heating MAZDA MODEL CX-9 2022 User Guide

“Programming HomeLink” step 3 with
the following:
NOTE
If programming a garage door opener or
gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating.
Continue to press and hold the HomeLink
button while you press and release ―
every two seconds (“cycle”) your
hand-held transmitter until the frequency
signal has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.)
Proceed with “Programming” step 4 to
complete.
▼ Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The code
will continue being transmitted for a
maximum of 20 seconds.
▼Reprogramming the HomeLink
system
To program a device to HomeLink using a
HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the
HomeLink button, proceed with
“Programming” - step 1.
▼Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons (
, ) on
the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 10 seconds.
Verify that the programming has been
erased when you re
sell the vehicle.
When Driving
Switches and Controls
4-75
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

NOTE
To program the remaining two HomeLink
buttons, go back to Step 1 of
Programming the HomeLink System and
repeat the procedure.
For questions or comments, please contact
HomeLink at www.homelink.com or
www.youtube.com/HomeLinkGentex , or
the HomeLink to ll-free hotline at
1-800-355-3515 (for calls placed outside
of the USA, Canada, and Puerto Rico,
international rates will apply and may
differ based on landline or mobile phone).
▼ Gate operator/Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission ―
which may not be long enough for
HomeLink to pick up
the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are designed
to “time-out” in the same manner.

If you live in Canada or are having
difficulties programming a gate operator
by using the programming procedures
(regardless of where you live), replace
Step 3 of Programming the HomeLink
System with the following:
NOTE
If programming a garage door opener or
gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating.
While the indicator light is flashing in
amber, press the button on the hand-held
transmitter for 2 sec onds and release it
repeatedly until the in dicator light changes
from amber to green.
Go back to Step 4 of Programming the
HomeLink System to complete the
procedure.
▼ Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device.
▼Reprogramming the HomeLink
system
To program a device to HomeLink using a
HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. DO NOT release the button.
2. After 20 seconds, the indicator light flashes in amber. After the indicator
light flashes, release the HomeLink
button.
3. Go back to Step 2 of Programming the HomeLink System to complete the
procedure.
NOTE
If the programming has not been
completed, the syst em returns to the
previous programming.
▼ Erasing Programmed HomeLink
Buttons
NOTE
All of the programmed HomeLink
buttons are reset.
Individual buttons
cannot be reset, however, individual
buttons can be reprogrammed. For
individual button reprogramming, refer
to Reprogramming the HomeLink
System (page 4-78).
When Driving
Switches and Controls
4-78
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

parking brake is applied, the EPB switch
indicator light turns on.
Indicator light
WARNING
Do not drive the vehicle with the parking
brake applied:
If the vehicle is driven with the parking
brake applied, the brake parts may
generate heat and the brake system may
not operate, leading to an accident.
Before driving, release the parking brake
and verify that the brake system warning
light is turned off.
NOTE
The parking brake cannot be applied or
released while the vehicle battery is
dead.
If the EPB is repeatedly applied and
released it may stop operating to
prevent overheating of the motor. If this
occurs, wait approx. 1 minute before
operating the EPB switch again.
An operation sound occurs when
applying or releasing the parking brake,
however, this does not indicate a
malfunction.
If the EPB is not used for long periods,
an automatic inspection of the system is
performed while the vehicle is parked.
An operation sound can be heard,
however, this does not indicate a
problem.
When the parking brake is applied and
the ignition is switched OFF, an
operation sound can be heard, however,
this does not indicate a problem.
The brake pedal may move while the
parking brake is being applied or
released, however, this does not indicate
a problem.
If the EPB switch is continually pulled
while driving the vehicle, the parking
brake will be applied and the EPB
warning beep will be activated. When
the switch is released, the parking brake
is released and the beep stops.
If the parking brake is applied with the
ignition switched off or in ACC, the
brake system warning light in the
instrument cluster and the indicator
light in the switch may turn on for 15
seconds.
When running the vehicle through an
automatic car wash, it may be necessary
to switch the ignition off with the
parking brake released depending on
the type of automatic car wash.
When applying the parking brake
The parking brake can be applied
regardless of the igni tion switch position.
Securely depress the brake pedal and pull
up the EPB switch.
The parking brake is applied and the brake
system warning light and the EPB switch
indicator light turn on.
When Driving
Brake
4-81
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

i-ACTIV AWD Operation*
AWD provides excellent drivability on
snow-covered and ice-packed roads, sand
and mud, as well as on steep slopes and
other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Contact an Authorized Mazda Dealer and
Have Vehicle Inspected on page 7-31.
WARNING
Never spin a wheel that is off the ground:
Spinning a wheel that is off the ground as a
result of the vehicle being stuck or in a
ditch is dangerous. The drive assembly
could be seriously damaged which could
lead to an accident or could even lead to
overheating, oil leakage, and a fire.
▼ AWD Driving
WARNING
Avoid sharp turns, excessive speed and
abrupt maneuvers when driving this
vehicle:
Sharp turns, excessive speed and abrupt
maneuvering of this vehicle is dangerous
as it could result in the increased risk of loss
of vehicle control, vehicle roll-over,
personal injury or death.
This vehicle has a higher center of gravity.
Vehicles with a higher center of gravity
such as utility and AWD vehicles handle
differently
than vehicles with a lower center
of gravity.
Utility and AWD vehicles are not designed
for cornering at high speeds any more than
low profile sports cars are designed to
perform satisfactorily under off-road
conditions. In addition, utility vehicles have
a significantly higher rollover rate than
other types of vehicles.
Drive carefully when the vehicle is loaded
by lowering vehicle speed and applying the
brakes earlier:
Abrupt maneuvering and sudden braking
when driving a loaded vehicle is dangerous
as the driving behavior of a vehicle with a
high center of gravity is different when it is
loaded compared to when it is not, and
could result in the loss of vehicle control
and an accident.
▼ Tires and Tire Chains
The condition of the ti
res plays a large role
in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
Tires
When replacing tires, always replace all
front and rear tires at the same time.
All tires must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tires.
Do not mix tread-worn tires with normal
tires.
Inspect tire inflation pressures at the
specified periods adjust to the specified
pressures.
NOTE
Check the tire inflation pressure label
attached to driver's door frame for the
correct tire inflation pressure.
When Driving
i-ACTIV AWD
*Some models.4-99
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
Parking in an Emergency................. 7-2 Parking in an Emergency..............7-2
Flat Tire.............................................. 7-3 Spare Tire and Tool Storage......... 7-3
Changing a Flat Tire..................... 7-9
Battery Runs Out............................ 7-19 Jump-Starting............................. 7-19
Emergency Starting.........................7-22 Starting a Flooded Engine.......... 7-22
Push-Starting.............................. 7-22
Overheating......................................7-23 Overheating................................ 7-23
Emergency Towing.......................... 7-25 Towing Description.................... 7-25
Towing Hooks (Mexico ).............7-26
Warning/Indicator Lights and
Warning Sounds.............................. 7-28
If a Warning Light Turns On or
Flashes........................................ 7-28
Message Indicated on
Display........................................7-41
Message Indicated in Multi-
information Display.................... 7-43
Warning Sound is Activated....... 7-45
When Liftgate Cannot be
Opened..............................................7-50 When Liftgate Cannot be
Opened........................................7-50
Active Driving Display Does Not
Operate
*........................................... 7-51
If the Active Driving Display Does
Not Operate................................ 7-51
*Some models.7-1
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

Overheating
If the temperature gauge indicates
overheating or the high engine coolant
temperature warning light turns on, the
vehicle loses power, or you hear a loud
knocking or pinging noise, the engine is
probably too hot.
WARNING
Pull over to a safe location, then switch
the ignition off and make sure the fan is
not running before attempting to work
near the cooling fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if the
engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and radiator
are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot out
under pressure and cause serious injury.
Open the hood ONLY after steam is no
longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the temperature gauge indicates
overheating or the high engine coolant
temperature warning light turns on:

1. Drive safely to the side of the road and
park off the right-of-way.
2. Shift into park (P).
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is escaping from the engine
compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.

If neither coolant nor steam is
escaping:
Open the hood and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
6. Make sure the cooling fan is operating, then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If Trouble Arises
Overheating
7-23
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

If it is low, look for coolant leaks from
the radiator and hoses.

If you find a leak or other damage, or if
coolant is still leaking:
Stop the engine and call an Authorized
Mazda Dealer.
Cooling system cap
Coolant reservoir
Cooling fan
If you find no problems, the engine is
cool, and no leaks are obvious:
Carefully add coolant as required (page
6-22).
CAUTION
If the engine continues to overheat or
frequently overheats, have the cooling
system inspected. The engine could be
seriously damaged unless repairs are
made. Consult an Authorized Mazda
Dealer.
If Trouble Arises
Overheating
7-24
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

SignalWarning
Charging System Warn‐
ing Indication/Warning Light If the warning light illuminates while driving, it indicates a
malfunction of the alter‐
nator or of the charging system.
Drive to the side of the road and park off the right-of-way. Co nsult an Authorized
Mazda Dealer.
CAUTION
Do not continue driving when the charging system warning light is illuminated be‐
cause the engine could stop unexpectedly.
Engine Oil Warning Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is
low. Otherwise, it could result in extensive
engine damage.
If the light illuminates or the w arning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way o n level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain b ack into the oil pan.
3. Inspect the engine oil level (p age 6-21). If it's low, add the appropriate amount of
engine oil while being careful not to overfill.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.

If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an Authorized Mazda
Dealer.
(Red)
High Engine Coolant
Temperature Warning Indication/Warning Light The light flashes when the engine
coolant temperature is extremely high, and illumi‐
nates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can find a safe pl ace to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place immedi‐
ately and stop the engine.
Refer to Overheating on page 7-23.
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light illumi‐
nated. Otherwise, it could resu lt in damage to the engine.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-30
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

Index
Appendix..................................... 5-45
Appendix (Mazda Connect (Type
A))................................................5-25
Appendix (Mazda Connect (Type
B))................................................ 5-45
Connected Service....................... 5-53
Mazda Connect Basic
Operations....................................5-37
Mazda Connect Basic Operations
(Mazda Connect (Type A))..........5-17
Mazda Connect Basic Operations
(Mazda Connect (Type B)).......... 5-37
Mazda Connect (Mazda Connect
(Type A))..................................... 5-14
Mazda Radar Cruise Control with Stop &
Go function (MRCC with Stop & Go
function).......................................... 4-131 Close proximity warning........... 4-135
Cruise control function.............. 4-143
Display indication......................4-133
Setting the system..................... 4-136
Stop hold control....................... 4-142
Message Indicated in Multi-information
Display.............................................. 7-43
Message Indicated on Display.......... 7-41
Meters................................................ 4-11
Mirrors Outside mirrors..... ....................... 3-32
Rearview mirror.......................... 3-34
Mirror Defogger......... ....................... 4-70
Moonroof...........................................3-40
Multi-information Display (Type
A).......................................................4-13
Multi-information Display (Type
B)....................................................... 4-30
O
Off-Road Traction Assist
Off-Road Traction Assist indicator
light.............................................. 4-95
Off-Road Traction Assist
switch........................................... 4-96
Outside Mirrors......... ........................ 3-32
Overhead Console............................. 5-69
Overhead Lights................................ 5-56
Overheating....................................... 7-23
Overloading....................................... 3-52
Owner Maintenance
Closing the hood...... ................... 6-17
Engine compartment overview.... 6-19
Key battery replacemen t..............6-32
Opening the hood........................ 6-17
Owner maintenance
precautions................................... 6-15
P
Parking Sensor System (Mazda Connect
(Type A))......................................... 4-260 Sensor detection range.............. 4-262
Parking Sensor System (Mazda Connect
(Type B))......................................... 4-270
Power Liftgate................................... 3-20
Power Liftgate Warning Beep........... 7-47
Power Steering................................ 4-101
Power Steering Warning Buzzer....... 7-48
Power Windows............. ................... 3-37
R
Radar Sensors (Rear)...................... 4-231
Radar Sensor (Front).......................4-228
Rearview Mirror........ ........................3-34
Rear Coat Hooks....... ........................ 5-74
Rear Cross Traffic Alert (RCTA).... 4-127
Rear Door Child Safet y Locks.......... 3-18
Rear View Monitor
Picture quality adjus tment......... 4-250
Rear View Monitor (Mazda Connect
(Type A))......................................... 4-244
Displayable range on the
screen......................................... 4-246
10-7
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22

Index
Smart City Brake Support [Forward]
(SCBS F)......................................... 4-160Stopping the Smart City Brake
Support [Forward] (SCBS F) system
operation.................................... 4-162
Smart City Brake Support [Reverse]
(SCBS R)........................................ 4-163
Stopping the Smart City Brake
Support [Reverse] (SCBS R) system
operation.................................... 4-166
Spare Tire............................................ 7-6
Specifications...................................... 9-4
SRS Air Bags Front passenger occupant
classification system.................... 2-85
How the SRS air bags work........ 2-78
Limitations to SRS air bag.......... 2-83
Monitoring................................... 2-89
SRS air bag deployment
criteria.......................................... 2-82
Supplemental restraint system
components.................................. 2-76
Starting the Engine..............................4-5
Steering Wheel Heated steering wh eel................. 2-34
Horn............................................. 4-71
Storage Box.......................................5-70
Storage Compartments ...................... 5-69
Armrest box................................. 5-71
Center console............................. 5-70
Glove compartment..................... 5-70
Luggage Compartment................ 5-72
Overhead console........................ 5-69
Rear coat hooks........................... 5-74
Shopping bag hook.... ..................5-74
Storage Box................................. 5-70
Sunshade............................................3-42
Sunshade (Rear door window).......... 5-75
Sunvisors........................................... 5-55T
Theft-Deterrent System ..................... 3-45
Third-Row Seat................................. 2-26
Three-flash Turn Signal.................... 4-65
Tires................................................... 6-34 Flat tire.......................................... 7-3
Replacing a tire........................... 6-36
Replacing a wheel....................... 6-37
Snow tires.................................... 3-50
Specifications.................................9-7
Temporary spare tire....................6-36
Tire chains................................... 3-51
Tire inflation pressure................. 6-34
Tire rotation................................. 6-35
Uniform tire quality grading system
(UTQGS)..................................... 8-23
Tire Inflation Pressure Warning
Beep...................................................7-48
Tire Information................................ 8-25
Tire Pressure Monitoring System.... 4-240
To w i n g
Hook............................................ 7-26
Recreational towing.....................3-63
Trailer towing (U.S.A. and
Canada)........................................ 3-55
Towing Description........................... 7-25
Traction Control System (TCS)........ 4-91
TCS OFF Indicator Light............ 4-92
TCS OFF Switch......................... 4-92
TCS/DSC indicator light............. 4-91
Traffic Sign Recognition System
(TSR)............................................... 4-115
Trailer Stability Control (TSC)......... 4-94
Transmitter.......................................... 3-5
Trouble
Battery runs out........................... 7-19
Emergency starting...................... 7-22
Emergency towing....................... 7-25
Flat tire.......................................... 7-3
Overheating................................. 7-23
10-9
CX-9_8KH5-EA-21K_Edition2_old 2021-9-16 14:11:22