check engine MAZDA MODEL MPV 2003 (in English) User Guide

5-23
Driving Your Mazda
Form No. 8R21-EA-02G
Warning/Indicator Lights and Beeps
Warning/Indicator Lights
Signal Warning/Indicator Lights Page
Brake System Warning Light 5-25
Charging System Warning Light 5-26
Engine Oil Pressure Warning Light 5-26
Check Engine Light 5-27
ABS Warning Light 5-27
Air Bag/Front Seat Belt Pretensioner System Warning Light 5-28
Low Fuel Warning Light 5-28
Warning/Indicator lights will appear in any of the highlighted areas
J16L_8R21-EA-02G.book Page 23 Saturday, June 8, 2002 11:16 AM

5-25
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R21-EA-02G

Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution
system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-13).
2. After adding fluid, check the light
again.If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
Even if the light goes off, have your brake
system inspected as soon as possible.
Electronic brake force distribution
system warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may turn the brake system
warning light on.
In this case, the ABS warning light comes
on at the same time (page 5-27).
J16L_8R21-EA-02G.book Page 25 Saturday, June 8, 2002 11:16 AM

5-27
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R21-EA-02G
2. Turn off the engine and inspect the
engine oil level (page 8-9). If it’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.

Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
•The fuel tank level being very low or
approaching empty.
•The engine’s electrical system has a
problem.
•The emission control system has a
problem.
•The fuel-filler cap is missing or not
tightened securely.If the check engine light flashes
continuously, decrease your speed and
consult an Authorized Mazda Dealer as
soon as possible.

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible. Don’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J16L_8R21-EA-02G.book Page 27 Saturday, June 8, 2002 11:16 AM

6-2
Interior Comfort
Form No. 8R21-EA-02G
Climate Control System

Operating the Climate Control
System
Operate the climate control system with
the engine running.

Clearing the Air Inlet
Clear all obstructions like leaves, snow
and ice from the hood and the air inlet in
the cowling grille to improve the system
efficiency.

Foggy Windows
The windows may fog up easily in humid
weather. Use the climate control system to
defog the windows.
To help defog the windows, operate the air
conditioner to dehumidify the air.

Outside/Recirculated Air
Position
Use the outside air position in normal
conditions. The recirculated air position
can be used temporarily when driving on
dusty roads or for quick cooling of the
interior.

Parking in Direct Sunlight
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then run
the climate control system.

Not Using for a Long Period
Run the air conditioner at least once a
month to keep internal parts lubricated.

Check the Refrigerant before
Weather Gets Hot
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
efficient. Consult an Authorized Mazda
Dealer for refrigerant inspection.
The optional air conditioner is filled with
HFC134a (R134a), a refrigerant that will
not damage the ozone layer.
If the air conditioner is low on refrigerant
or has a malfunction, consult an
Authorized Mazda Dealer.

Replacement of the Cabin Air
Filter
If your vehicle is equipped with an air
filter for the air conditioner, it is necessary
to change the filter periodically as
indicated in scheduled maintenance (page
8-3). Consult an Authorized Mazda
Dealer for replacement of the cabin air
filter.
Operating Tips
J16L_8R21-EA-02G.book Page 2 Saturday, June 8, 2002 11:16 AM

7-15
In Case of an Emergency
Form No. 8R21-EA-02G
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Shift into park (P).
Apply the parking brake.
3. Turn off the air conditioner.4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don’t go near the front of the vehicle.
Stop the engine. Then turn the ignition
switch to the ON position without
starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools. If this doesn’t lower the
temperature, stop the engine and let it
cool.
5. Check the coolant level.
If it’s low, look for leaks in the radiator
hoses and connections, heater hoses
and connections, radiator, and water
pump.
If you find a leak or other damage, or if
coolant is still leaking, stop the engine
and call an Authorized Mazda Dealer.
If you find no problems, the engine is
cool, and no leaks are obvious, carefully
add coolant as required (page 8-11).
Overheating
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
F
L
Cooling
system cap
Coolant reservoir
J16L_8R21-EA-02G.book Page 15 Saturday, June 8, 2002 11:16 AM

8-10
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
5. Pull it out again and examine the level.
It’s OK between MIN and MAX.
But if it’s near or below MIN, add
enough oil to bring the level to MAX.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.Changing engine oil
1. Warm up the engine for a few minutes
and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil
into a suitable container.
3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the
MAX mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the
drain plug for leaks.
7. Turn it off and wait 5 minutes for the
oil to return to the oil pan. Don’t add engine oil over MAX. This
may cause engine damage.
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Remove oil splatter from the exhaust
manifold, the exhaust pipe and the
shield. Oil left on these areas will
smoke when the engine is running.
CAUTION
WARNING
CAUTION
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
Tighten
Loosen
Front
Drain plug
J16L_8R21-EA-02G.book Page 10 Saturday, June 8, 2002 11:16 AM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G
Check the oil level and fill to the MAX
mark if necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)
Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.

Inspecting Coolant Level
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of the
winter season—and before traveling
where temperatures may drop below
freezing.
Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.
The coolant should be at full in the
radiator and between the F and L marks
on the coolant reservoir when the engine
is cool.
NOTE
•The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•Use only specified engine oil (page
10-4).
Engine Coolant
Hot Engine:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Don’t
inspect the coolant system or add
coolant when the engine is hot.
WARNING
J16L_8R21-EA-02G.book Page 11 Saturday, June 8, 2002 11:16 AM

8-15
Maintenance and Care
Owner Maintenance
Form No. 8R21-EA-02G

Inspecting Automatic Transaxle
Fluid Level
The automatic transaxle fluid level should
be inspected regularly. Measure it as
described below.
The volume of fluid changes with the
temperature. Fluid must be checked at idle
without driving at normal operating
temperature.
1. Park on a level surface and set the
parking brake firmly.
2. Idle the engine about two minutes.
Push down on the brake pedal.
3. Move the shift lever through all ranges
and set it at P.4. With the engine still idling, pull out the
dipstick, wipe it clean, and put it back.
5. Pull it out again.
The proper fluid level is marked on the
dipstick as follows.
Fluid hot scale A
When the vehicle has been driven and the
fluid is at normal operating temperature,
about 65°C (150°F), the level must be
between Full and Low.
Fluid cold scale B
When the engine has not been running
and the outside temperature is about 20°C
(70°F), the level must be between Full and
Low.
Automatic Transaxle Fluid
(ATF)
•Low fluid level causes transaxle
slippage. Overfilling can cause
foaming, loss of fluid, and transaxle
malfunction.
•Use specified fluid (page 10-4). A
nonspecified fluid could result in
transaxle malfunction and failure.
CAUTION
Sudden Vehicle Movement:
Shifting the shift lever without first
depressing the brake pedal is
dangerous. The vehicle could move
suddenly and cause an accident.
Make sure the brake pedal is applied
before shifting the shift lever.
WARNING
A
B
J16L_8R21-EA-02G.book Page 15 Saturday, June 8, 2002 11:16 AM

10-5
Specifications
Form No. 8R21-EA-02G

Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
*1With license plate holder*217 inch wheel vehicle

We i g h t s

Air Conditioner
ItemUnit
L US qt Imp qt
Engine oilWith oil filter replacement 5.2 5.5 4.6
Without oil filter replacement 4.7 5.0 4.1
CoolantWith rear heater 12.0 12.7 10.6
Without rear heater 10.2 10.8 9.3
Automatic transaxle fluid 9.7 10.3 8.5
Washer fluidWith 4-Seasons package 5.5 5.8 4.8
Without 4-Seasons package 2.2 2.3 1.9
Fuel tank 75 19.8 (US gal) 16.5 (Imp gal)
Item Model
Overall lengthWithout GFX Package
4,769 mm (187.8 in), 4,794 mm (188.7 in)
*1
With GFX Package
4,786 mm (188.4 in), 4,810 mm (189.4 in)*1
Overall width 1,830 mm (72.1 in)
Overall height
1,745 mm (68.7 in), 1,755 mm (69.1 in)*2
Front tread 1,540 mm (60.6 in)
Rear tread 1,545 mm (60.8 in)
Wheelbase 2,840 mm (111.8 in)
Item Weight
GVWR (Gross Vehicle Weight Rating) 2,372 kg (5,229 lb)
GAWR (Gross Axle Weight Rating)Front 1,180 kg (2,601 lb)
Rear 1,214 kg (2,676 lb)
Refrigerant complies with SAE J639 Maximum operating charge
HFC134a (R-134a)Front air-conditioner 0.65 kg (22.9 oz)
Front and rear air-conditioner 0.85 kg (30.0 oz)
J16L_8R21-EA-02G.book Page 5 Saturday, June 8, 2002 11:16 AM

11-6
Index
Form No. 8R21-EA-02G
T
Tachometer ...................................... 5-21
Temporary Spare Tire
...................... 8-25
Theft-Deterrent System
................... 3-29
Third-row seat
.................................. 2-17
Tiedown
Hook
......................................... 7-21
Tires
Flat tire
........................................ 7-3
Inflation pressure
...................... 8-23
Replacement
............................. 8-25
Rotation
.................................... 8-24
Snow tires
................................... 4-9
Spare tire and tool storage
.......... 7-3
Specifications
........................... 10-6
Tire chains
................................ 4-10
Uniform tire quality grading
system (UTQGS)
...................... 9-13
Tool
.................................................... 7-3
Towing
Description
............................... 7-20
Emergency towing
.................... 7-20
Recreational towing
.................. 7-21
Trailer towing
........................... 4-12
Traction Control System (TCS)
....... 5-16
TCS indicator light
................... 5-17
TCS OFF indicator light
........... 5-17
TCS OFF switch
....................... 5-17
Trailer Towing
................................. 4-12
Trip Meter
........................................ 5-20
Turn and Lane-Change Signals
....... 5-33
U
Under Seat Tray ............................... 6-49
V
Vanity Mirrors .................................. 6-41
Vehicle Information Labels
............. 10-2
W
Warning Lights ................................ 5-23
ABS
........................................... 5-27
Air bag system
.......................... 5-28
Brake system
............................. 5-25
Charging system
....................... 5-26
Check engine
............................. 5-27
Door-ajar
................................... 5-29
Engine oil pressure
.................... 5-26
Front seat belt pretensioner
system
....................................... 5-28
Immobilizer system
................... 5-29
Low fuel
.................................... 5-28
Seat belt
..................................... 5-28
Warranty
............................................. 9-8
Washer Fluid
.................................... 8-16
Weights
............................................ 10-5
Wheel Replacement
......................... 8-26
Windows
Power windows
......................... 3-19
Rear quarter windows
............... 3-22
Windshield Washer
.......................... 5-35
Windshield Wipers
........................... 5-35
Blades replacement
................... 8-18
Winter Driving
................................... 4-9
J16L_8R21-EA-02G.book Page 6 Saturday, June 8, 2002 11:16 AM