trunk MAZDA MODEL MX-5 2005 (in English) User Guide

Black plate (57,1)
qOpening the Trunk Lid from the
Inside
Pull the illuminated“T”shaped handle.
The handle is made of material that will
glow for hours in the darkness of the
trunk following a brief exposure to
ambient light.
The“T”shaped handle is located on the
inside of the trunk end trim.
Handle
CAUTION
Always keep the handle firmly attached
to the holder and in the recessed
position. Not securing the handle this
way could allow it to snag luggage in
the trunk and open the trunk lid.
Power Windows
The ignition switch must be in the ON
position for the power windows to
operate.
WARNING
Closing Power Windows:
Closing power windows are
dangerous. A person's hands, head, or
even neck could be caught by the
window and result in serious injury or
even death.
This warning applies especially to
children. Make sure the opening is
clear before closing a window.
Keys and Children:
Leaving children in a vehicle with the
key is dangerous. This could result in
someone being badly injured or even
killed. They could play with power
windows or other controls, or even
make the vehicle move. Don't leave the
keys in your vehicle with children and
keep them in a place where your
children will not find or play with
them.
Knowing Your Mazda
Doors and Locks
3-15
MX-5 Miata_8T72-EA-04G_Edition1 Page57
Wednesday, June 9 2004 3:4 PM
Form No.8T72-EA-04G

Black plate (64,1)
6. Lift up on the front section of the top to
release it from the windshield header.
Windshield header
7. Fold back the front and carefully lower
it to the storage area, then put the
latches in the locked position.
qCovering the Convertible Top
1. Cover the convertible top with the top
covering, stored in the trunk.
2. Feed the straps on the bottom of the
covering through the lower links and
snap them into position.
Top covering
LinkStrap
3. Secure the top covering with the straps.
4. Affix the top covering fasteners.
5. Insert the top covering's rear edge into
the groove in the body molding.
Top covering
Body
Molding
CAUTION
Never drive with the top partially
folded or uncovered. Otherwise the top
and/or the top covering could be
damaged.
3-22
Knowing Your Mazda
Doors and Locks
MX-5 Miata_8T72-EA-04G_Edition1 Page64
Wednesday, June 9 2004 3:4 PM
Form No.8T72-EA-04G

Black plate (65,1)
qRaising the Convertible Top
1. Park the vehicle on a level surface and
firmly set the parking brake.
2. Lower the side windows, then turn off
the ignition.
3. Pull down the sunvisors.
Sunvisor
Sunvisor
4. Undo the fasteners and straps.
5. Remove the top covering and store it
properly in the trunk.
6. Unlock the top latches and open them
fully.
7. Hold the top lift handle and pull the top
up and forward until it's against the
windshield header.
Windshield header
8. After securely hooking the top latches
onto the windshield header, push each
latch up with the palm of your hand
until the lock buttons click and the
latches are locked.
CAUTION
Make sure the top is securely locked by
pushing up on it.
Driving with the top unlocked could
damage the top.
NOTE
Make sure the top is securely locked by
pushing up on it. If it still sounds loose
(rattles) after being locked by the top
latches, have it inspected at an
Authorized Mazda Dealer.
Knowing Your Mazda
Doors and Locks
3-23
MX-5 Miata_8T72-EA-04G_Edition1 Page65
Wednesday, June 9 2004 3:4 PM
Form No.8T72-EA-04G

Black plate (208,1)
WARNING
Metric Studs and Lug Nuts:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip off
and cause an accident. Be sure to
reinstall the same nuts you removed or
replace them with metric nuts of the
same configuration.
Incorrect Tire Air Pressure:
Driving on tires with incorrect air
pressure is dangerous. Tires with
incorrect pressure could affect
handling and result in an accident.
Don't drive with any tires that have
incorrect air pressure. When you
check the regular tires' air pressure,
check the spare tire, too.
5. Store the damaged tire in the trunk.
Have the damaged tire repaired as soon
as possible.
NOTE
To prevent the jack and tool from
rattling, store them properly.
7-10
In Case of an Emergency
Flat Tire
MX-5 Miata_8T72-EA-04G_Edition1 Page208
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (211,1)
Starting a Flooded Engine
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and
hold it there.
2. Turn the ignition switch to the START
position and hold it there―for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it
without depressing the accelerator―for
up to 10 seconds.
Jump-Starting
The battery is in the trunk.
Jump-starting is dangerous if done
incorrectly. So follow the procedure
carefully. If you feel unsure about jump-
starting, we strongly recommend that you
have a competent service technician do
the work.
WARNING
Battery-Related Explosion:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from open
battery cells.
Frozen Battery:
Jump-starting a frozen battery is
dangerous. It may rupture or explode,
causing serious injury.
Don't jump-start a frozen battery.
CAUTION
Use only a 12 V booster system. You
can damage a 12 V starter, ignition
system, and other electrical parts
beyond repair with a 24 V power
supply (two 12 V batteries in series or a
24 V motor generator set).
1. Make sure the booster battery is 12 V
and that its negative terminal is
grounded.
In Case of an Emergency
Emergency Starting
7-13
MX-5 Miata_8T72-EA-04G_Edition1 Page211
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (212,1)
2. If the booster battery is in another
vehicle, don't allow the vehicles to
touch. Turn off the engine of the
vehicle with the booster battery and all
unnecessary electrical loads in both
vehicles.
3. Connect the jumper cables in the exact
sequence as in the illustration.
lConnect one end of a cable to the
positive terminal on the discharged
battery (1).
lAttach the other end to the positive
terminal on the booster battery (2).
lConnect one end of the other cable
to the negative terminal of the
booster battery (3).
lConnect the other end to a solid,
stationary, exposed metallic point
(for example, the trunk latch catch)
away from the discharged battery
(4).
Booster battery
Jumper
cable
Discharged
battery
Connect cables
in numerical
order and
disconnect in
reverse order.
Jumper cable
WARNING
Connecting to Negative Terminal:
Connecting the end of the second
cable to the negative (
) terminal of
the discharged battery is dangerous.
A spark could cause the gas around
the battery to explode and injure
someone. Connect the cable to a point
away from the battery.
4. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle.
5. When finished, carefully disconnect the
cables in the reverse order described in
Step3.
7-14
In Case of an Emergency
Emergency Starting
MX-5 Miata_8T72-EA-04G_Edition1 Page212
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (229,1)
Engine Compartment Overview
Fuse block
Engine oil-filler cap
Cooling system cap
Power steering fluid filler cap/dipstickAir filterClutch fluid reservoir
(Only for manual
transmission model) Automatic transmission fluid-level dipstick
(Only for automatic transmission model)
Engine oil dipstick
Brake fluid reservoir Washer fluid reservoir
(TypeA)
Engine coolant
reservoirWasher fluid reservoir (TypeB)
The battery is in the trunk
Maintenance and Care
Owner Maintenance
8-13
MX-5 Miata_8T72-EA-04G_Edition1 Page229
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (245,1)
The battery is in the trunk.
qBattery Maintenance
To get the best service from a battery:
lKeep it securely mounted.
lKeep the top clean and dry.
lKeep terminals and connections clean,
tight, and coated with petroleum jelly
or terminal grease.
lRinse off spilled electrolyte
immediately with a solution of water
and baking soda.
lIf the vehicle will not be used for an
extended time, disconnect the battery
cables.
Tires
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tire inflation pressures and
stay within the recommended load limits
and weight distribution.
WARNING
Using Different Tire Types:
Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor
braking; leading to loss of control.
Except for the limited use of the
temporary spare tire, use only the
same type tires (radial, bias-belted,
bias-type) on all four wheels.
Using Wrong-Sized Tires:
Using any other tire size than what is
specified for your Mazda (page 10-6)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for your
Mazda.
Maintenance and Care
Owner Maintenance
8-29
MX-5 Miata_8T72-EA-04G_Edition1 Page245
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (249,1)
Light Bulbs
Overhead light
High-mount brake light
Rear turn signal lights Brake lights/Taillights
Reverse lights
Headlights
Some models.
License plate
lights/Trunk lights Side-marker lightsFog lights Front turn signal
lights/Parking lights
Maintenance and Care
Owner Maintenance
8-33
MX-5 Miata_8T72-EA-04G_Edition1 Page249
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G

Black plate (251,1)
2. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
3. Install the new bulb in the reverse order
of removal.
Side-marker lights
1. Remove the bolts with a Phillips
screwdriver and remove the side-
marker light unit.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Pull the center section of the plastic
retainer and remove the retainers and
remove the trunk end trim.
Removal
Installation
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
Reverse lightsBrake lights/Taillights Rear turn signal lights
4. Install the new bulb in the reverse order
of removal.
High-mount brake light
1. Turn the socket and bulb assembly
counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-35
MX-5 Miata_8T72-EA-04G_Edition1 Page251
Wednesday, June 9 2004 3:6 PM
Form No.8T72-EA-04G