coolant level MAZDA MODEL MPV 2002 Owners Manual (in English)

4-6
Before Driving Your Mazda
Form No. 8Q44-EA-01K
Before Starting the Engine
•Be sure the windows, outside mirror(s),
and outside lights are clean.
•Inspect inflation pressures and
condition of tires.
•Look under the vehicle for any sign of
a leak.
•If you plan to back up, make sure
nothing will be in your way.•Are all doors closed and locked?
•Are the inside and outside mirrors
adjusted?
•Is everyone’s seat belt fastened?
•Do all the lights work?
•Check all gauges.
•Check all warning lights when the
ignition switch is turned to the ON
position.
•Release the parking brake and make
sure the parking brake warning light
goes off.
Always be thoroughly familiar with your
Mazda.
Before Getting In
NOTE
Engine oil, engine coolant, brake fluid,
washer fluid, and other fluid levels
should be inspected daily, weekly, or at
refueling, depending on the fluid. See
Maintenance, Section 8.
After Getting In
J16L_EA.book Page 6 Friday, February 22, 2002 11:34 AM

7-15
In Case of an Emergency
Form No. 8Q44-EA-01K
Overheating
If the temperature gauge indicates
overheating, you experience power loss,
or you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Shift into park (P).
Apply the parking brake.
3. Turn off the air conditioner.4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don’t go near the front of the vehicle.
Stop the engine. Then turn the ignition
switch to the ON position without
starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools. If this doesn’t lower the
temperature, stop the engine and let it
cool.
5. Check the coolant level.
If it’s low, look for leaks in the radiator
hoses and connections, heater hoses
and connections, radiator, and water
pump.
If you find a leak or other damage, or if
coolant is still leaking, stop the engine
and call an Authorized Mazda Dealer.
If you find no problems, the engine is
cool, and no leaks are obvious, carefully
add coolant as required (page 8-11).
Overheating
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
F
L
Cooling
system cap
Coolant reservoir
J16L_EA.book Page 15 Friday, February 22, 2002 11:34 AM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q44-EA-01K

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air cleaner elements cannot be cleaned using the air-blow method.)
R
: Replace L
: Lubricate
*
1According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*
2If the vehicle is operated under any of the following conditions, change the spark plugs every 96,000
km(60,000 miles) or shorter.
a) Repeated short-distance driving
b) Extended periods of idling or low-speed operation
c) Driving for long periods in cold temperatures or extremely humid climates
d) Towing a trailer Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine oilPuerto RicoReplace every 5,000 km (3,000 miles) or 3 months
OthersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Drive belts II
PCV valve*
1I
Hoses and tubes for emission (Puerto Rico)I
Spark plugs (Platinum
tipped type)USAReplace every 96,000 km (60,000 miles)
Others*
2Replace every 160,000 km (100,000 miles)
Air filterPuerto RicoI R I R
OthersIR I
Fuel lines and hoses*
1I I
Cooling systemII
Engine coolantReplace at first 72,000 km (45,000 miles) or 36 months ;
after that, every 48,000 km (30,000 miles) or 24 months
Engine coolant levelIIIIIIIIIIII
Function of all lightsIIIIIIIIIIII
Brake lines, hoses and connectionsII
Brake fluidRR
Brake fluid level IIIIIIIIIIII
Disc brakesIIII
Drum brakes I I
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation and linkagesII
Power steering fluid levelIIIIIIIIIIII
Front suspension ball jointsII
Driveshaft dust bootsII
Bolts and nuts on chassis and bodyIIII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLLLLLL
Washer fluid levelIIIIIIIIIIII
Refrigerant amountIIII
Compressor operationIIII
Cabin air filter (if equipped)Replace once a year or every 20,000 km (12,000 miles)
J16L_EA.book Page 5 Friday, February 22, 2002 11:34 AM

8-6
Maintenance and Care
Form No. 8Q44-EA-01K
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
•Brake fluid level (page 8-13)
•Engine coolant level (page 8-11)
•Engine oil level (page 8-9)
•Washer fluid level (page 8-16)

At Least Monthly
•Tire inflation pressures (page 8-23)

At Least Twice a Year (For Example, Every Spring and Fall)
•Automatic transaxle fluid level (page 8-15)
•Power steering fluid level (page 8-14)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
•Air filter (page 8-17)
•Engine coolant (page 8-11)
•Engine oil (page 8-10)
Owner Maintenance Schedule
J16L_EA.book Page 6 Friday, February 22, 2002 11:34 AM

8-8
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
Engine Compartment Overview
Automatic transaxle fluid-level dipstick
Cooling system cap
Engine coolant reservoir
Power steering
fluid reservoir
Windshield washer
fluid reservoir
Engine oil dipstick Engine oil-filler cap
Engine oil filterBatteryFuse blockAir filter Brake fluid reservoir
J16L_EA.book Page 8 Friday, February 22, 2002 11:34 AM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
Check the oil level and fill to the MAX
mark if necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)
Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.

Inspecting Coolant Level
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of the
winter season—and before traveling
where temperatures may drop below
freezing.
Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the F and L marks
on the coolant reservoir when the engine
is cool.
NOTE
•The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•Use only specified engine oil (page
10-4).
Engine Coolant
Hot Engine:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Don’t
inspect the coolant system or add
coolant when the engine is hot.
WARNING
J16L_EA.book Page 11 Friday, February 22, 2002 11:34 AM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
If it’s at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
Do not overfill.
If new coolant is required frequently,
consult an Authorized Mazda Dealer.

Changing Coolant (Without Rear
Heater)
Change coolant according to Scheduled
Maintenance (page 8-3).For mixture percentage:
To change coolant
1. Remove the cooling system cap. Radiator coolant will damage paint.
Rinse it off quickly.
•Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant’s effectiveness.
•Don’t add only water. Always add a
proper coolant mixture.
•The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
•DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
•Don’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
CAUTION
CAUTION
ProtectionVo l u m e
Antifreeze
solutionWa t e r
Above -16°C (3°F) 35% 65%
Above -26°C (-15°F) 45 55
Above -40°C (-40°F) 55 45
Removing the Cooling System Cap:
Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you’re sure all the pressure is
gone, press down on the cap—still
using a cloth—turn the cap, and
remove it.
WARNING
F
L
Tighten Loosen
TightenLoosen
J16L_EA.book Page 12 Friday, February 22, 2002 11:34 AM

8-13
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
2. Only when the engine is cool, remove
the radiator drain plug and drain the
coolant into a suitable container.
3. Flush out the system with running
water.
4. Drain the system completely. Insert
and tighten the plug. Add as much
ethylene-glycol-based coolant and
water as necessary to provide freezing
and corrosion protection.
5. In extremely cold climates, add the
amount recommended in the coolant
manufacturer’s instructions.
6. Run the engine at idle with the cooling
system cap off. Slowly add additional
coolant if necessary.
7. At this point, wait until the engine
reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
8. Install the cooling system cap. Inspect
all connections for leaks. Inspect the
level in the coolant reservoir one more
time.

Changing Coolant (With Rear
Heater)
Have an Authorized Mazda Dealer change
the coolant according to the Scheduled
Maintenance (page 8-3).

Inspecting Brake Fluid Level
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake linings. If it
is excessively low, have the brake system
inspected by an Authorized Mazda
Dealer.
Brake Fluid
J16L_EA.book Page 13 Friday, February 22, 2002 11:34 AM

10-5
Specifications
Form No. 8Q44-EA-01K

Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
*With license plate holder

We i g h t s

Air Conditioner
ItemUnit
L US qt Imp qt
Engine oilWith oil filter replacement 5.2 5.5 4.6
Without oil filter replacement 4.7 5.0 4.1
CoolantWith rear heater 12.4 13.1 11.0
Without rear heater 10.6 11.2 9.3
Automatic transaxle fluid 9.7 10.3 8.5
Washer fluidWith 4-Seasons package 5.5 5.8 4.8
Without 4-Seasons package 2.2 2.3 1.9
Fuel tank 75 19.8 (US gal) 16.5 (Imp gal)
Item mm (in)
Overall lengthWithout GFX Package 4,769 (187.8), 4,794 (188.7)*
With GFX Package 4,786 (188.4), 4,810 (189.4)*
Overall width 1,830 (72.1)
Overall height 1,745 (68.7)
Front tread 1,540 (60.6)
Rear tread 1,545 (60.8)
Wheelbase 2,840 (111.8)
Item Weight
GVWR (Gross Vehicle Weight Rating) 2,372 kg (5,229 lb)
GAWR (Gross Axle Weight Rating)Front 1,180 kg (2,601 lb)
Rear 1,214 kg (2,676 lb)
Refrigerant complies with SAE J639 Maximum operating charge
R-134aFront air-conditioner 0.65 kg (22.9 oz)
Front and rear air-conditioner 0.85 kg (30.0 oz)
J16L_EA.book Page 5 Friday, February 22, 2002 11:34 AM