high beam MAZDA MODEL CX-7 2008 Owners Manual (in English)

Black plate (193,1)
SignalWarning/Indicator Lights Page
Seat Belt Warning Light/Beep 5-43
Door-Ajar Warning Light5-44
Low Washer Fluid Level Warning Light5-44
Automatic Transaxle Warning Light5-45
AWD Warning Light5-45
Tire Pressure Monitoring System Warning Light5-45
KEY Warning Light (Red)/KEY Indicator Light (Green)5-47
Security Indicator Light5-49
Headlight High-Beam Indicator Light5-49
Shift Position Indicator Light5-49
TCS/DSC Indicator Light5-50
TCS OFF Indicator Light5-50
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 5-51
Light-On Indicator Light5-51
Turn Signal/Hazard Warning Indicator Lights5-51
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-39
CX-7_8X59-EA-07E_Edition3 Page193
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (203,1)
NOTE
The advanced key can be set so that the KEY
indicator light (green) does not flash even if
the battery power is low.
Refer to Setting Change (Function
Customization)(page 3-18).
qSecurity Indicator Light
This indicator light starts flashing every 2
seconds when the ignition switch is turned
from the ON to the ACC position and the
immobilizer system is armed.
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:lThe high-beam headlights are on.lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
This indicates the selected shift position
when the ignition switch is in the ON
position.
Gear position indicator
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-49
CX-7_8X59-EA-07E_Edition3 Page203
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (208,1)
CAUTION
Do not shade the light sensor by
adhering a sticker or a label on the
windshield, or putting an object on it.
Otherwise the light sensor will not
operate correctly.
Sensor
NOTElWhen the headlight switch is in the AUTO
position and the ignition switch is turned to
the ACC or LOCK position, the headlights,
other exterior lights and dashboard
illumination will turn off.
lThe timing for turning on the headlights,
other exterior lights and dashboard
illumination can be delayed by adjusting
the sensitivity of the light sensor. Consult an
Authorized Mazda Dealer regarding sensor
adjustment.
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights
have xenon fusion bulbs that produce a
bright white beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs
yourself:Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
NOTE
If the headlights flicker, or the brightness
weakens, the bulb-life may be depleted and a
replacement is necessary. Consult an
Authorized Mazda Dealer.
q Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a continuous
beep sound will be heard when the
driver's door is opened.
NOTE
When the advanced keyless function is used
and the start knob is in the ACC position, the
“Start Knob Not in LOCK Warning Beep ”
(page 3-16) overrides the lights-on reminder.
5-54
Driving Your Mazda
íSome models.
Switches and Controls
CX-7_8X59-EA-07E_Edition3 Page208
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (209,1)
qHeadlight High-Low Beam
Push the lever forward for high beam.
Pull back to original position for low
beam.
High beam
Low beam
q Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch does
not need to be on, and the lever will return
to the normal position when released.
qHeadlight Levelingí
The number of passengers and weight of
cargo in the luggage compartment change
the angle of the headlights.
The headlight leveling switch adjusts this
angle.
Select the proper setting from the following chart.
Front seat Rear
seat Load Switch
Position
Driver Passenger
× ――― 0
×× ――0
×× × ―1
×× ×× 2
× ―― ×3
×: Yes
― :No
qDaytime Running Lights (Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The Daytime Running Lights turn off when the
parking brake is applied.
Driving Your Mazda
Switches and Controls
5-55íSome models.
CX-7_8X59-EA-07E_Edition3 Page209
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (210,1)
Turn and Lane-Change
Signals
qTurn Signal
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Right turn
Left turn OFF
Right lane
change
Left lane
change
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change ―until the
indicator flashes ―and hold it there. It
will return to the off position when
released.
NOTE
If an indicator light stays on without flashing
or if it flashes abnormally, one of the turn
signal bulbs may be burned out.
Fog Lightsí
Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn the front fog lights on, rotate the
fog light switch to the
position.
The headlight switch must be in the
position to turn on the front fog lights.
Fog light switch
To turn them off, rotate the fog light
switch to the OFF position or turn the
headlight switch to the
or OFF
position.
NOTE
lThe fog lights will turn off when the
headlights are set at high beam.
l(With auto-light control)
If the fog light switch is in the ON position
and the headlight switch is in the AUTO
position, the front fog lights will be turned
on when the headlights, the exterior lights
and dashboard illumination are
automatically turned on.
5-56
Driving Your Mazda
íSome models.
Switches and Controls
CX-7_8X59-EA-07E_Edition3 Page210
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (230,1)
qRadio Reception
AM characteristics
AM signals bend around such things as
buildings or mountains and bounce off the
ionosphere. Therefore, they can reach
longer distances than FM signals. Because
of this, two stations may sometimes be
picked up on the same frequency at the
same time.
Station 2
Station 1 Ionosphere
FM characteristics
An FM broadcast range is usually about
40
―50 km (25 ―30 miles) from the
source. Because of extra coding needed to
break the sound into two channels, stereo
FM has even less range than monaural
(non-stereo) FM.
FM Station
40—50km
(25—30 miles)
Signals from an FM transmitter are similar
to beams of light because they do not
bend around corners, but they do reflect.
Unlike AM signals, FM signals cannot
travel beyond the horizon. Therefore, FM
stations cannot be received at the great
distances possible with AM reception.
AM wave
FM wave
FM wave
100—200 km (60—120 miles) Ionosphere
Atmospheric conditions can also affect
FM reception. High humidity will cause
poor reception. However, cloudy days
may provide better reception than clear
days.
Multipath noise
Since FM signals can be reflected by
obstructions, it is possible to receive both
the direct signal and the reflected signal at
the same time. This causes a slight delay
in reception and may be heard as a broken
sound or a distortion. This problem may
also be encountered when in close
proximity to the transmitter.
Reflected wave
Direct
6-16
Interior Comfort
Audio System
CX-7_8X59-EA-07E_Edition3 Page230
Wednesday, July 25 2007 3:18 PM
Form No.8X59-EA-07E

Black plate (331,1)
Light Bulbs
Headlights (Low beam)
Headlights (High beam)
High-mount brake light Fog lights
Front turn signal lights/Parking lights
Some models.
License plate lights Brake lights/Taillights
Overhead light/Map lights (Front) Overhead light (Rear)
Front side marker lights
Rear turn signal lights
Rear side marker lights
Reverse lights
Luggage compartment light
Maintenance and Care
Owner Maintenance
8-39
CX-7_8X59-EA-07E_Edition3 Page331
Wednesday, July 25 2007 3:19 PM
Form No.8X59-EA-07E

Black plate (332,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs: When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children: Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Replacing a headlight bulb
High-beam bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood. 3. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the High-beam bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
4. Disconnect the bulb from the electrical connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
5. Install the new bulb in the reverse orderof removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Make sure the headlight switch is off.
8-40
Maintenance and Care
Owner Maintenance
CX-7_8X59-EA-07E_Edition3 Page332
Wednesday, July 25 2007 3:19 PM
Form No.8X59-EA-07E

Black plate (400,1)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R (SAE)
Headlights High beam
60HB3 (#9005)
Low beam Halogen
55H7 (H7)
Xenon fusion 35D2S (―)
Front turn signal lights/Parking lights 27/8―(#1157NA)
Front side-marker lights 5W5W (#168)
Fog lights
í55 H11 (H11)
High-mount brake light*12.4 ―(― )
Rear turn signal lights 21WY21W (―)
Brake lights/Taillights 21/5W21/5W (#7743)
Reverse lights 21W21W (#7440)
License plate lights 5W5W (#168)
Rear side-marker lights 5W5W (#168)
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
Interior light
Light bulb Category
Wattage ECE R
Overhead lights/Map lights (Front) 5W5W
Overhead light (Rear) 10―
Luggage compartment light 10―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally fitted to
your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure.
Refer to Tire Inflation Pressure on page 8-34.
Standard tire
(Except Mexico)
Tire size Inflation pressure
Front Rear
P235/60R18 102H 220 kPa (32 psi)220 kPa (32 psi)
10-6íSome models.
Specifications
CX-7_8X59-EA-07E_Edition3 Page400
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E

Black plate (406,1)
F
Fuses ................................................. 8-45Panel description ........................ 8-47
Replacement ............................... 8-45
G
Glove Box ......................................... 6-53
H
Hazard Warning Flasher .................... 5-60
Hazardous Driving .............................. 4-7
HeadlightsControl ....................................... 5-53
Flashing ...................................... 5-55
High-low beam .......................... 5-55
Leveling ..................................... 5-55
On reminder ............................... 5-54
Hood Release .................................... 3-39
Horn .................................................. 5-60
I
Ignition Keys ........................................... 3-20
Switch .......................................... 5-2
Illuminated Entry System ................. 6-47
Immobilizer System
(with Advanced Key) ........................ 3-46
Immobilizer System
(without Advanced Key) ................... 3-48
I
Indicator Lights ................................. 5-38 Cruise ......................................... 5-51
Headlight high-beam .................. 5-49
Security ...................................... 5-49
Shift position .............................. 5-49
TCS OFF .................................... 5-50
TCS/DSC ................................... 5-50
Turn-signal/hazard warning ....... 5-51
Information Display .......................... 6-49 Ambient temperature display ..... 6-50
Audio display ............................. 6-51
Climate control display .............. 6-51
Clock .......................................... 6-50
Information display functions .... 6-49
Instrument Cluster ............................. 5-33
Interior Care ...................................... 8-55
Interior Lights ................................... 6-47
J
Jump-Starting .................................... 7-14
K
Keyless Entry System ....................... 3-21
Keys .................................................. 3-20
L
Label Information ............................. 10-2
Lane-Change Signals ........................ 5-56
Liftgate .............................................. 3-28
Luggage compartment ............... 3-29
Light Bulbs Replacement ............................... 8-39
Specifications ............................. 10-6
Lighting Control ............................... 5-53
Lubricant Quality .............................. 10-4
11-4
Index
CX-7_8X59-EA-07E_Edition3 Page406
Wednesday, July 25 2007 3:20 PM
Form No.8X59-EA-07E