low beam MAZDA MODEL CX-7 2009 Owners Manual (in English)

Black plate (197,1)
Signal Warning/Indicator Lights Page
Seat Belt Warning Light/Beep 5-43
Door-Ajar Warning Light 5-44
Low Washer Fluid Level Warning Light 5-44
Automatic Transaxle Warning Light 5-45
AWD Warning Light 5-45
Tire Pressure Monitoring System Warning Light 5-45
KEY Warning Light (Red)/KEY Indicator Light (Green) 5-47
Security Indicator Light 5-49
Headlight High-Beam Indicator Light 5-49
Shift Position Indicator Light 5-49
TCS/DSC Indicator Light 5-50
TCS OFF Indicator Light 5-50
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 5-51
Light-On Indicator Light 5-51
Turn Signal/Hazard Warning Indicator Lights 5-51
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-39
CX-7_8Z60-EA-08D_Edition2 Page197
Friday, May 30 2008 5:27 PM
Form No.8Z60-EA-08D

Black plate (207,1)
NOTE
The advanced key can be set so that the KEY
indicator light (green) does not flash even if
the battery power is low.
Refer to Setting Change (Function
Customization)(page 3-19).
qSecurity Indicator Light
This indicator light starts flashing every 2
seconds when the ignition switch is turned
from the ON to the ACC position and the
immobilizer system is armed.
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:lThe high-beam headlights are on.lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
This indicates the selected shift position
when the ignition switch is in the ON
position.
Gear position indicator
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-49
CX-7_8Z60-EA-08D_Edition2 Page207
Friday, May 30 2008 5:27 PM
Form No.8Z60-EA-08D

Black plate (212,1)
CAUTION
Do not shade the light sensor by
adhering a sticker or a label on the
windshield, or putting an object on it.
Otherwise the light sensor will not
operate correctly.
Sensor
NOTElWhen the headlight switch is in the AUTO
position and the ignition switch is turned to
the ACC or LOCK position, the headlights,
other exterior lights and dashboard
illumination will turn off.
lThe timing for turning on the headlights,
other exterior lights and dashboard
illumination can be delayed by adjusting
the sensitivity of the light sensor. Consult an
Authorized Mazda Dealer regarding sensor
adjustment.
Xenon fusion headlight bulbsí
The low-beam bulbs of the headlights
have xenon fusion bulbs that produce a
bright white beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
NOTE
If the headlights flicker, or the brightness
weakens, the bulb-life may be depleted and a
replacement is necessary. Consult an
Authorized Mazda Dealer.
qLights-On Reminder
If lights are on and the key is removed
from the ignition switch, a continuous
beep sound will be heard when the
driver's door is opened.
NOTE
When the advanced keyless function is used
and the start knob is in the ACC position, the
overrides the lights-on reminder.
5-54
Driving Your Mazda
íSome models.
Switches and Controls
CX-7_8Z60-EA-08D_Edition2 Page212
Friday, May 30 2008 5:27 PM
Form No.8Z60-EA-08D

Black plate (213,1)
qHeadlight High-Low Beam
Push the lever forward for high beam.
Pull back to original position for low
beam.
High beam
Low beam
qFlashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch does
not need to be on, and the lever will return
to the normal position when released.
qHeadlight Levelingí
The number of passengers and weight of
cargo in the luggage compartment change
the angle of the headlights.
The headlight leveling switch adjusts this
angle.
Select the proper setting from the following chart.
Front seat
Rear
seatLoadSwitch
Position
Driver Passenger
×―――0
××――0
×× ×―1
×× ×× 2
×――×3
×: Yes
―:No
qDaytime Running Lights (Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The Daytime Running Lights turn off when the
parking brake is applied.
Driving Your Mazda
Switches and Controls
5-55íSome models. CX-7_8Z60-EA-08D_Edition2 Page213
Friday, May 30 2008 5:27 PM
Form No.8Z60-EA-08D

Black plate (375,1)
Light Bulbs
Headlights (Low beam) Headlights (High beam)
High-mount brake lightFog lights
Front turn signal lights/Parking lightsSide turn signal lights
License plate lights
Brake lights/Taillights Overhead light/Map lights (Front) Overhead light (Rear)
Front side marker lights
Rear turn signal lights
Rear side marker lights
Reverse lights
Luggage compartment light
Some models.
Maintenance and Care
Owner Maintenance
8-39
CX-7_8Z60-EA-08D_Edition2 Page375
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D

Black plate (376,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Replacing a headlight bulb
High-beam bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood.3. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the High-beam bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
4. Disconnect the bulb from the electrical
connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
5. Install the new bulb in the reverse order
of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Make sure the headlight switch is off.
8-40
Maintenance and Care
Owner Maintenance
CX-7_8Z60-EA-08D_Edition2 Page376
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D

Black plate (377,1)
2. If you are changing the right Low-
beam bulb, start the engine, turn the
steering wheel all the way to the right,
and turn off engine. If you are
changing the left Low-beam bulb, turn
the steering wheel to the left.
3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Detach the electrical connector from
the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.7. Swing the retaining spring out and
away to free the bulb.
Sealing
cover
8. Carefully remove the bulb from the
socket by pulling it straight back.
9. Replace the bulb.
10. Install the new bulb in the reverse
order of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Maintenance and Care
Owner Maintenance
8-41
CX-7_8Z60-EA-08D_Edition2 Page377
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D

Black plate (384,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
18 FOG 20 A Fog lights
í
19 DEF 30 A Rear window defroster
20 TNS 15 A Parking lights, License plate lights, Illuminated entry system
21 A/C 10 A Air conditioner
í
22 ETC 20 A Accelerator position sensor
23 H/L HI 15 A Headlight high beam
24 DRL 15 A DRL
í
25 H/L LO RH 15 A Headlight low beam (RH)
26 H/L LO LH 15 A Headlight low beam (LH)
27 ENG BAR 2 7.5 A PCM
28 ECM 10 A Engine control system
29 ENG BAR 1 15 A Air flow sensor, EGR control valve
30 P.WIND 2 20 A Power windows
31 STOP 10 A Brake lights
32 HORN 20 A Horn
33 ENG B+ 25 A PCM
34 HAZARD 10 A Hazard warning flashers, Turn signals
8-48
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8Z60-EA-08D_Edition2 Page384
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D

Black plate (444,1)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage ECE R (SAE)
HeadlightsHigh beam 60 HB3 (#9005)
Low beamHalogen 55 H7 (H7)
Xenon fusion 35 D2S (D2S)
Front turn signal lights/Parking lights 27/8―(#1157NA)
Front side-marker lights 5 W5W (#168)
Fog lights
í55 H11 (H11)
Side turn signal lights (Integrated with outside mirrors)íLED*1―(―)
High-mount brake light LED*1―(―)
Rear turn signal lights 21 WY21W (―)
Brake lights/Taillights 21/5 W21/5W (#7743)
Reverse lights 21 W21W (#7440)
License plate lights 5 W5W (#168)
Rear side-marker lights 5 W5W (#168)
*1 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulbCategory
Wattage ECE R
Overhead lights/Map lights (Front) 5 W5W
Overhead light (Rear) 10―
Luggage compartment light 10―
Vanity mirror light 2―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally fitted to
your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure.
Refer to Tire Inflation Pressure on page 8-34.
Standard tire
(Except Mexico)
Tire sizeInflation pressure
Front Rear
P235/60R18 102H 220 kPa (32 psi) 220 kPa (32 psi)
10-6íSome models.
Specifications
CX-7_8Z60-EA-08D_Edition2 Page444
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D

Black plate (450,1)
F
Fog Lights ......................................... 5-56
Front ........................................... 5-56
Foot Brake .......................................... 5-5
Front Seats
(Electrically Operated Seats) ............... 2-4
Front Seats
(Manually Operated Seats) ................. 2-2
Fuel
Filler lid and cap ........................ 3-41
Gauge ......................................... 5-36
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-45
Panel description ........................ 8-47
Replacement ............................... 8-45
G
Glove Box ......................................... 6-89
H
Hazard Warning Flasher .................... 5-60
Hazardous Driving .............................. 4-7
Headlights
Control ....................................... 5-53
Flashing ...................................... 5-55
High-low beam .......................... 5-55
Leveling ..................................... 5-55
On reminder ............................... 5-54
HomeLink Wireless Control
System .............................................. 5-61
Hood Release .................................... 3-42
Horn .................................................. 5-60
I
Ignition
Keys ........................................... 3-21
Switch .......................................... 5-2
Illuminated Entry System ................. 6-83
Immobilizer System
(with Advanced Key) ........................ 3-49
Immobilizer System
(without Advanced Key) ................... 3-51
Indicator Lights ................................. 5-38
Cruise ......................................... 5-51
Headlight high-beam .................. 5-49
Security ...................................... 5-49
Shift position .............................. 5-49
TCS OFF .................................... 5-50
TCS/DSC ................................... 5-50
Turn-signal/hazard warning ....... 5-51
Information Display .......................... 6-85
Ambient temperature display ..... 6-86
Audio display ............................. 6-87
Climate control display .............. 6-87
Clock .......................................... 6-86
Information display functions .... 6-85
Instrument Cluster ............................. 5-33
Interior Care ...................................... 8-55
Interior Lights ................................... 6-83
J
Jump-Starting .................................... 7-14
K
Keyless Entry System ....................... 3-22
Keys .................................................. 3-21
L
Label Information ............................. 10-2
11-4
Index
CX-7_8Z60-EA-08D_Edition2 Page450
Friday, May 30 2008 5:29 PM
Form No.8Z60-EA-08D