MAZDA MODEL CX-9 2007 Owners Manual (in English)

Black plate (421,1)
NOTElTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Low-beam bulb
(Xenon fusion bulb)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
1. Make sure the headlight switch is off.
2. Lift the hood.
3. Remove the attachment bolts and the
coolant reservoir before replacing the
light bulb.
4. Turn the cover counterclockwise and
remove it.
5. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector downward.
6. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
7. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-39
CX-9_8V83-EA-06I_Edition3 Page421
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (422,1)
8. Install the coolant reservoir. If you are
unsure of how tight the bolts should be,
have them inspected at an Authorized
Mazda Dealer.
Bolt tightening torque
N·m (kgf·m, ft·lbf)6.9―11.8
(0.7―1.2, 5.1―8.7)
NOTElTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Front side marker lights, Front turn
signal lights
1. Make sure the headlight switch is off.
2. Lift the hood.
3. Remove the attachment bolts and the
coolant reservoir before replacing the
light bulb.
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.Front side marker lights
Front turn signal lights
6. Install the new bulb in the reverse order
of removal.
7. Install the coolant reservoir. If you are
unsure of how tight the bolts should be,
have them inspected at an Authorized
Mazda Dealer.
Bolt tightening torque
N·m (kgf·m, ft·lbf)6.9―11.8
(0.7―1.2, 5.1―8.7)
Fog lightsí
1. Make sure the headlight switch is off.
2. Turn the screws counterclockwise and
remove them.
8-40
Maintenance and Care
íSome models.
Owner Maintenance
CX-9_8V83-EA-06I_Edition3 Page422
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (423,1)
3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then remove the mudguard.
Removal
Installation
4. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector downward.
5. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the bulb from its
socket in the reflector by gently pulling
it straight backward out of the socket.
6. Install the new bulb in the reverse order
of removal.NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
Side turn signal lightsí, Brake lights,
Taillights (Rear combination light side),
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
Rear turn signal lights/Rear side-
marker light
1. Turn the bolts counterclockwise and
remove them.
Maintenance and Care
Owner Maintenance
8-41íSome models. CX-9_8V83-EA-06I_Edition3 Page423
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (424,1)
2. Pull the unit rearward to remove it.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
Rear side-maker
light
Rear direction indication light
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
Taillights (Liftgate side), Reverse lights
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Reverse light
Taillight
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an Authorized
Mazda Dealer.
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
8-42
Maintenance and Care
Owner Maintenance
CX-9_8V83-EA-06I_Edition3 Page424
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (425,1)
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front),
Overhead light (Center, Rear), Luggage
compartment light, Courtesy lights,
Vanity mirror lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light/Map lights (Front)
Overhead light (Center, Rear)
Luggage compartment light
Edge
Courtesy lights
Maintenance and Care
Owner Maintenance
8-43
CX-9_8V83-EA-06I_Edition3 Page425
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (426,1)
Vanity mirror lights
3. Install the new bulb in the reverse order
of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing fuses located behind the
glove box
If an electrical system is inoperative,
inspect the fuses located behind the glove
box.
1. Turn off the ignition switch and other
switches.
2. Open the glove box.
3. Remove the cover.
8-44
Maintenance and Care
Owner Maintenance
CX-9_8V83-EA-06I_Edition3 Page426
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (427,1)
Fuse
4. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
5. Inspect the fuse and replace it if it's
blown.
NormalBlown
6. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an expert
repairer install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the ROOM circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover or the
relay box cover.
Fuse block
Maintenance and Care
Owner Maintenance
8-45
CX-9_8V83-EA-06I_Edition3 Page427
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (428,1)
Relay box
3. If any fuse but the MAIN fuse is
blown, replace it with a new oneof the
same amperage rating.
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
8-46
Maintenance and Care
Owner Maintenance
CX-9_8V83-EA-06I_Edition3 Page428
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (429,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 MAIN 150A For protection of all circuits
2 ENGINE 20A Transaxle control system
3 R HEATER 40A Heater
4 P.SEAT R 30A Power seat (RH)
í
5 HEATER 50A Heater
6 IGKEY2 40A For protection of various circuits
7 FAN130A
íCooling fan
40Aí
8 P.SEAT L 40A Power seat (LH)í
9 DEFOG 30A Rear window defroster
10 BTN 40A For protection of various circuits
11 FUEL PUMP 30A Fuel pump
12 IGKEY1 30A For protection of various circuits
13 FOG 15A Fog lights
í
14 ABS (SOL) 30A ABS solenoid
15 D/L 25A Power door locks
16 ROOM 15A Overhead light
Maintenance and Care
Owner Maintenance
8-47íSome models. CX-9_8V83-EA-06I_Edition3 Page429
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I

Black plate (430,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
17 OUTLET CTR 15A Accessory socket (Center)
18 OUTLET RR 15A Accessory socket (Rear)
19 AC PWR 15A Moon roof
í, DC/AC inverter
20 S.WARM 15A Seat warmerí
21 A/C MAG 10A Air conditioner
22 BOSE 25A Audio system (Bose®Sound System-equipped model)í
23 FAN230AíCooling fan
40Aí
24 ABS 50A ABS
25 IG COIL 25A Ignition system
26 H/L LOW L 15A Headlight-left (Low beam)
27 H/L LOW R 15A Headlight-right (Low beam)
28 H/L HIGH 20A Headlight-high (High beam)
29 HAZARD 15A Hazard warning flashers
30 ENG +B 10A PCM
31 HORN 15A Horn
32 STOP 7.5A Brake lights
33 EGI INJ 10A Engine control system
34 ENG BAR 20A Air flow sensor, EGR control valve
35 ENG BAR 2 7.5A PCM
8-48
Maintenance and Care
íSome models.
Owner Maintenance
CX-9_8V83-EA-06I_Edition3 Page430
Monday, February 26 2007 7:21 PM
Form No.8V83-EA-06I