light MAZDA MODEL CX-9 2014 Owners Manual (in English)

Black plate (213,1)
qBlind Spot Monitoring (BSM)
The Blind Spot Monitoring (BSM) system monitors the detection areas on both sides of the
vehicle to the rear and when there are vehicles in the detection area it notifies the driver by
illuminating the Blind Spot Monitoring (BSM) warning light while the vehicle speed is
about 10 km/h (6.2 mph) or faster and driving forward.
If the turn signal lever is operated to the side the Blind Spot Monitoring (BSM) warning
light is illuminated, the Blind Spot Monitoring (BSM) warning light flashes and the system
warns the driver of the vehicle in the detection area using a BSM warning beep sound.
Detection areas
Your vehicle
Driving Your Mazda
Starting and Driving
5-37
CX-9_8DA3-EA-13G_Edition2 Page213
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (214,1)
NOTElThe Blind Spot Monitoring (BSM) does not operate when the vehicle speed is lower than about 10
km/h (6.2 mph).
lThe detection area of the Blind Spot Monitoring (BSM) has been determined based on the lane
width of general freeways. Therefore on a road with a narrower lane width, the system may detect
vehicles on a lane next to the adjacent lane and operate the warning light/beep. On a road with
wider lane width, the system may not detect vehicles on the adjacent lane and may not operate the
warning light/beep.
lUnder the following conditions, the system may be unable to detect vehicles, or detection may be
delayed.
lThe vehicle accelerates from a standing-start with a vehicle alongside.lA vehicle moves from a lane two lanes over to the adjacent lane.lThe difference in vehicle speed between your vehicle and another vehicle is larger when
passing or being passed, and the vehicle passes the detection area within a short period of
time.
lOn a steep incline, or when there is a difference in height between lanes.lImmediately after the system has been activated by pressing the Blind Spot Monitoring (BSM)
OFF switch again after it has been turned off (Blind Spot Monitoring (BSM) OFF indicator
light in instrument panel illuminates) by pressing the switch.
lThe selector lever is shifted to the R position, or directly after being shifted from the R position.lThe system may not operate normally when towing a trailer. Turn off the system by operating the
Blind Spot Monitoring (BSM) OFF switch when towing a trailer.
lThe system switches to the Rear Cross Traffic Alert function when the selector lever is shifted to
the R position.
5-38
Driving Your Mazda
Starting and Driving
CX-9_8DA3-EA-13G_Edition2 Page214
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (215,1)
qRear Cross Traffic Alert (RCTA)
When reversing the vehicle from a parking garage, vehicles approaching both sides of the
vehicle are detected to alert the driver of a possible collision by flashing the Blind Spot
Monitoring (BSM) warning light and activating the Blind Spot Monitoring (BSM) warning
beep sound.
Detection areas
Your vehicle
Rear Cross Traffic Alert (RCTA) system operation
1. The Rear Cross Traffic Alert (RCTA) system operates when the selector lever is shifted
to the R position.
(With rearview monitor)
The rearview monitor is displayed.
Driving Your Mazda
Starting and Driving
5-39
CX-9_8DA3-EA-13G_Edition2 Page215
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (216,1)
2. If a vehicle approaches which may hit you, the Blind Spot Monitoring (BSM) systemwarning light flashes and the Blind Spot Monitoring system (BSM) warning beep
sounds at the same time.
(With rearview monitor)
The Rear Cross Traffic Alert (RCTA) warning indication in the rearview monitor also
synchronizes with the Blind Spot Monitoring (BSM) system warning light on the door
mirrors.
(With rearview monitor)
5-40
Driving Your Mazda
Starting and Driving
CX-9_8DA3-EA-13G_Edition2 Page216
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (217,1)
NOTE
Under the following conditions, the system may be unable to detect vehicles, or detection may be
delayed.
lThe vehicle is reversed at a speed of 12 km/h or fasterlThe radar is obstructed by objects such as a large vehicle parked adjacently or by a wall.
(Reverse vehicle to position in which radar is not obstructed.)
Your vehicle
lA vehicle approaches from straight behind
Your vehicle
lThe vehicle is parked at a highly acute angle
Your vehicle
lImmediately after the system has been activated by pressing the Blind Spot Monitoring (BSM)
OFF switch again after it has been turned off (Blind Spot Monitoring (BSM) OFF indicator light
in instrument panel illuminates) by pressing the switch.
Driving Your Mazda
Starting and Driving
5-41
CX-9_8DA3-EA-13G_Edition2 Page217
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (218,1)
qBSM Warning Light/Beep
BSM warning light
Equipped on the left and right door
mirrors.
This warning light illuminates for a few
seconds when the ignition is switched
ON.
Driving forward
If the Blind Spot Monitoring (BSM)
system detects a vehicle in the detection
area while the vehicle is driven at a speed
of about 10 km/h (6.2mph) or more, the
BSM warning light illuminates on the side
of the vehicle where the rear on-coming
vehicle is detected. A warning indicator
light flashes when the turn signal lever is
operated to the side where the BSM
warning lights is illuminated to alert the
driver.
Reversing
If vehicles approach from the rear on the
left and right, the BSM warning lights on
both sides flash. NOTE
lIf ice or snow adhere to the outer mirror
surface, the BSM warning light may not be
visible.
lIf the door window glass is tinted, it may
affect the visibility of the BSM warning
light, making it difficult to confirm the
illumination of the light.
BSM warning beep
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the BSM warning light is illuminated.
NOTE
The system can be personalized so that the
BSM warning beep does not operate. Refer to
Personalization Features on page 10-8.
Reversing
If vehicles approach from the rear on the
left and right, the BSM warning beep
operates.
q
BSM OFF Indicator Light
This indicator light illuminates for a few
seconds when the ignition is switched
ON.
The BSM OFF indicator light illuminates
when the BSM system is turned off by
pressing the BSM OFF switch.
The indicator light flashes if the BSM
system has a malfunction. Consult an
Authorized Mazda Dealer.
5-42
Driving Your Mazda
Starting and Driving
CX-9_8DA3-EA-13G_Edition2 Page218
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (219,1)
NOTE
If the vehicle is driven on a road with less
traffic and few vehicles that the radar sensors
can detect, the system may pause (The BSM
OFF indicator light in the instrument panel
flashes). However, it does not indicate a
malfunction.
qBSM OFF Switch
When the BSM switch is pressed, the
BSM system turns off and the BSM OFF
indicator light illuminates.
Press the BSM OFF switch again to turn
on the BSM system. The BSM OFF
indicator light turns off.
NOTE
lThe system may not operate normally when
towing a trailer. Turn off the system by
operating the BSM OFF switch when
towing a trailer.
lIf the ignition is switched off with the BSM
system turned off, the system becomes
operable automatically when the ignition is
switched ON.
qCare of Radar Sensors
The radar sensors are equipped inside the
rear bumper.
Radar sensors
Always keep the bumper surface near the
radar sensor area clean so that the BSM
system operates normally. Refer to the
Exterior Care (page 8-56).
NOTE
lThe BSM OFF indicator light flashes if the
radar sensors cannot operate normally. If
the light remains flashing after cleaning the
bumper surface near the radar sensor area,
consult an Authorized Mazda Dealer.
lFor repairs or paintwork around the radar
sensors, or replacement of the bumper,
consult an Authorized Mazda Dealer.
Driving Your Mazda
Starting and Driving
5-43
CX-9_8DA3-EA-13G_Edition2 Page219
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (223,1)
NOTElDo not install any accessories within the detection ranges of the sensors. It may affect the system
operation.
lDepending on the type of obstruction and the surrounding conditions, the detection range of a
sensor may narrow, or the sensors may not be able to detect obstructions.
lThe system may not operate normally under the following conditions:lMud, ice, or snow is adhering to the sensor area (Returns to normal operation when removed).lThe sensor area is frozen (Returns to normal operation when the ice is thawed).lThe sensor is covered by a hand.lThe sensor is excessively shocked.lThe vehicle is excessively tilted.lUnder extremely hot or cold weather conditions.lThe vehicle is driven on bumps, inclines, gravel, or grass covered roads.lAnything which generates ultrasound is near the vehicle, such as another vehicle's horn, the
engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or another vehicle's
sensors.
lThe vehicle is driven in heavy rain or in road conditions causing water-splash.lA commercially-available fender pole or an antenna for a radio transmitter is installed to the
vehicle.
lThe vehicle is moving towards a tall or square curbstone.lAn obstruction is too close to the sensor.lObstructions under the bumper may not be detected. Obstructions that are lower than the bumper
or thin which may have been initially detected but are no longer detected as the vehicle
approaches more closely.
lThe following types obstructions may not be detected:lThin objects such as wire or ropelThings which absorb sonic waves easily such as cotton or snowlAngular shaped objectslVery tall objects, and those which are wide at the toplSmall, short objectslAlways have the system inspected at an Authorized Mazda Dealer if any shock is applied to the
bumpers, even in a minor accident. If the sensors are deviated, they cannot detect obstructions.
lThe system may have a malfunction if the beep does not operate or the indicator light does not
illuminate when the park assist sensors switch is turned on. Consult an Authorized Mazda Dealer.
lThe system may have a malfunction if the beep sound which indicates a system malfunction is
heard and the indicator light flashes. Consult an Authorized Mazda Dealer.
lThe beeper which indicates a system malfunction may not be heard if the ambient temperature is
extremely cold, or mud, ice, or snow adheres to the sensor area. Remove any foreign material
from the sensor area.
Driving Your Mazda
Starting and Driving
5-47
CX-9_8DA3-EA-13G_Edition2 Page223
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (224,1)
qSensor Detection Range
The sensors detect obstructions within the following range.
Rear sensor detection range
Rear corner sensor detection range
A
Unit: cm (in)
B A: About 150 (About 59.1)
B: About 150 (About 59.1)
q
Park Assist Sensors Switch
The switch can be activated when the ignition is switched ON, the shift lever is in any
position except reverse (R), and the vehicle speed is about 10 km/h (6 mph) or less.
When the parking sensor switch is pressed, a beep sound is heard and the indicator light in
the switch illuminates.
NOTE
If the system is cancelled, it will not restore automatically even when the vehicle speed is decreased to
10 km/h (6 mph) or less.
5-48
Driving Your Mazda
Starting and Driving
CX-9_8DA3-EA-13G_Edition2 Page224
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G

Black plate (231,1)
qFuel Gauge
The fuel gauge shows approximately how
much fuel is remaining in the tank when
the ignition is switched ON.
We recommend keeping the tank over 1/4
full. When the low fuel warning light
illuminates or when the needle is near E,
refuel as soon as possible.
Full
Approx. 1/4 FullLow fuel
warning light
NOTElAfter refueling, it may require some time for
the needle to stabilize. In addition, the
needle may deviate while driving on a slope
or curve since the fuel moves in the tank.
lThe direction of the arrow () next to the
low fuel warning light indicates that the
fuel-filler lid is on the left side of the
vehicle.
q Dashboard Illumination
Rotate the knob to adjust the brightness of
the instrument cluster and other
illuminations in the dashboard.
NOTE
lThe brightness of dashboard illuminations
can be adjusted when the headlight switch
is in the
orposition.lWhen the dashboard illumination
brightness cannot be adjusted any more, a
beep sound will be heard.
Dim
Bright
Canceling the illumination dimmer
(Black-out meter and dashboard
illuminations)
When the headlight switch is in the
orposition, the illumination of the
instrument cluster and the information
display dims.
When driving on snowy or foggy roads,
or in other situations when the instrument
cluster or information display's visibility
is reduced due to glare from surrounding
brightness, cancel the illumination
dimmer and increase the illumination
intensity.
To cancel the illumination dimmer, press
the dashboard illumination knob.
NOTE
lThis symbol () indicates the knob to
adjust the brightness of the dashboard
illumination.
lIf the illumination dimmer is cancelled, the
instrument cluster and the information
display will not dim when the headlight
switch is turned to the
orposition
again. Press the dashboard illumination
knob to activate the illumination dimmer.
Driving Your Mazda
Instrument Cluster and Indicators
5-55
CX-9_8DA3-EA-13G_Edition2 Page231
Monday, September 9 2013 4:8 PM
Form No.8DA3-EA-13G