (yellow)
lane lines.
ï‚·The vehicle speed is less than about 60
km/h (37 mph).
ï‚·The ABS/TCS is operating.
ï‚·The TCS is turned off.
(If the TCS is turned off while the
system is operational, a warning beep is
heard and the system goes on standby.)
ï‚·The vehicle is making a sharp curve.
ï‚·The brake pedal is depressed.
ï‚·The steering wheel is operated abruptly.
ï‚·The width of a lane is excessively
narrow or wide.
When Driving
i-ACTIVSENSE
4-165
CX-5_8HX6-EA-19I_Edition2_old
2019-9-19 9:26:07

and make sure that the indicator light turns
off.
Drive the vehicle in the center of the
driving lane while the LAS & LDWS OFF
indicator light in the instrument cluster is
turned off.
The system becomes operational when all
of the following conditions are met.
ï‚·The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
ï‚·The vehicle speed is about 60 km/h (37
mph) or faster.
ï‚·The vehicle is driven on a straight road
or road with gentle curves.
ï‚·The engine is running.
The LAS & LDWS goes on stand-by
status in the following cases:
ï‚·The system cannot detect white (yellow)
lane lines.
ï‚·The vehicle speed is less than about 60
km/h (37 mph).
ï‚·The vehicle is making a sharp curve.
ï‚·The vehicle is making a curve at an
inappropriate speed.
NOTE
ï‚·The LAS & LDWS remains on stand-by
until it detects white (yellow) lines on
both the left and right sides, or on either
side.
ï‚·When the system detects a white
(yellow) lane line on one side only, the
system will not activate warnings for the
lane line on the side that is not being
detected.
ï‚·The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
Refer to Setting Change
(Personalization Features) on page
9-11.
Vehicle lane line display
When the LAS & LDWS becomes
operational while on standby, the vehicle
lane lines are displayed in the
multi-information display. The system
changes to operational status display when
the system detects a white (yellow) line on
either the left or right.
(Stand-by status)
(Operational status)
Auto cancel
In the following cases, the LAS & LDWS
is automatically canceled, the LAS &
LDWS warning indication (amber) turns
on, and an alert is displayed. When the
When Driving
i-ACTIVSENSE
4-168
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

The vehicle is being towed or when towing another vehicle.
 The vehicle is on a chassis roller.
 When driving on rough roads such as in areas of dense grass or off-road.
Refer to Stopping the Advanced Smart City Brake Support (Advanced SCBS) System Operation
on page 4-174 on how to turn off the Advanced SCBS system.
NOTE
ï‚·The Advanced SCBS system will operate under the following conditions.
ï‚·The engine is running.
ï‚·The Smart City Brake Support (SCBS) warn ing indication(amber) does not illuminate.
ï‚·(Object is vehicle ahead)
The vehicle speed is between about 4 to 80 km/h (2 to 50 mph).
ï‚·(Object is a pedestrian)
The vehicle speed is between about 10 to 80 km/h (6.2 to 50 mph).
ï‚·The Advanced SCBS system is not turned off.
ï‚·Under the following conditions, the Advanced SCBS system may not operate normally:
ï‚·The Advanced SCBS system will not operate if the driver is deliberately performing
driving operations (accelerator pedal and steering wheel).
ï‚·If there is the possibility of partial contact with a vehicle ahead.
ï‚·The vehicle is driven on a slippery road surface such as wet roads or icy or snow-bound
roads.
ï‚·The braking performance is adversely affected due to cold temperatures or wet brakes.
ï‚·The vehicle is driven at the same speed as the vehicle ahead.
ï‚·The accelerator pedal is depressed.
ï‚·The brake pedal is depressed.
ï‚·The steering wheel is being operated.
ï‚·The selector lever is being operated.
ï‚·In the following cases, the Advanced SCBS may operate.
ï‚·Objects on the road at the entrance to a curve.
ï‚·Vehicles passing in the opposite lane while making a curve.
ï‚·When passing through a toll gate.
ï‚·When passing through low gates, narrow gates, car washing machines, or tunnels.
ï‚·If you suddenly come close to a vehicle ahead.
ï‚·2-wheeled vehicles, animals, or standing trees.
ï‚·(Manual transaxle)
If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed, the
engine stops.
When Driving
i-ACTIVSENSE
4-173
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

â–¼Collision Warning
If there is the possibility of a collision with
a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information display and the
active driving display.
NOTE
The operation distance and volume of the
collision warning can be changed. Refer
to Personalization Features on page
9-11.
â–¼Automatic Brake Operation Display
The automatic brake operation display is
indicated on the multi-information display
after the Advanced SCBS is operated.
NOTE
ï‚·The collision warning beep sounds
intermittently while the Advanced SCBS
brake or brake assist (Advanced SCBS
brake assist) is operating.
ï‚·If the vehicle is stopped by the Advanced
SCBS operation and the brake pedal is
not depressed, the warning beep sounds
1 time after about 2 seconds and the
Advanced SCBS brake is automatically
released.
â–¼Stopping the Advanced Smart City
Brake Support (Advanced SCBS)
System Operation
The Advanced SCBS system can be
temporarily deactivated.
Refer to Personalization Features on page
9-11.
When the Advanced SCBS system is
turned off, the Sma
rt City Brake Support
(SCBS) OFF indicator light turns on.

When the engine is restarted, the system
becomes operational.
NOTE
When the Advanced SCBS system is set to
inoperable, the Smart Brake Support
(SBS) are also set to inoperable.
When Driving
i-ACTIVSENSE
4-174
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

CAUTION
In the following cases, turn the system off to prevent a mis-operation:
The vehicle is being towed or when towing another vehicle.
 The vehicle is on a chassis roller.
 When driving on rough roads such as in areas of dense grass or off-road.
Refer to Stopping the Smart City Brake Support (SCBS) system Operation on page 4-177 on
how to turn off the SCBS system.
NOTE
ï‚·The SCBS system will operate under the following conditions.
ï‚·The engine is running.
ï‚·The Smart Brake Support/Smart City Brake Support (SBS/SCBS) system warning
indication/warning light (amber) does not illuminate.
ï‚·(Rear-end coll ision warning)
The vehicle speed is about 4 to 80 km/h (2 to 50 mph).
ï‚·(Brake control (Smart City Brake Support (SCBS) brake))
The vehicle speed is about 4 to 30 km/h (2 to 18 mph).
ï‚·The SCBS system is not turned off.
ï‚·Under the following conditions, the SCBS system may not operate normally:
ï‚·The SCBS system will not operate if the driver is deliberately performing driving
operations (accelerator pedal and steering wheel).
ï‚·If there is the possibility of pa rtial contact with a vehicle ahead.
ï‚·The vehicle is driven on a slippery road surface such as wet roads or icy or snow-bound
roads.
ï‚·The braking performance is adversely affected due to cold temperatures or wet brakes.
ï‚·The vehicle is driven at the same speed as the vehicle ahead.
ï‚·The accelerator pedal is depressed.
ï‚·The brake pedal is depressed.
ï‚·The steering wheel is being operated.
ï‚·The selector lever is being operated.
ï‚·In the following cases, the Forward Sensing Camera (FSC) determines that there is a
vehicle ahead and the SCBS may operate.
ï‚·Objects on the road at the entrance to a curve.
ï‚·Vehicles passing in the opposite lane while making a curve.
ï‚·Metal objects, bumps, or protruding objects on the road.
ï‚·When passing through a toll gate.
ï‚·When passing through low gates, narrow gates, car washing machines, or tunnels.
When Driving
i-ACTIVSENSE
4-176
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

ï‚·If you suddenly come close to a vehicle ahead.
ï‚·2-wheeled vehicles, pedestrians, animals or standing trees.
ï‚·Vehicle is driven with some of the tires having significant wear.
ï‚·(Manual transaxle)
If the vehicle is stopped by the Smart City Brake Support (SCBS) operation and the clutch
pedal is not depressed, the engine stops.
â–¼Smart City Brake Support (SCBS)
Indicator Light (Red)*
If the Smart City Br
ake Support (SCBS) is
operating, the indicator light (red) flashes.

â–¼ Collision Warning*
If there is the possibility of a collision with
a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information display and the
active driving display.
NOTE
The operation distance and volume of the
collision warning can be changed. Refer
to Personalization Features on page
9-11.
â–¼Automatic Brake Operation
Display*
The automatic brake operation display is
indicated on the multi-information display
after the SCBS is operated.
NOTE
ï‚·The collision warning beep sounds
intermittently while the SCBS brake or
brake assist (SCBS brake assist) is
operating.
ï‚·If the vehicle is stopped by the SCBS
operation and the brake pedal is not
depressed, the warning beep sounds 1
time after about 2 seconds and the SCBS
brake is automatically released.
â–¼Stopping the Smart City Brake
Support (SCBS) System Operation
The SCBS system can be temporarily
deactivated.
Refer to Personalization Features on page
9-11.
When Driving
i-ACTIVSENSE
*Some models.4-177
CX-5_8HX6-EA-19I_Edition2_old
2019-9-19 9:26:07

When the SCBS system is turned off, the
Smart City Brake Support (SCBS) OFF
indicator light turns on.

When the engine is restarted, the system
becomes operational.
NOTE
When the SCBS system is set to
inoperable, the Smart Brake Support
(SBS) are also set to inoperable.
Smart Brake Support
(SBS)
*
The SBS system alerts the driver of a
possible collision using a display and
warning sound if the radar sensor (front)
and the Forward Sensing Camera (FSC)
determine that there is the possibility of a
collision with a vehicle ahead while the
vehicle is being driven at about 15 km/h or
faster (10 mph or faster). Furthermore, if
the radar sensor (front) and the Forward
Sensing Camera (FSC) determines that a
collision is unavoidable, the automatic
brake control is performed to reduce
damage in the event of a collision.
In addition, when the driver depresses the
brake pedal, the brakes are applied firmly
and quickly to assist. (Brake Assist (SBS
brake assist))
WA R N I N G
Do not rely completely on the SBS system
and always drive carefully:
The SBS is designed to reduce damage in
the event of a collision, not avoid an
accident. The ability to detect an
obstruction is limited depending on the
obstruction, weather conditions, or traffic
conditions. Therefore, if the accelerator
pedal or brake pedal is mistakenly
operated it could result in an accident.
Always verify the safety of the surrounding
area and depress the brake pedal or
accelerator pedal while keeping a safer
distance from vehicles ahead or on-coming
vehicles.
When Driving
i-ACTIVSENSE
4-178*Some models.
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07

â–¼Collision Warning
If there is the possibility of a collision with
a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the multi-information display and the
active driving display.
â–¼Stopping The Smart Brake Support
(SBS) System Operation
The SBS system can be temporarily
deactivated.
Refer to Personalization Features on page
9-11.
When the SBS system is turned off, the
SBS OFF indicator light turns on.
When the engine is restarted, the system
becomes operational.
NOTE
If the SBS system operation is turned off,
the Smart City Brake Support (SCBS)
system operation is turned off
simultaneously.
When Driving
i-ACTIVSENSE
4-180
CX-5_8HX6-EA-19I_Edition2_old
2019-9-19 9:26:07