start stop button MAZDA MODEL MPV 2003 Owners Manual (in English)

5-5
Driving Your Mazda
Starting and Driving
Form No. 8R21-EA-02G

Parking Brake
Setting the parking brake
Depress the brake pedal, then pull the
brake handle fully upward.
Releasing the parking brake
Depress the brake pedal, then pull the
handle up and press the button. Lower the
handle to the release position while
holding in the button.

Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution
system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-13).
2. After adding fluid, check the light
again. Driving with the parking brake on will
cause excessive wear of the brake
linings or pads.
CAUTION
J16L_8R21-EA-02G.book Page 5 Saturday, June 8, 2002 11:16 AM

5-11
Driving Your Mazda
Starting and Driving
Form No. 8R21-EA-02G

Overdrive
Overdrive operation
In D, the transaxle automatically shifts to
overdrive, which improves fuel economy
and reduces noise.
To allow engine braking when going
down a steep grade, make sure the
overdrive button is in the off position.
And for a smoother ride with less shifting,
don’t use it when:
•Going up a steep grade.
•Driving in stop-and-go traffic.
•Pulling heavy loads.
To turn off the overdrive, push the
button.
The transaxle will then shift through a 4-
gear sequence in D.
Shift patterns without overdrive:
D = 1st, 2nd, 3rd, 4th
3 = 2nd, 3rd
2 = 2nd
To turn it on, push the button again.
Shift patterns with overdrive:
D = 1st, 2nd, 3rd, 4th, 5th
3 = 2nd, 3rd
2 = 2ndO/D OFF indicator light
This light comes on when the overdrive
has been turned off.

Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or 2, depending on the load
weight and grade steepness.
3. Release all brakes while gradually
accelerating.
Overdrive button
If the overdrive-off indicator light
flashes, the transaxle has an electrical
problem. Continuing to drive your
Mazda in this condition could cause
damage to your transaxle. Consult an
Authorized Mazda Dealer as soon as
possible.
CAUTION
J16L_8R21-EA-02G.book Page 11 Saturday, June 8, 2002 11:16 AM

6-29
Interior Comfort
Au di o S ys t em
Form No. 8R21-EA-02G
* Noise reduction system manufactured
under license from Dolby Laboratories
Licensing Corporation.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button ( ) to
eject the cassette tape.
Fast-forward/Rewind
Press the fast-forward button ( ) to
fast-forward.
Press the rewind button ( ) to rewind.
To stop this operation and play the
cassette tape, press the button again.
Reversing
Press the program button ( ) to
change cassette tape-playing direction.
Automatic program control (APC)
APC is used to find the beginning of either
the next program or the one being played.
Press the APC button ( ) to the
beginning of the next selection.
Press the APC button ( ) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.
If APC detects 15 seconds of blank space
it will automatically advance the tape to
the next selection.
Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button ( ) during play.
The current selection playing will be
repeated ("RPT" will be displayed).
Press the repeat button ( ) once again
to cancel repeat play.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
NOTE
When the cassette tape ends during
fast forward or rewind, it automatically
stops and starts playing.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
NOTE
APC may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
NOTE
RPT may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
J16L_8R21-EA-02G.book Page 29 Saturday, June 8, 2002 11:16 AM