trunk MAZDA MODEL CX-9 2009 Navigation Manual (in English)

94
Before
UseGetting
started
RoutingAddress
Book
Vo i c e Recognition
Navigation
Set Up
RDM-TMC
Audio Operation
Navigation
Set Up
Yes: Available
No: Not available
Bluetooth is the registered trademark of Bluetooth SIG. Inc.
Note
l
It may not be possible to play a Bluetooth audio device if it is placed anywhere transmission
is compromised, such as inside a metal container or the trunk. Move the Bluetooth audio
device to a location where transmission is possible.
l Battery consumption of Bluetooth audio devices is higher while Bluetooth-connected.
l If a non-Bluetooth device is to be used, a commercially-available Bluetooth adapter is
required. When playing an audio device with a Bluetooth adapter installed, programming of
the audio device may not be possible or audio may not be heard from the vehicle speakers
if the connection of the adapter and the device is poor. If this happens, check if the
Bluetooth adapter is properly connected.
nBluetooth audio device programming
Any Bluetooth audio device must be programmed to the vehicle’s Bluetooth unit before it can
be listened to over the vehicle’s speakers.
A maximum of seven devices including Bluetooth audio devices and hands-free mobile
phones can be programmed to one vehicle.
Note
lAlways perform Bluetooth audio device programming while the vehicle is stopped.
l If a Bluetooth device has already been programmed to the vehicle as a hands-free mobile
phone, it does not need to be programmed again when using the device as a Bluetooth
audio device. Conversely, it does not need to be programmed again as a hands-free mobile
phone if it has already been programmed as a Bluetooth audio device.
l The transmission range of a Bluetooth audio device is about 10 m (32 ft).
l Therefore, if there is another Bluetooth audio device within a 10 m (32 ft) radius of the
vehicle, the device may be identified and programmed instead.
Concerning the operation of a Bluetooth audio device itself, refer to its instruction manual.
Some Bluetooth audio devices have PIN codes (four digits). Refer to the audio device’s
instruction manual because the programming procedure differs depending on whether it has
a PIN code or not. Function A2DP A2DP+AVRCP
Playback No Yes
Pause No Yes
File(Track)
up/down No Yes
2%:':9)FSSO4EKI1SRHE].YRI41

115
Before
UseGetting
started
RoutingAddress
Book
Vo i c e Recognition
Navigation
Set Up
Bluetooth Hands-Free
Note
l
If the ignition switch is turned off during a hands-free call, the line is transferred to the
mobile telephone automatically.
l If the mobile telephone is in a location where radio reception is difficult such as a metal
container or in the trunk, the call may not be connected using Bluetooth. If communication is
not possible, change the location of the mobile telephone.
nMobile telephone programming
To use Bluetooth Hands-Free, the phone has to be programmed to the hands-free unit using
the following procedure.
A maximum of seven devices including hands-free mobile phones and Bluetooth audio
devices can be programmed to one vehicle. Refer to “Bluetooth audio device programming”.
( page 94)
Note
lA mobile telephone can be programmed only when the vehicle is parked.
l If a Bluetooth device has already been programmed to the vehicle as a Bluetooth audio
device, it does not need to be programmed again when using the device as a hands-free
mobile phone. Conversely, it does not need to be programmed again as a Bluetooth audio
device if it has already been programmed as a hands-free mobile phone.
l Since the communication range of a Bluetooth equipped mobile telephone is about 10
meters (32 ft), if a mobile telephone is placed within a 10-meter (32\
ft) radius of the vehicle,
it may be detected/programmed unintentionally while another telephone is being
programmed.
nDeleting the link to a Mobile telephone
Refer to “Deleting the link to a Bluetooth audio device”. ( page 96)
nChanging the registered mobile telephone
Refer to “Changing the registered Bluetooth device”. ( page 98)
2%:':9)FSSO4EKI1SRHE].YRI41