light MAZDA MODEL CX-9 2022 Owners Manual

If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will cause the
system to not operate correctly. Consequently, each system may not operate normally
which could lead to an unexpected accident.
 Do not disassemble or modify the Forward Sensing Camera (FSC).
Disassembly or
modification of the Forward Sensing Camera (FSC) will cause a malfunction
or mistaken operation. Consequently, each sy stem may not operate normally which could
lead to an unexpected accident.
 Heed the following cautions to assure the correct operation of the Forward Sensing Camera
(FSC).
 Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get dirty.
 Do not remove the Forward Sensing Camera (FSC) cover.
 Do not place objects on the dashboard which reflect light.
 Always keep the windshield glass around the camera clean by removing dirt or fogging.
Use the windshield defroster to remove fogging on the windshield.
 Consult an Authorized Mazda Dealer regardi ng cleaning the interior side of the
windshield around the Forw ard Sensing Camera (FSC).
 Consult an Authorized Mazda Dealer before performing repairs around the Forward
Sensing Camera (FSC).
 The Forward Sensing Camera (FSC) is installe d to the windshield. Consult an Authorized
Mazda Dealer for windshield repair and replacement.
 When cleaning the wind shield, do not allow glass cleaners or similar cleaning fluids to
get on the Forward Sensing Camera (FSC) le ns. In addition, do not touch the Forward
Sensing Camera (FSC) lens.
 When performing repairs around the rearv iew mirror, consult an Authorized Mazda
Dealer.
 Consult an Authorized Mazda Dealer regarding cleaning of the camera lens.
 Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If the Forward Sensing Camera (FSC) is severely hit or if there are cracks or damage
caused by flying gravel or debris in the area around it, stop using the following systems
and consult an Authorized Mazda Dealer.
 High Beam Control System (HBC)
 Driver Attention Alert (DAA)
 Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS)
 Traffic Sign Recognition System (TSR)
 Advanced Smart City Brak e Support (Advanced SCBS)
 Smart City Brake Support [Forward] (SCBS F)
 Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function)
 Smart Brake Support (SBS)
When Driving
i-ACTIVSENSE
4-224
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

The direction in which the Forward Sensing Camera (FSC) is pointed has been
finely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
 Always use tires for all wheels that are of the specified size, and the same manufacturer,
brand, and tread pattern. In addition, do no t use tires with significantly different wear
patterns on the same vehicle as the system may not operate normally.
 The Forward Sensing Camera (FSC) includes a function for detecting a soiled windshield
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windshield . In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
ï‚·In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
ï‚·The height of the vehicle ahead is low.
ï‚·You drive your vehicle at the same speed as the vehicle ahead.
ï‚·Headlights are not turned on during the night or when going through a tunnel.
ï‚·In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
ï‚·Under bad weather condition, such as rain, fog and snow.
ï‚·The window washer is being used or the windshield wipers are not used when it's
raining.
ï‚·Ice, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windshield.
ï‚·Trucks with low loading platforms and vehicl es with an extremely low or high profile.
ï‚·When driving next to walls with no patterning (including fences and longitudinally
striped walls).
ï‚·The taillights of the vehicle ahead are turned off.
ï‚·A vehicle is outside the illumi nation range of the headlights.
ï‚·The vehicle is making a sharp turn, or ascending or descending a steep slope.
ï‚·Entering or exiting a tunnel.
ï‚·Heavy luggage is loaded causing the vehicle to tilt.
ï‚·Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
ï‚·There are many light emitters on the vehicle ahead.
ï‚·When the vehicle ahead is not equipped with taillights or the taillights are turned off at
nighttime.
ï‚·Elongated luggage or cargo is loaded onto installed roof rails and covers the Forward
Sensing Camera (FSC).
When Driving
i-ACTIVSENSE
4-225
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

ï‚·Exhaust gas from the vehicle in front, sand, snow, and water vapor rising from
manholes and grating, and water splashed into the air.
ï‚·When towing a malfunctioning vehicle.
ï‚·The vehicle is driven with tires having significantly different wear.
ï‚·The vehicle is driven on down slopes or bumpy roads.
ï‚·There are water puddles on the road.
ï‚·The surroundings are dark such as during the night, early evening, or early morning, or
in a tunnel or indoor parking lot.
ï‚·The illumination brightness of the headlights is reduced or the headlight illumination is
weakened due to dirt or a deviated optical axis.
ï‚·The target object enters the blind spot of the Forward Sensing Camera (FSC).
ï‚·A person or object bursts onto the road from the shoulder or cuts right in front of you.
ï‚·You change lanes and approach a vehicle ahead.
ï‚·When driving extremely close to the target object.
ï‚·Tire chains or a temporary spare tire is installed.
ï‚·The vehicle ahead has a special shape. For example, a vehicle towing a trailer house or
a boat, or a vehicle carrier carrying a vehicle with its front pointed rearward.
ï‚·If the Forward Sensing Camera (FSC) cannot operate normally due to backlight or fog,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warn ing lights turn on. However, this does not indicate a
malfunction.
ï‚·High Beam Control System (HBC) warning light (amber)
ï‚·Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
indication
ï‚·Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) warning indication
ï‚·Smart Brake Support/Smart City Brake Support (SBS/SCBS) warning indication
(amber)
ï‚·If the Forward Sensing Camera (FSC) cannot operate normally due to high temperatures,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warn ing lights turn on. However, this does not indicate a
malfunction. Cool down the area around the Forward Sensing Camera (FSC) such as by
turning on the air conditioner.
ï‚·High Beam Control System (HBC) warning light (amber)
ï‚·Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
indication
ï‚·Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) warning indication
When Driving
i-ACTIVSENSE
4-226
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

ï‚·Smart Brake Support/Smart City Brake Support (SBS/SCBS) warning indication
(amber)
ï‚·If the Forward Sensing Camera (FSC) detects that the windshield is dirty or foggy, the
system functions related to the Forward Sensing Camera (FSC) are temporarily stopped
and the following warning lights turn on. However, this does not indicate a problem.
Remove the dirt from the windshield or press the defroster switch and defog the
windshield.
ï‚·High Beam Control System (HBC) warning light (amber)
ï‚·Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
indication
ï‚·Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) warning indication
ï‚·Smart Brake Support/Smart City Brake Support (SBS/SCBS) warning indication
(amber)
ï‚·If there are recognizable cracks or damage caused by flying gravel or debris on the
windshield, always have the windshield replaced. Consult an Authorized Mazda Dealer
for replacement.
ï‚·(With Advanced Smart City Brake Support (Advanced SCBS))
ï‚·The Forward Sensing Camera (FSC) recognizes pedestrians when all of the following
conditions are met:
ï‚·The height of a pedestrian is about 1 to 2 meters.
ï‚·An outline such as the head, both shoulders, or the legs can be determined.
ï‚·In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly:
ï‚·Multiple pedestrians are walking, or there are groups of people.
ï‚·A pedestrian is close to a separate object.
ï‚·A pedestrian is crouching, lying, or slouching.
ï‚·A pedestrian suddenly jumps into the road right in front of the vehicle.
ï‚·A pedestrian opens an umbrella, or is carrying large baggage or articles.
ï‚·A pedestrian is in a dark location such as during the night, or blends into the
background by wearing clothes matching the background color.
When Driving
i-ACTIVSENSE
4-227
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

Instrument cluster display for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET/
switch and release it immediately.
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is on.
Greater speed will not interfere with or
change the set speed. Take your foot off
the accelerator to return to the set speed.
â–¼To Decrease Cruising Speed
Press the SET/ switch and hold it. The
vehicle will gradually slow.
Release the switch at the desired speed.

Press the SET/
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET/
switch operation
Instrument cluster display for vehicle
speed indicated in km/h: 1 km/h (0.6 mph)
Instrument cluster display for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
â–¼ To Resume Cruising Speed at More
Than 25 km/h (16 mph)
If the cruise contro
l system temporarily
canceled (such as applying the brake
pedal) and the system is still activated, the
most recent set speed will automatically
resume when the RES/
switch is pressed.
If vehicle speed is below 25 km/h (16
mph), increase the vehicle speed up to 25
km/h (16 mph) or more and press the RES/
switch.
â–¼ To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
ï‚·Slightly depress the brake pedal.
ï‚·Press the OFF/CANCEL switch.
If the RES/
switch is pressed when the
vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
ï‚·If any of the following conditions occur,
the cruise control system is temporarily
canceled.
ï‚·The parking brake is applied.
ï‚·The selector lever is in the P or N
position.
ï‚·When the cruise control system is
temporarily canceled by even one of the
applicable cancel conditions, the speed
cannot be re-set.
ï‚·The cruise control cannot be cancelled
while driving in manual mode (selector
lever shifted from D to M position).
Therefore, engine braking will not be
applied even if the transaxle is shifted
down to a lower gear. If deceleration is
required, lower the set speed or depress
the brake pedal.
â–¼ To Deactivate
When a cruising speed has been set
(cruise set indication (green) turns on)
Long-press the OFF/CANCEL switch or
press the OFF/CANCEL switch 2 times.
When Driving
Cruise Control
4-238
CX-9_8KH5-EA-21K_Edition2_old
2021-9-16 14:11:22

Tire Pressure Monitoring System
The Tire Pressure Monitoring System (TPMS) monitors the pressure for each tire.
If tire pressure is to o low in one or more tires, the system will inform the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Contact Authorized Mazda Dealer and Have Vehicle Inspected on page 7-31.
Refer to Taking Action on page 7-36.
Refer to Tire Inflation Pressu re Warning Beep on page 7-48.

The tire pressure sensors installed on each wheel send tire pre ssure data by radio signal to
the receiver unit in the vehicle.
Tire pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tire temperatures are also
lower. When the tire temperature decreases, the air pressure decreases as well. The TPMS
warning light may illumina te more frequently. Visually inspect the tires daily before driving,
and check tire pressures monthly with a tire pressure gauge. When checking tire pressures,
use of a digital tire pressure gauge is recommended.

TPMS does not alleviate your need to check the pressure and con dition of all four tires
regularly.
CAUTION
 Each tire, including the spare (if provided), should be checked monthly when cold and
inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your vehicle has tires of a different size than the
size indicated on the vehicle placard or tire inflation pressure label, you should determine
the proper tire inflation pressure for those tires.)
When Driving
Tire Pressure Monitoring System
4-240
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pre ssure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when th e low tire pressure telltale illuminates, you
should stop and check your tires as soon as possible, and inflate them to the proper
pressure. Driving on a significantly under-in flated tire causes the tire to overheat and can
lead to tire failure. Under-inflation also reduce s fuel efficiency and tire tread life, and may
affect the vehicle's handling and stopping ability.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the
driver's responsibility to maintain correct ti re pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tire pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when
the system is not operating properly.
The TPMS malfunction indicator is combined with the low tire pressure telltale. When the
system detects a malfunction, the telltale wi ll flash for approximately one minute and then
remain continuously illuminated. This sequen ce will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of reasons, including the installation of replacement
or alternate tires or wheels on the vehicle th at prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after replacing one or more tires or wheels on
your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to
continue to function properly.
 To avoid false readings, the system samples fo r a little while before indicating a problem. As
a result it will not instantaneously regi ster a rapid tire deflation or blow out.
â–¼System Error Activation
When the warning light flashes, there may
be a system malfunction. Consult an
Authorized Mazda Dealer.
A system error activation may occur in the
following cases:
ï‚·When there is equipment or a device
near the vehicle using the same radio
frequency as that of the tire pressure
sensors.
ï‚·When a metallic device such as a
non-genuine navigation system is
equipped near the center of the
dashboard, which may block radio
signals from the tire
pressure sensor to
the receiver unit.
ï‚·When using the following devices in the
vehicle that may cause radio
interference with the receiver unit.
ï‚·A digital device such as a personal
computer.
ï‚·A current converter device such as a
DC-AC converter.
ï‚·When excess snow or ice adheres to the
vehicle, especially around the wheels.
ï‚·When the tire pressu re sensor batteries
are exhausted.
ï‚·When using a wheel with no tire
pressure sensor installed.
ï‚·When using tires with steel wire
reinforcement in the sidewalls.
ï‚·When using tire chains.
When Driving
Tire Pressure Monitoring System
4-241
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

â–¼Tires and Wheels
CAUTION
When inspecting or adjusting the tire air
pressures, do not apply excessive force to
the stem part of the wheel unit. The stem
part could be damaged.
Changing tires and wheels
The following procedure allows the TPMS
to recognize a tire pressure sensor's unique
ID signal code whenever tires or wheels
are changed, such as changing to and from
winter tires.
NOTE
Each tire pressure sensor has a unique ID
signal code. The signal code must be
registered with the TPMS before it can
work. The easiest way to do it is to have
an Authorized Mazda Dealer, change your
tire and complete ID signal code
registration.
When having tires changed at an
Authorized Mazda Dealer
When an Authorized Mazda Dealer,
changes your vehicle's tires, they will
complete the tire pressure sensor ID signal
code registration.

When changing tires yourself
If you or someone else changes tires, you
or someone else can also undertake the
steps for the TPMS t
o complete the ID
signal code registration.
1. After tires have been changed, switch the ignition ON, then back to ACC or
OFF.
2. Wait for about 15 minutes.
3. After about 15 minutes, drive the
vehicle at a speed of at least 25 km/h
(16 mph) for 10 minutes and the tire
pressure sensor ID s ignal code will be
registered automatically.
NOTE
If the vehicle is driven within about 15
minutes of changing tires, the tire pressure
monitoring system warn ing light will flash
because the sensor ID signal code would
not have been registered. If this happens,
park the vehicle for about 15 minutes,
after which the sensor ID signal code will
register upon driving the vehicle for 10
minutes.
Replacing tires and wheels
CAUTION
 When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the tire
pressure sensors may be damaged.
 The wheels equipped on your Mazda are
specially designed for installation of the
tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to inst all the tire pressure
sensors.
Be sure to have the tire pressure sensors
installed whenever tires or wheels are
replaced.
When having a tire or wheel or both
replaced, the follow ing types of tire
pressure sensor installations are possible.
ï‚·The tire pressure sensor is removed
from the old wheel and installed to the
new one.
When Driving
Tire Pressure Monitoring System
4-242
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

â–¼Displayable Range on the Screen
The images on the screen may be different from the actual condi
tions.

(Screen display) Garnish
Bumper
(Actual view)
Object
Obstruction detection
indication in parking
sensor system
Some models
NOTE
ï‚·The displayable range varies depending on the vehicle and road conditions.
ï‚·The displayable range is limited. Objects under the bumper or around the bumper ends
cannot be displayed.
ï‚·The distance appearing in the displayed image is different from the actual distance
because the rear view parking camera is equipped with a specific lens.
ï‚·Some optionally installed vehicle accessories may be picked up by the camera. Do not
install any optional part s that can interfere with the camera view, such as illuminating
parts or parts made of reflective material.
ï‚·It may be difficult to see the display under the following conditions, however, it does not
indicate a malfunction.
ï‚·In darkened areas.
ï‚·When the temperature around the lens is high/low.
ï‚·When the camera is wet such as on a rainy day or during periods of high humidity.
ï‚·When foreign material such as mud is stuck around the camera.
ï‚·When the camera lens reflects sunlight or headlight beams.
ï‚·Image display may be delayed if the temperature around the camera is low.
When Driving
Rear View Monitor (Maz da Connect (Type A))
4-246
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

ï‚·When foreign material such as mud is stuck around the camera.
ï‚·When the camera lens reflects sunlight or headlight beams.
ï‚·The surroundings are illuminated by vehicle lights, fluorescent lights, or LED lights
(display may flicker).
ï‚·Extremely small dark or white dots appear on the screen (dots may flicker).
ï‚·Image display may be delayed if the temperature around the camera is low.
â–¼Viewing the Display
Guide lines which indicate the width of the vehicle are display
ed on the screen as a
reference to the approximate width of the vehicle in comparison to the width of the parking
space you are about to back into.
Use this display view for parking your vehicle in a parking spa ce or garage.
a) Vehicle width guide lines
Guide lines serve as a reference to the approximate width of th e vehicle.
b) Distance guide lines These guide lines indicate the approximate distance to a point measured from the
vehicle's rear (from the end of the bumper).
The red line indicates the point about 0.5 m (19 in) from the r ear bumper.
The yellow lines indicate the points about 1.0 m (39 in) and 2. 0 m (78 in) from the rear
bumper.
â–¼ Rear View Monitor Operation
The operation of the rear view monitor when reversing the vehic
le varies depending on the
traffic, road, and vehicle conditions. The amount of steering a nd the timing also varies
depending on conditions, so conf irm the surrounding conditions directly with your eyes and
steer the vehicle in accordance with the conditions.
Be well aware of the above cautions prior to using the rear vie w monitor.
NOTE
Images displayed on the monitor from the rear view parking camera are reversed images
(mirror images).
When Driving
Rear View Monitor (Mazda Connect (Type B))
4-255
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22