MAZDA MODEL CX-7 2008 Owners Manual (in English)

Black plate (331,1)
Light Bulbs
Headlights (Low beam)
Headlights (High beam)
High-mount brake light Fog lights
Front turn signal lights/Parking lights
Some models.
License plate lights Brake lights/Taillights
Overhead light/Map lights (Front) Overhead light (Rear)
Front side marker lights
Rear turn signal lights
Rear side marker lights
Reverse lights
Luggage compartment light
Maintenance and Care
Owner Maintenance
8-39
CX-7_8X59-EA-07E_Edition3 Page331
Wednesday, July 25 2007 3:19 PM
Form No.8X59-EA-07E

Black plate (332,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs: When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children: Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Replacing a headlight bulb
High-beam bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood. 3. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the High-beam bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
4. Disconnect the bulb from the electrical connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
5. Install the new bulb in the reverse orderof removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Make sure the headlight switch is off.
8-40
Maintenance and Care
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page332
Wednesday, July 25 2007 3:19 PM
Form No.8X59-EA-07E

Black plate (333,1)
2. If you are changing the right Low-beam bulb, start the engine, turn the
steering wheel all the way to the right,
and turn off engine. If you are
changing the left Low-beam bulb, turn
the steering wheel to the left.
3. Turn the screws and the center section of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Detach the electrical connector from
the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring. 7. Swing the retaining spring out and
away to free the bulb.
Sealing
cover
8. Carefully remove the bulb from the
socket by pulling it straight back.
9. Replace the bulb.
10. Install the new bulb in the reverse order of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Maintenance and Care
Owner Maintenance
8-41
CX-7_8X59-EA-07E_Edition3 Page333
Wednesday, July 25 2007 3:19 PM
Form No.8X59-EA-07E

Black plate (334,1)
Front side marker lights, Front turn
signal lights/Parking lights
1. Make sure the headlight switch is off.
2. If you are changing a bulb in the rightheadlight unit, start the engine, turn the
steering wheel all the way to the right,
and turn off engine. If you are
changing a bulb in the left headlight
unit, turn the steering wheel to the left.
3. Turn the screws and the center section of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.
Front side marker lights
Front turn signal lights/Parking lights
6. Install the new bulb in the reverse order of removal.
Fog lightsí
1. Make sure the headlight switch is off.
2. If you are changing the right fog lightbulb, start the engine, turn the steering
wheel all the way to the right, and turn
off engine. If you are changing the left
fog light bulb, turn the steering wheel
to the left.
3. Turn the screws and the center section of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
8-42
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page334
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (335,1)
4. Disconnect the electrical connectorfrom the bulb by pressing the tab on
the connector with your finger and
pulling the connector downward.
5. Turn the socket and bulb assembly counterclockwise and remove it.
Carefully remove the bulb from its
socket in the reflector by gently pulling
it straight backward out of the socket.
6. Install the new bulb in the reverse orderof removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Rear side-marker
lights
1. Remove the cover.
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Rear side-maker light
Brake light/Taillight
Rear direction indication light
Reverse light
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an Authorized
Mazda Dealer.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
CX-7_8X59-EA-07E_Edition3 Page335
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (336,1)
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
License plate lights
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Overhead light (Rear), Luggage
compartment light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver. 2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
8-44
Maintenance and Care
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page336
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (337,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system does not work,
first inspect the fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
Fuse panel cover
3. Pull the fuse straight out with the fuse puller provided on the inside of the
cover for the fuse panel and the fuse
block cover inside of the engine
compartment.
4. Inspect the fuse and replace it if it's
blown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the ROOM circuit.
Maintenance and Care
Owner Maintenance
8-45
CX-7_8X59-EA-07E_Edition3 Page337
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (338,1)
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
4. If any fuse but the MAIN fuse isblown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
8-46
Maintenance and Care
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page338
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (339,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE RATINGPROTECTED COMPONENT
1 IGN 2 40A Ignition system
2 BLOWER 40A Blower motor
3 BTN 60A For protection of various circuits
4 FAN 2 40A Cooling fan
5 IGN 1 40A Ignition system
6 FAN 1 40A Cooling fan
7 P.SEAT 40A Power seat
í
8INJ 30A Injector
9 ROOF 20A Moonroofí
10BOSE 30A Bose audio systemí
11ENGINE 30A Engine control system
12 D.LOCK 20A Power door locks
13 P.WIND 30A Power windows
14 FUEL 30A Fuel pump
15 ABS 1 40A ABS
16 ABS 2 20A ABS
17 DSC 7.5A DSC
18 FOG 20A Fog lights
í
Maintenance and Care
Owner Maintenance
8-47íSome models.
CX-7_8X59-EA-07E_Edition3 Page339
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (340,1)
DESCRIPTIONFUSE RATINGPROTECTED COMPONENT
19 DEF 30A Rear window defroster
20 TNS 15AParking lights, License plate lights,
Illuminated entry system
21 A/C 10A Air conditioner
í
22ETC 20A Accelerator position sensor
23 H/L HI 15A Headlight levelingí
24DRL 15A DRLí
25 H/L LO RH 15A Headlight low beam (RH)
26 H/L LO LH 15A Headlight low beam (LH)
27 ENG BAR 2 7.5A PCM
28 ECM 10A Engine control system
29 ENG BAR 1 15A Air flow sensor, EGR control valve
30 P.WIND 2 20A Power windows
31 STOP 10A Brake lights
32 HORN 20A Horn
33 ENG B+ 25A PCM
34 HAZARD 10A Hazard warning flashers, Turn signals
Fuse block (Driver's side)
DESCRIPTIONFUSE RATINGPROTECTED COMPONENT
1 OUTLET 1 15A Accessory Socket
8-48
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page340
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E