belt MAZDA MODEL MX-30 EV 2022 Repair Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2022, Model line: MODEL MX-30 EV, Model: MAZDA MODEL MX-30 EV 2022Pages: 547, PDF Size: 79.35 MB
Page 424 of 547

Tires
▼Tires
For reasons of proper performance,
safety, and better energy
effi ciency,
always maintain recommended tire
in flation pressures and stay within the
recommended load limits and weight
distribution.
WARNING
Using Di fferent Tire Types:
Driving your vehicle with di fferent
types of tires is dangerous. It could
cause poor handling and poor braking;
leading to loss of control.
Except for the limited use of the
temporary spare tire, use only the
same type tires (radial, bias-belted,
bias-type) on all four wheels.
Using Wrong-Sized Tires:
Using any other tire size than what is
speci fied for the vehicle (page 9-5)
is dangerous. It could seriously a ffect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size speci fied for the
vehicle.
▼ Tire In
flation Pressure
WARNING
Always in flate the tires to the correct
pressure:
Overin flation or underinfl ation of tires
is dangerous. Adverse handling or
unexpected tire failure could result in a
serious accident.
Refer to Tires on page 9-5.
Use only a Mazda-genuine tire valve
cap:
Use of a non-genuine part is
dangerous as the correct tire air
pressure cannot be maintained if the
tire valve becomes damaged. If the
vehicle is driven under this condition,
the tire air pressure will decrease
which could result in a serious
accident. Do not use any part for the
tire valve cap that is not a
Mazda-genuine part.
Inspect all tire pressures monthly when
the tires are cold. Maintain
recommended pressures for the best
ride, handling , and minimum tire
wear.
Refer to the speci fication charts (page
9-5).
NOTE
Always check tire pressure when tires
are cold.
Warm tires normally exceed
recommended pressures. Do not
release air from warm tires to adjust
the pressure.
Underin flation can cause reduced
energy e fficiency, uneven and
accelerated tire wear, and poor
sealing of the tire bead, which will
deform the wheel and cause
separation of tire from rim.
Overin flation can produce a harsh
ride, uneven and accelerated tire
wear, and a greater possibility of
damage from road hazards.
Keep your tire pressure at the correct
levels. If one frequently needs in flating, have it inspected.
Maintenance and Care
Owner Maintenance
6-23
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 441 of 547

Interior Care
▼Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as
the audio and switches could get wet
resulting in a malfunction or vehicle
fire.
NOTE
Do not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and gasoline. Otherwise, it may
cause discoloration or stains.
Rubbing hard with a sti
ff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following, wipe it o ff
immediately using a soft cloth.
Leaving it uncleaned could cause
discoloration, stains, cracks, or peeling
of the coating , and it will make it hard
to wipe o ff later.
Beverage or fragranceGrease or oilSoiling
▼ Seat Belt Maintenance
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
2. Wipe o ff the remaining detergent
using a cloth soaked in clean water
and wrung out well.
3. Before retracting seat belts which have been pulled out for cleaning,
dry them o ff thoroughly and make
sure there is no remaining moisture
on them.
WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorized Mazda Dealer:
If a seat belt is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.
Use a mild detergent to remove
soiling from a seat belt:
If organic solvents are used for cleaning
the seat belts or they become stained
or bleached, there is the possibility of
them becoming weakened and as a
result, they may not function at their
full capacity which could cause serious
injury or death.
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will
make it
difficult to clean them later,
and it may a ffect the smooth retracting
of the seat belt.
▼ Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
▼Upholstery and Synthetic Leather
Maintenance
Fabric
1. Clean the soiled area by lightly
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
diluted with water.
Maintenance and Care
Appearance Care
6-40
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 472 of 547

depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼TCS/DSC Indication/Indicator
Light (Turns on)
If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.
▼Air Bag/Front Seat Belt
Pretensioner System Warning
Indication/Warning Light
A system malfunction is indicated if the
warning light constantly
flashes,
constantly turns on or does not turn on
at all when the power switch is
switched ON. If any of these
conditions occurs, consult an
Authorized Mazda Dealer as soon as
possible. The system may not operate
in an accident.
WARNING
Never tamper with the air bag/
pretensioner systems and always have
an Authorized Mazda Dealer perform
all servicing and repairs:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled causing
serious injury or death.
▼ Tire Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Flashing)
If there is a problem with the TPMS or
the voltage of a tire pressure sensor
decreases, the TPMS warning light
fl
ashes and a message is displayed on
the multi-information display. Have
your vehicle inspected by an
Authorized Mazda Dealer.
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or fl ashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
Do not ignore the TPMS warning light
when it is turned on or flashing:
Continuing to drive the vehicle while
ignoring the illumination/ flashing of
the TPMS warning light is dangerous
because a tire may burst which could
lead to an accident. Take appropriate
measures as soon as possible.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-27
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 474 of 547

▼i-ACTIVSENSE Warning
Indication/Warning Light*
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the center display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-21.
▼Exterior Light Warning Indication/
Warning Light
This light illuminates if there is a
malfunction in the exterior lights
(except license plate lights). Have your
vehicle inspected by an Authorized
Mazda Dealer.
CAUTION
Do not drive the vehicle while an
exterior light has a malfunction. Poor
visibility, and not being able to signal
braking and turns may cause an
accident. In addition, if the vehicle is
driven with the lights not turned on, it
may con
flict with laws and regulations
due to poor maintenance.
▼ Seat Belt Warning Indication/
Warning Light (Front seat)
The seat belt warning light turns on if
the driver or front passenger's seat is
occupied and the seat belt is not
fastened with the power switch
switched ON.
If the driver or front passenger's seat
belt is unfastened (only when the front
passenger's seat is occupied) and if the
vehicle is driven at about 20 km/h (12
mph) or faster, or about 10 km/h (6
mph) or faster for a continuous 30
seconds, with the seat belt unfastened,
the warning light
flashes for a certain
period. After a short time, the warning
light stops flashing , but remains
illuminated.
NOTE
The warning light flashes for about 6
seconds if the driver or front
passenger's seat is not fastened
when the power switch is switched
ON.
Placing heavy items on the front
passenger's seat may cause the front
passenger's seat belt warning
function to operate depending on
the weight of the item.
To allow the front passenger
occupant classi fication sensor to
function properly, do not place and
sit on an additional seat cushion on
the front passenger's seat. The
sensor may not function properly
because the additional seat cushion
could cause sensor interference.
If a small child is seated on the front
passenger's seat, the warning light
may not operate.
Action to be taken
Fasten the seat belts.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-29
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 475 of 547

▼Seat Belt Warning Light (Rear seat)
(Red)
If the rear seat belts are not fastened
while the power switch is switched
ON , the driver and the passenger are
alerted by the warning light.
The warning light operates even if there
is no passenger on the rear seat.
NOTE
If a rear seat belt is not fastened by a
certain period of time after the EV
system has been started, the warning
light turns o
ff.
Action to be taken
Fasten the seat belts.
▼ Low Washer Fluid Level Warning
Indication/Warning Light*
This warning light indicates that little
washer
fluid remains.
Action to be taken
Add washer fluid (page 6-13).
▼ Door-Ajar/Liftgate-Ajar Warning
Indication/Warning Light
The light turns on if any door/liftgate is
not closed securely.
Action to be taken
Close the door/liftgate securely.
▼ Tire Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Turns on)
If a tire pressure decreases below the
speci
fied air pressure, the TPMS
warning light turns on.
At the same time, a message and the
tire pressure of each tire are displayed
on the multi-information display
alternately. In addition, the tire (s) with
low air pressure is displayed in yellow.
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-30*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 479 of 547

Display*1*2ContentAction to be taken
Tra ffic Jam Assist Opera-
tion Canceled Drive
Safely This message is indicated when the
Tra
ffic Jam Assist (TJA) have been can-
celed other than by the driver. Have your vehicle inspected by an
Authorized Mazda Dealer.
Distance & Speed Alert
Operation Canceled
Drive Safely This message is indicated when the
Distance & Speed Alert (DSA) have
been canceled other than by the driv-
er.
Have your vehicle inspected by an
Authorized Mazda Dealer.
Cruise Control Opera-
tion Canceled. Drive
Safely This message is indicated when the
Cruise Control have been canceled
other than by the driver.
Have your vehicle inspected by an
Authorized Mazda Dealer.
Emergency Braking Acti-
vated. Depress Brake
Pedal to Hold Stop This message is indicated after the
Smart Brake Support (SBS) brakes op-
erate and when the SBS is canceled.
Depress the brake pedal.
Touch Key Fob to Push
Button Start Switch This message is indicated when the
key battery is weak (battery dead or
damaged key). Touch the key against power switch
to start the EV system.
Refer to Starting the EV System When
the Key Battery is Dead on page 4-6.
Depress Brake Pedal to
Start Vehicle This message is displayed when the
power switch is pressed without de-
pressing the brake pedal. To start the EV system, press the pow-
er switch with the brake pedal de-
pressed.
Check Shift Selector Lev-
er Position Displays in the following cases:
Selector lever is shifted to R posi-
tion while driving forward.
Selector lever is shifted to P posi-
tion while driving.
Selector lever is shifted to D posi-
tion while reversing.
Check the selector lever position.
Close Door and Fasten
Seat Belt This message is indicated when the
AUTOHOLD switch is pressed with
the driver’s seat belt unfastened or
the driver’s door open. Fasten the driver's seat belt and press
the AUTOHOLD switch with the driv-
er’s door closed.
Wiper Blades Must Be
on Windshield Before
Operating This message is indicated when the
power switch is switched ON with
the wiper arms at the service posi-
tions.
Return the wiper arms to the initial
positions.
Windshield Wiper Range
of Motion Reduced. Re-
move Obstruction(s) This message is indicated when there
is snow or dirt accumulation on the
windshield and the wiper operation
range is narrowed.
Remove foreign matter from the
windshield.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-34
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 482 of 547

Warning Sound isActivated
▼Lights-On Reminder
The lights-on reminder is operable
when the time setting*1 of the auto
headlight o ff function is o ff.
If the power switch is switched OFF
with the exterior li ghts turned on and
the driver’s door is opened, a sound is
activated.
Operate the headlight switch to turn
o ff the exterior lights.
*1 If the light switch is left on, the
auto headlight o ff function
automatically turns off the lights
about 30 seconds after switching
the EV system off. The time setting
can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the power switch is switched
to ACC, the “Power Switch Not
Switched OFF (STOP) Warning Beep”
(page 7-37) overrides the lights-on
reminder.
A personalized function is available
to change the sound volume for the
lights-on reminder.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼ Seat Belt Warning Beep
Front seat
If the driver's seat belt is not fastened
when the power switch is switched
ON, a beep sound will be heard for
about 6 seconds. If the driver or the
front passenger's seat belt is not
fastened and if the vehicle is driven at
about 20 km/h (12 mph) or faster, or
about 10 km/h (6 mph) or faster for a
continuous 30 seconds, with the seat
belt unfastened, a sound is activated
continuously for a certain period.
Until a seat belt is fastened or a given
period of time has elapsed, the beep
sound will not stop even if the vehicle
speed falls below 20 km/h (12 mph).
NOTE
To allow the front passenger
occupant classi
fication sensor to
function properly, do not place and
sit on an additional seat cushion on
the front passenger's seat. The
sensor may not function properly
because the additional seat cushion
could cause sensor interference.
If a small child is seated on the front
passenger's seat, the warning beep
may not operate.
Rear seat
The warning beep only sounds if a seat
belt is unfastened after being fastened.
▼ Power Switch Not Switched OFF
(STOP) Warning Beep
If the driver's door is opened with the
power switch switched to ACC, a beep
will be heard continuously in the cabin
to notify the driver that the power
switch has not been switched OFF
(STOP). Under this condition, the
keyless entry system will not operate,
the vehicle cannot be locked, and the
battery voltage will be depleted.
▼Key Removed from Vehicle
Warning Beep
Vehicles with advanced keyless
function
If the key is taken out of the vehicle
while the power switch is switched to
ACC or ON, and all the doors are
closed, a sound is activated 6 times
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-37
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 484 of 547

▼Brake System Warning Beep
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an Authorized Mazda Dealer.
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Shift Position Warning Beep
A warning sound is activated when the
selector lever position and the shift
position of the vehicle do not match.
Check the selector lever position.
▼Selector Lever Not In P or N
Reminder Warning Beep
A warning sound is activated if the
following operations are performed
while the selector lever is in a position
other than P.
The power switch is switched OFF
while the EV system is operating.
The driver’s seat belt is unfastened
and the driver’s door is opened.
Check the selector lever position.
▼ Electric Parking Brake (EPB)
War n in g Be ep
The warning buzzer is activated under
the following conditions:
The vehicle is driven with the parking
brake applied.
The Electric Parking Brake (EPB)
switch is pulled while the vehicle is
driven.
You attempt to start driving the
vehicle while the conditions for
releasing the Electric Parking Brake
(EPB) automatically have not been
met.
▼
AUTOHOLD Warning Beep
Message is displayed and beep sound
is activated simultaneously for about 5
seconds when using AUTOHOLD
function or when AUTOHOLD switch
is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.
If the message is displayed and the
beep sound is activated
simultaneously, have your vehicle
inspected at an Authorized Mazda
Dealer.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the center display.
Brake
fluid amount decreaseElectric Parking Brake (EPB) problemShift control system problemEV System problemCharging system problemApproaching vehicle audible system
problem
▼Reverse Position Warning Beep
The warning beep is activated when
the power switch is switched ON and
the selector lever is in the R position.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-39
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 506 of 547

Event Data Recorder
(U.S.A. and Canada)
▼ Event Data Recorder
This vehicle is equipped with an event
data recorder (EDR). The main
purpose of an EDR is to record, in
certain crash or near crash-like
situations, such as an air bag
deployment or hitting a road obstacle,
data that will assist in understanding
how a vehicle’s systems performed.
The EDR is designed to record data
related to vehicle dynamics and safety
systems for a short period of time,
typically 30 seconds or less. The EDR in
this vehicle is designed to record such
data as:
How various systems in your vehicle
were operating;
Whether or not the driver and
passenger safety belts were buckled/
fastened;
How far (if at all) the driver was
depressing the accelerator and/or
brake pedal; and,
How fast the vehicle was traveling.
These data can help provide a better
understanding of the circumstances in
which crashes and injuries occur.
NOTE :
EDR data are recorded by your vehicle
only if a non-trivial crash or near
crash-like situation occurs; no data are
recorded by the EDR under normal
driving conditions and no personal
data (e.g., name, gender, age, and
crash location) are recorded. However,
other parties, such as law
enforcement, could combine the EDR
data with the type of personally
identifying data routinely acquired
during a crash investigation.
To read data recorded by an EDR,
special equipment is required, and
access to the vehicle or the EDR is
needed. In addition to the vehicle
manufacturer, other parties, such as
law enforcement, that have the special
equipment, can read the information if
they have access to the vehicle or the
EDR.
Mazda will not disclose any of the data
recorded in an EDR to a third party
unless:
A written agreement from the vehicle
owner or the lessee is obtained
O fficially requested by the police or
other law enforcement authorities
Used as a defense for Mazda in a
lawsuit, claim, or arbitration
Ordered by a judge or court
However, if necessary Mazda will:
Use the data for research on Mazda
vehicle performance, including
safety.
Disclose the data or the summarized
data to a third party for research
purposes without disclosing vehicle
or owner identi fication information.
Customer Information and Reporting Safety Defects
Event Data Recorder
8-17
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07
Page 542 of 547

Index
Compass display.................. 4-18
Dashboard illumination........ 4-14
Distance-to-full Discharge..... 4-16
High Voltage Battery Power
Gauge..................................4-14
High Voltage Battery Temperature
Gauge..................................4-13
Indication/indicator lights..... 4-21
Instantaneous Energy Efficiency .....
........................................... 4-17
i-ACTIVSENSE display........... 4-17
Message Display................... 4-18
Message indicated on multi-
information display............... 7-33
Multi-information display...... 4-11
Odometer............................ 4-13
Outside temperature
display................................. 4-15
Power Meter.......................... 4-9
Remaining High Voltage Battery
Power Indication.................. 4-16
Speedometer......................... 4-9
Trip meter............................ 4-13
Warning indication/warning
lights....................................4-19
Interior Care............................. 6-40 Active driving display
maintenance........................ 6-42
Cleaning the floor mats......... 6-42
Glass and Mirror
Maintenance........................ 6-42
Instrument panel top (Soft pad)
maintenance........................ 6-41
Leather upholstery
maintenance........................ 6-41
Panel and Cork Area
Maintenance........................ 6-42
Plastic part maintenance....... 6-41
Seat belt maintenance.......... 6-40
Upholstery and synthetic leather
maintenance........................ 6-40Vinyl upholstery
maintenance........................ 6-40
Interior Lights............................ 5-37 Luggage compartment light... 5-37
Map lights............................5-37
Overhead lights.................... 5-37
i-ACTIVSENSE........................... 4-68 Active safety technology........ 4-68
Adaptive Front Lighting System
(AFS)................................... 4-82
Blind Spot Monitoring
(BSM).................................. 4-87
Camera and sensors............. 4-69
Cruising & Traffic Support
(CTS)................................. 4-118
Distance & Speed Alert
(DSA).................................. 4-99
Driver Attention Alert
(DAA)................................ 4-100
Driver monitoring camera..... 4-81
Driver Monitoring (DM)...... 4-102
Emergency Lane Keeping
(ELK).................................. 4-129
Forward Sensing Camera
(FSC)................................... 4-71
Front camera/side cameras/rear
camera................................ 4-81
Front Cross Traffic Alert
(FCTA)............................... 4-104
Front radar sensor.................4-75
Front side radar sensor.......... 4-77
High Beam Control System
(HBC).................................. 4-83
i-ACTIVSENSE OFF Switch..... 4-70
i-ACTIVSENSE status symbol
(warning/risk avoidance support
system)................................ 4-69
Lane Departure Warning System
(LDWS)................................ 4-84
Lane-keep Assist System
(LAS)..................................4-127
10-5
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07