belt MAZDA MODEL MILLENIA 2002 (in English) Owner's Manual

2-24
Essential Safety Equipment
SRS Air Bags
Form No. 8Q47-EA-01F
Air Bags without Seat Belts:
Depending only on the air bags for protection during an accident is dangerous.
Alone, air bags may not prevent serious injuries. The appropriate air bags can be
expected to inflate only during a frontal, side or near-frontal collision of at least
moderate force. Vehicle occupants should always wear seat belts.
Child in the Front Seat:
Placing a child, 12 years or under, in the front seat is dangerous. The child could be
hit by a deploying air bag and be seriously injured or even killed. A sleeping child is
more likely to lean against the door and be hit by the side air bag in a moderate, right-
side collision. Whenever possible, always secure a child 12 years and under on the
rear seat with an appropriate child-restraint system for the child's age and size.
Rear-Facing Child-Restraint System:
Rear-facing child-restraint systems on the front seat are particularly dangerous.
The child-restraint system can be hit by a deploying air bag and moved violently
backward resulting in serious injury or death to the child. NEVER use a rear-facing
child-restraint system in the front seat with an air bag that could deploy.
Seating Position with Front Air Bags:
Sitting too close to the air bag storage compartments or placing hands or feet on them
is extremely dangerous. Front Air bags inflate with great force and speed. Serious
injuries could occur if someone is too close. The driver should always hold onto only
the rim of the steering wheel. The front seat passenger should keep both feet on the
floor. Front seat occupants should adjust their seats as far back as possible and
always sit upright against the seatbacks with seat belts worn properly.
WARNING
Deploying air bag
J76Y.book Page 24 Wednesday, March 27, 2002 5:04 PM

2-25
Essential Safety Equipment
SRS Air Bags
Form No. 8Q47-EA-01F
Seating Position with Side Air Bags:
Sitting too close to the side air bag storage compartments or placing hands on them is
extremely dangerous. A side air bag inflates with great force and speed directly out of
the outboard shoulder of the front seat and expands along the front door on the side
the car is hit.
Serious injury could occur if someone is sitting too close to the door or leaning
against a window in the front seats or if rear seat occupants grab the sides of the front
seatbacks. Furthermore, sleeping up against the door or hanging out the driver's-side
window while driving could block the side air bag and eliminate the advantages of
supplemental protection. Give the side airbags room to work by sitting in the center of
the seat while the vehicle is moving with seat belts worn properly.
Front Air Bag Storage Areas:
Attaching an object to a front air bag storage area or placing something in front of it
is dangerous. In an accident, the object could interfere with front air bag inflation
and injure the occupants.
Always keep the front air bag storage areas free of objects.
Side Air Bag Storage Areas:
Attaching things to the seat in such a way as to cover the outboard side of the seat in
any way is dangerous. In an accident the object could interfere with the side air bag,
which inflates from the outboard side of the front seats, impeding the added
protection of the side air bag system or redirecting the air bag in a way that is
dangerous. Furthermore, the bag could be cut open spewing exhaust.
Do not hang net bags, map pouches or back pads with side straps on the front seats.
Always keep the side air bag storage areas in your front seats free to deploy in the
event of a side collision.
Hot Air Bag Inflators:
Hot air bag inflators are dangerous. Immediately after inflation, the inflators in the
steering wheel, dashboard or the seatbacks are very hot. You could get burned. Don't
touch the internal components of the air bag storage areas after the bags have
inflated.
Installation of Front-End Equipment:
Installation of front-end equipment, such as frontal protection bar (kangaroo bar,
bull bar, push bar, etc.), snowplow, or winches, is dangerous. The air bag crash sensor
system could be affected. This could cause air bags to inflate unexpectedly, or it could
prevent the air bags from inflating during an accident. Front occupants could be
seriously injured. Never install any front-end equipment to your vehicle.
WARNING
J76Y.book Page 25 Wednesday, March 27, 2002 5:04 PM

4-5
Before Driving Your Mazda
Form No. 8Q47-EA-01F
Before Starting the Engine
•Be sure the windows, outside mirror(s),
and outside lights are clean.
•Inspect inflation pressures and
condition of tires.
•Look under the vehicle for any sign of
a leak.
•If you plan to back up, make sure
nothing will be in your way.•Are all doors closed and locked?
•Are the inside and outside mirrors
adjusted?
•Is everyone’s seat belt fastened?
•Do all the lights work?
•Check all gauges.
•Check all warning lights when the
ignition switch is turned to the ON
position.
•Release the parking brake and make
sure the brake warning light goes off.
Always be thoroughly familiar with your
Mazda.
Before Getting In
NOTE
Engine oil, engine coolant, brake fluid,
washer fluid, and other fluid levels
should be inspected daily, weekly, or at
refueling, depending on the fluid. See
Maintenance, Section 8.
After Getting In
J76Y.book Page 5 Wednesday, March 27, 2002 5:04 PM

5-3
Driving Your Mazda
Starting and Driving
Form No. 8Q47-EA-01F
1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
5. Turn the ignition switch to the START
position and hold (up to 10 seconds at a
time) until the engine starts.
6. After starting the engine, let it idle for
about 10 seconds.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the shift
lever is not
in P or N.
Don’t try the starter for more than 10
seconds at a time. If the engine stalls or
fails to start, wait 10 seconds before
trying again. Otherwise, you may
damage the starter and drain the
battery.
CAUTION
NOTE
•In extremely cold weather, below
−18
°C (0
°F), or after the vehicle has
stood idle several days, let the
engine warm up without operating
the accelerator.
•Whether cold or warm, the engine
should be started without use of the
accelerator.
J76Y.book Page 3 Wednesday, March 27, 2002 5:04 PM

5-23
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q47-EA-01F
Seat Belt Warning Light 5-28
Door-Ajar Warning Light 5-28
Low Washer Fluid Level Warning Light 5-28
Headlight High-Beam Indicator Light 5-28
Hold Indicator Light 5-28
TCS Indicator Light 5-29
TCS OFF Indicator Light 5-29
Cruise Set Indicator Light 5-29
Light-On Indicator Light 5-29 Signal Warning/Indicator Lights Page
J76Y.book Page 23 Wednesday, March 27, 2002 5:04 PM

5-28
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q47-EA-01F

Low Fuel Warning Light
This warning light in the fuel gauge
signals that the fuel tank will soon be
empty.
Get fuel as soon as possible.

Seat Belt Warning Light
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.

Door-Ajar Warning Light
This warning light comes on when any
door isn’t securely closed.

Low Washer Fluid Level
Wa r n i n g L i g h t
This warning light reveals that little
windshield washer fluid remains. Add
fluid (page 8-19).

Headlight High-Beam Indicator
Light
This light indicates one of two things:
•The high-beam headlights are on.
•The turn signal lever is in the flash-to-
pass position.

HOLD Indicator Light
This light comes on when the hold mode
is selected.
Low fuel warning light
J76Y.book Page 28 Wednesday, March 27, 2002 5:04 PM

5-30
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q47-EA-01F

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.
Beeps
J76Y.book Page 30 Wednesday, March 27, 2002 5:04 PM

7-13
In Case of an Emergency
Emergency Starting
Form No. 8Q47-EA-01F
1. Make sure the booster battery is 12 V
and that its negative terminal is
grounded.
2. If the booster battery is in another
vehicle, don’t allow the vehicles to
touch. Turn off the engine of the
vehicle with the booster battery and all
unnecessary electrical loads in both
vehicles.
3. Connect the jumper cables in the exact
sequence as in the illustration.
•Connect one end of a cable to the
positive terminal on the discharged
battery (1).
•Attach the other end to the positive
terminal on the booster battery (2).
•Connect one end of the other cable
to the negative terminal of the
booster battery (3).
•Connect the other end to a solid,
stationary, exposed metallic point
(for example, the engine hanger)
away from the discharged battery
(4).4. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle.
5. When finished, carefully disconnect
the cables in the reverse order
described in Step 3.
Jumper
cables
Booster battery
Connect cables in
numerical order and
disconnect in reverse order.
Discharged
battery
Connecting to Negative Terminal:
Connecting the end of the second
cable to the negative ( ) terminal of
the discharged battery is dangerous.
A spark could cause the gas around
the battery to explode and injure
someone. Connect the cable to a point
away from the battery.
Connecting Jumper Cable to a
Moving Part:
Connecting a jumper cable near or to
a moving parts (cooling fans, belts) is
dangerous. The cable could get
caught when the engine starts and
cause serious injury. Never connect a
jumper cable to or near any part that
moves.
WARNING
J76Y.book Page 13 Wednesday, March 27, 2002 5:04 PM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q47-EA-01F

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 6 12182430364248
×1000 Km 12 24 36 48 60 72 84 96
(×1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60)
Engine valve clearance Miller Cycle
Engine V6 DOHCI
Drive belts (tension)2.5 liter V6 DOHCII
Miller Cycle
Engine V6 DOHCReplace every 168,000km (105,000miles)
Engine timing belt2.5 liter V6 DOHCInspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Miller Cycle
Engine V6 DOHCReplace every 96,000km (60,000miles)
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000km (45,000miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Idle speedII
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Air filterRR
Spark plugs2.5 liter V6 DOHCReplace every 48,000km (30,000miles)
Miller Cycle
Engine V6 DOHCReplace every 96,000km (60,000miles)
Brake lines, hoses and connectionsII
Disc brakesII
Automatic transaxle fluid levelII
Steering operation and linkagesII
Front and rear suspension ball jointsII
Driveshaft dust bootsII
Bolts and nuts on chassis and bodyII
Exhaust system heat shieldsII
Body inspection (paint, corrosion)IIIIIIII
Compressor operationIIII
Cabin air-filter (if installed)Replace once a year or every 20,000km (12,000miles)
J76Y.book Page 4 Wednesday, March 27, 2002 5:04 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q47-EA-01F

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
:Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*2: If the vehicle is operated in cold districts { below -18 degrees C (0 degrees F) }, replace the timing belt at
96,000km (60,000miles).
Maintenance
Interval
Maintenance
ItemNumber of months or kilometers (miles), whichever comes first
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearanceMiller Cycle Engine
V6 DOHCI
Drive belts (tension)2.5 liter V6 DOHCII
Miller Cycle Engine
V6 DOHCReplace every 168,000km (105,000miles)
Engine timing belt2.5 liter V6 DOHC
*2Inspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Miller Cycle Engine
V6 DOHCReplace every 96,000km (60,000miles)
Engine oilPuerto RicoReplace every 5,000km (3,000miles) or 3 months
othersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000km (45,000 miles) or 36 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant levelIIIIIIIIIIII
Idle speedI I
Fuel lines and hoses
*1I I
Hoses and tubes for emission*1I
Air filter
I *1R
I *1R
Spark plugs 2.5 liter V6 DOHCReplace every 48,000km (30,000miles)
Miller Cycle Engine
V6 DOHCReplace every 96,000km (60,000miles)
Function of all lightsIIIIIIIIIIII
Brake lines, hoses and connectionsII
Brake fluid levelIIIIIIIIIIII
Disc brakesIIII
Automatic transaxle fluid levelII
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation and linkagesII
J76Y.book Page 5 Wednesday, March 27, 2002 5:04 PM