maintenance MAZDA MODEL MPV 2005 (in English) Service Manual

Black plate (287,1)
Your Mazda's headlights and fog lights
have replaceable halogen bulbs.
WARNING
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries could
be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
qReplacing Exterior Light Bulbs
Replacing a headlight bulb
1. Make sure the ignition switch is turned
off and the headlight switch is off.
2. Lift the hood and find the bulb in the
rear of the headlight unit.3. Detach the electrical connector from
the bulb by squeezing the tabs and
pulling it to the rear.
4. Pull off the sealing cover.
5. Unhook the bulb retaining spring.
6. Swing the retaining spring out and
away to free the headlight bulb.
7. Carefully remove the headlight bulb
from the socket by pulling it straight
back.
8. Replace the bulb.
9. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-31
Mazda MPV_8T50-EA-04G_Edition1 Page287
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (288,1)
NOTE
lUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
lWhen reinstalling the sealing cover,
make sure
faces up.
Replacing a fog light bulbí
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.
2. If a retaining spring is equipped, swing
it outward.
3. Disconnect the socket from the
electrical connector by pressing the tab
on the connector with your finger.4. Turn the bulb counterclockwise and
remove it. Carefully remove the fog
light bulb from its socket by pulling it
straight back.
5. Install the new bulb in the reverse order
of removal.
Front turn signal lights/Front side-
marker lights
1. Turn the screw counterclockwise and
remove it.
2. Turn the center section of the plastic
retainer counterclockwise and remove
it, then partially peel back the
mudguard.
Removal
Installation
3. Turn the socket and bulb assembly
counterclockwise and remove it.
8-32
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page288
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (289,1)
4. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse order
of removal.
Side turn signal lights
1. Slide the unit as shown in the figure to
remove it.
2. Detach the electrical connector from
the unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Parking lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights, Taillights/Rear-
side marker lights
1. Remove the bolts with a Phillips
screwdriver and remove the rear
combination component.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Taillights/Rear side-marker lights Reverse lights Rear turn signal lights Brake lights/Taillights
4. Install the new bulb in the reverse order
of removal.
High-mount brake lights
1. Remove the liftgate upper trim.
Maintenance and Care
Owner Maintenance
8-33
Mazda MPV_8T50-EA-04G_Edition1 Page289
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (290,1)
2. Push the tab as shown in the figure,
and then remove the high-mount brake
light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
NOTE
An unsecured high-mount brake light
will allow water to leak into the vehicle.
Make sure the high-mount brake light is
tightly fastened to the vehicle and if
water still leaks, consult an Authorized
Mazda Dealer.
License plate lights
1. Slide the unit as shown in the figure to
remove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
8-34
Maintenance and Care
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page290
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (291,1)
Without moonroof, with overhead
console
Edge
Without either moonroof or overhead
console
Edge
With moonroof
Edge
3. Install the new bulb in the reverse order
of removal.
Overhead light, Courtesy lights, Vanity
mirror lightsí
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light
Edge
Courtesy lights
Edge
Maintenance and Care
Owner Maintenance
8-35íSome models. Mazda MPV_8T50-EA-04G_Edition1 Page291
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (292,1)
Vanity mirror lights
Edge
3. Install the new bulb in the reverse order
of removal.
Luggage compartment light
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the luggage
compartment light as shown in the
figure, and then remove the luggage
compartment light unit.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's side
If the electrical system doesn't work, first
inspect fuses on the driver's side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.
8-36
Maintenance and Care
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page292
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (293,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-38).
Maintenance and Care
Owner Maintenance
8-37
Mazda MPV_8T50-EA-04G_Edition1 Page293
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (294,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP,
HAZARD,
ROOM,
D.LOCK and
DRL fuses
3 ABS 60AAntilock brake
system
í, For
protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30ARear heater
í,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 IG KEY2 40AA/C, P.WIND
í,
MOONROOFí
and R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuits
10 TAIL 15A Taillights
11 AC PWR 15A Inverter
12 HORN 15A Horn
13 FOG 15AFor protection of
various circuits
14 EEC 5AFor protection of
various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 HID L 20A―
18 HID R 20A―
8-38
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page294
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (295,1)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
19 IG KEY1 60AMETER,
ENGINE and
WIPER fuses
20 EGI INJ 30AFor protection of
various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120AFor protection of
all circuits
Maintenance and Care
Owner Maintenance
8-39
Mazda MPV_8T50-EA-04G_Edition1 Page295
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (296,1)
Fuse block (Driver's side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 P.WIND 30APower
windows
í, For
protection of
various circuits
2 WIPER 20AWindshield
wipers and
washer
3 SUN ROOF 15A
Moonroofí, For protec-
tion of various circuits
4 R.WIP 10ARear window
wiper and washer
5 SEAT 20AFor protection of
various circuits
6 M.DEF 10AMirror
defroster
í, For
protection of
various circuits
7 A/C 10AAir conditioner,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 DRL 10AFor protection of
various circuits
9―――
10 H/CLEAN 20AFor protection of
various circuits
11―――
12 HAZARD 10AHazard warning
flashers
13 ROOM 15AOverhead lights,
Map lights,
Luggage
compartment
light
14 AUX POWER 25A Accessory socket
15 CLOSER LH 20AFor protection of
various circuits
16 AUDIO 10AAudio system,
For protection of
various circuits
8-40
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page296
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G