ABS MAZDA MODEL MX-5 2016 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2016, Model line: MODEL MX-5, Model: MAZDA MODEL MX-5 2016Pages: 526, PDF Size: 28.82 MB
Page 197 of 526

4–93
When Driving
Tire Pressure Monitoring System
*Some models.
Tire Pressure Monitoring System*
The Tire Pressure Monitoring System (TPMS) monitors the air pressure of all\
four tires. If
the air pressure of one or more tires is too low, the system warns the driver by indicating the
tire pressure monitoring system warning light in the instrument cluster \
and operating a beep
sound. The system monitors the tire pressures indirectly using the data sent from the ABS
wheel speed sensors.
To allow the system to operate correctly, the system needs to be initialized with the specified
tire pressure (value on the tire pressure label). Follow the procedure\
and perform the
initialization.
Refer to Tire Pressure Monitoring System Initialization on page 4-96.
The warning light flashes when the system has a malfunction.
Refer to Warning Lights on page 4-16.
ABS wheel speed sensor
MX-5_8EU4-EA-15D_Edition1.indb 932015/03/10 9:55:20
Page 373 of 526

6–35
Maintenance and Care
Owner Maintenance
CAUTION
To prevent damage to the windshield
let the wiper arm down easily, don't let
it slap down on the windshield.
2. Hold the end of the rubber and pull
until the tabs are free of the metal
support.
Metal support
Ta b
3. Remove the metal stiffeners from each
blade rubber and install them in the
new blade.
CAUTION
Do not bend or discard the stiffeners. You
need to use them again. If the metal stiffeners are switched,
the blade's wiping efficiency could be
reduced.
So don't use the driver's side metal
stiffeners on the passenger's side, or vice
versa. Be sure to reinstall the metal stiffeners in
the new blade rubber so that the curve
is the same as it was in the old blade
rubber.
4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
MX-5_8EU4-EA-15D_Edition1.indb 352015/03/10 9:56:09
Page 393 of 526

6–55
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTIONFUSE RATINGPROTECTED COMPONENT
18A/C MAG7.5 AAir conditioner
19AT PUMP20 ATransmission control system*
20AT15 ATransmission control system*
21D LOCK25 APower door locks
22H/L RH20 AHeadlight (RH)
23ENGB27.5 AEngine control system
24TAIL20 ATaillights, License plate lights, Parking lights
25DRL15 A—
26ROOM25 AOverhead light
27FOG15 A—
28H/CLEAN20 A—
29STOP10 ABrake lights
30HORN15 AHorn
31H/L LH20 AHeadlight (LH)
32ABS/DSC S30 AABS, Dynamic stability control system
33HAZARD15 AHazard warning flashers, Turn signal lights
34FUEL PUMP15 AFuel system
35ENGB35 A—
36WIPER20 AWindshield wipers
37CABINB50 AFor protection of various circuits
38———
39———
40ABS/DSC M50 AABS, Dynamic stability control system
41EVVTA/R PUMP20 AEngine control system
42EVPS30 ABrake control system
43FAN130 ACooling fan
44FAN240 A—
45ENG.MAIN40 AEngine control system
46EPS60 APower steering system
47DEFOG30 ARear window defogger
48IG230 AFor protection of various circuits
49INJECTOR30 AEngine control system
50HEATER40 AAir conditioner
51———
52———
MX-5_8EU4-EA-15D_Edition1.indb 552015/03/10 9:56:17
Page 410 of 526

7–4
If Trouble Arises
Flat Tire
*Some models.
Jack*
To remove the jack
1. Remove the cover.
2. Turn the wing bolt and jack screw
counterclockwise.
Wing bolt
Jack screw
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing back and turn
the wing bolt clockwise to temporarily
tighten it.
2. Turn the jack screw clockwise.
Wing bolt
Jack screw
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is sufficiently tightened.
4. Insert the cover tabs and install the
cover.
NOTE
Verify that the cover is securely installed.
Maintenance
Always keep the jack clean. Make sure the moving parts are kept
free from dirt or rust. Make sure the screw thread is
adequately lubricated.
MX-5_8EU4-EA-15D_Edition1.indb 42015/03/10 9:56:20
Page 414 of 526

7–8
If Trouble Arises
Flat Tire
10. Install the bottle to the air compressor
and press it in until the left and right
tabs are engaged securely.
Tabs
11. Insert the air compressor plug into the
accessory socket inside the vehicle and
switch the ignition to ACC.
Refer to Accessory Sockets on page
5-133.
Compressor
Compressor plug
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that the
air compressor switch is off. When
turning the air compressor on/off, use
the air compressor switch.
12. The sealant is injected into the tire
when the air compressor is switched
on. After the sealant is injected
completely, wait until the tire inflation
pressure increases to the specified tire
inflation pressure.
NOTE
The inflation pressure may increase to
about 300 kPa (3.1 kgf/cm2, 3 bar, 43.5
psi) temporarily to inject the sealant
through the valve. Normally, the inflation
pressure decreases gradually and it
reaches the actual inflation pressure after
about 30 seconds.
WARNING
Never use the air compressor above 300
kPa (3.1 kgf/cm2, 3 bar, 43.5 psi):
Using the air compressor at an
inflation pressure above 300 kPa (3.1
kgf/cm2, 3 bar, 43.5 psi) continuously
is dangerous. If the air compressor
overheats, hot air will be exhausted
and you could get burned.
CAUTION
If the air compressor operates slowly
or becomes hot, this indicates
overheating. Turn the air compressor
off immediately and cancel the
procedure. In this case, leave the air
compressor turned off for about 30
minutes or longer and wait until the
temperature decreases.
MX-5_8EU4-EA-15D_Edition1.indb 82015/03/10 9:56:22
Page 440 of 526

7–34
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
SignalWarning
Electronic Brake Force Distribution System Warning
If the electronic brake force distribution control unit determines that \
some components are operating incorrectly, the control unit may illuminate the brake system warning light and the ABS warning light simultaneously. The problem is likely to be the electronic brake force distribution system.
WARNING
Do not drive with both the ABS warning light and brake warning light illuminated. Have the vehicle towed to an Authorized Mazda Dealer to have the brakes inspected as soon as possible:Driving when the brake system warning light and ABS warning light are illuminated simultaneously is dangerous.When both lights are illuminated, the rear wheels could lock more quickly in an emergency stop than under normal circumstances.
Charging System Warning Light
If the warning light illuminates while driving, it indicates a malfuncti\
on of the alternator or of the charging system.Drive to the side of the road and park off the right-of-way. Consult an Authorized Mazda Dealer.
CAUTION
Do not continue driving when the charging system warning light is illuminated because the engine could stop unexpectedly.
Engine Oil Warning Light
This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in extensive engine damage.If the light illuminates or the warning indication is displayed while dr\
iving:
1.Drive to the side of the road and park off the right-of-way on level ground.2.Turn off the engine and wait 5 minutes for the oil to drain back into the oil p\
an.3.Inspect the engine oil level 6-28. If it's low, add the appropriate amount of engine oil while being careful not to overfill.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive engine damage.4.Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or \
after adding oil, stop the engine immediately and have your vehicle towed to an Authorized Mazda Dealer.
MX-5_8EU4-EA-15D_Edition1.indb 342015/03/10 9:56:30
Page 442 of 526

7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
SignalWarning
Electric Vacuum Pump Warning Light
The light turns on if the electric vacuum pump system has a problem. Hav\
e your vehicle inspected at an Authorized Mazda Dealer.
ABS Warning Light
If the ABS warning light stays on while you're driving, the ABS control unit has detected a system malfunction. If this occurs, your brakes will function normally a\
s if the vehicle had no ABS.Should this happen, consult an Authorized Mazda Dealer as soon as possible.
NOTE
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS warning light may illuminate. If this occurs, it is the result of the weak battery and does not indicate an ABS malfunction.Recharge the battery.The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light
If this light illuminates while driving, the vehicle may have a problem.\
It is important to note the driving conditions when the light illuminated and consult an Authorized Mazda Dealer.The check engine light may illuminate in the following cases:
The fuel tank level being very low or approaching empty.The engine's electrical system has a problem.The emission control system has a problem.The fuel-filler cap is missing or not tightened securely.If the check engine light remains on, or it flashes continuously , do not drive at high speeds and consult an Authorized Mazda Dealer as soon as possible.
Automatic Transmission Warning Light*
The light illuminates when the transmission has a problem.
CAUTION
If the automatic transmission warning light illuminates, the transmission has an electrical problem. Continuing to drive your Mazda in this condition could cause damage to your transmission. Consult an Authorized Mazda Dealer as soon as possible.
Air Bag/Seat Belt Pretensioner System Warning Light
A system malfunction is indicated if the warning light constantly flashes, constantly illuminates or does not illuminate at all when the ignition is switched ON. If any of these occur, consult an Authorized Mazda Dealer as soon as possible. The system may not operate in an accident.
WARNING
Never tamper with the air bag/pretensioner systems and always have an Authorized Mazda Dealer perform all servicing and repairs:Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner could accidentally activate or become disabled causing serious injury or death.
MX-5_8EU4-EA-15D_Edition1.indb 362015/03/10 9:56:31
Page 474 of 526

8–18
Customer Information and Reporting Safety Defects
Warranty
Add-On Non-Genuine Parts and Accessories
Non-genuine parts and accessories for Mazda vehicles can be found in stores.
These may fit your vehicle, but they are not approved by Mazda for use with Mazda
vehicles. When you install non-genuine parts or accessories, they could affect your vehicle's
performance or safety systems; the Mazda warranty doesn't cover this. Before you install
any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
WARNING
Always consult an Authorized Mazda Dealer before you install non-genuine parts or
accessories:
Improperly designed parts or accessories could seriously affect your vehicle's performance
or safety systems. This could cause you to have an accident or increase your chances of
injuries in an accident.
Be very careful in choosing and installing add-on electrical equipment, such as mobile
telephones, two-way radios, stereo systems, and car alarm systems:
Incorrectly choosing or installing improper add-on equipment or choosing an improper
installer is dangerous. Essential systems could be damaged, causing engine stalling, air-
bag (SRS) activation, ABS/TCS/DSC inactivation, or a fire in the vehicle.
Mazda assumes no responsibility for death, injury, or expenses that may result from the
installation of add-on non-genuine parts or accessories.
MX-5_8EU4-EA-15D_Edition1.indb 182015/03/10 9:56:36
Page 492 of 526

8–36
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
Vehicle Loading
WARNING
Do not tow a trailer with this vehicle:
Towing a trailer with this vehicle is dangerous because it has not been designed to tow a
trailer and doing so will affect the drive system which could result in vehicle damage.
This section will guide you in the proper loading of your vehicle, to ke\
ep your loaded
vehicle weight within its design rating capability. Properly loading your vehicle will provide
maximum return of vehicle design performance. Before loading your vehicle, familiarize
yourself with the following terms for determining your vehicle's weight \
ratings, from the
vehicle's Safety Certification Label and Tire and Load Information Label:
WARNING
Overloaded Vehicle:
Overloading a vehicle is dangerous. The results of overloading can have serious
consequences in terms of passenger safety. Too much weight on a vehicle's suspension
system can cause spring or shock absorber failure, brake failure, handling or steering
problems, irregular tire wear, tire failure or other damage.
Overloading makes a vehicle harder to drive and control. It also increases the distance
required for stopping. In cases of serious overloading, brakes can fail completely,
particularly on steep grades. The load a tire will carry safely is a combination of the size of
the tire, its load range, and corresponding inflation pressure.
Never overload the vehicle and always observe the vehicle's weight ratings from the
vehicle's Safety Certification and Tire and Load Information labels.
MX-5_8EU4-EA-15D_Edition1.indb 362015/03/10 9:56:39
Page 520 of 526

10–2
Index
A
Accessory Socket ..............................5-133
Adaptive Front Lighting System
(AFS)...................................................4-65
Add-On Non-Genuine Parts and
Accessories .........................................8-18
Advanced Key
Advanced keyless entry system ......3-8
Operational range ............................3-9
Air Bag/Seat Belt Pretensioner System
Warning Beep ......................................7-45
Air Bag Systems .................................2-24
Ambient Temperature Display ............4-13
Antilock Brake System (ABS) ............4-55
Audio Control Switch
Adjusting the volume ....................5-55
Seek switch....................................5-56
Audio System ......................................5-13
AUX/USB/iPod mode ...................5-57
Antenna .........................................5-13
Audio control switch .....................5-55
Audio set (Type A) ........................5-22
Audio set (Type B) ........................5-34
Operating tips for audio system ....5-14
Satellite radio ................................5-46
Automatic Transmission .....................4-24
Active Adaptive Shift (AAS) ........4-26
Direct mode ...................................4-33
Driving tips....................................4-33
Manual shift mode.........................4-27
Shift-lock override ........................4-26
Shift-lock system ...........................4-26
Shift position indication ................4-25
Transmission ranges ......................4-25
Warning light .................................4-25
B
Back Trim Storage Box .....................5-138
Battery .................................................6-36
Maintenance ..................................6-38
Replacement ..................................6-38
Specifications ..................................9-4
Battery Runs Out
.................................7-23
Jump-starting .................................7-23
Blind Spot Monitoring (BSM) ............4-74
Blind Spot Monitoring (BSM) System
Warning Beep ......................................7-48
Bluetooth® ...........................................5-74
Bluetooth® audio (Type A) ..........5-112
Bluetooth® audio (Type B) ..........5-114
Bluetooth® Hands-Free (Type A) ...5-96
Bluetooth® Hands-Free (Type B) ...5-102
Troubleshooting ..........................5-128
Body Lubrication ................................6-32
Brakes
Brakes assist ..................................4-53
Foot brake......................................4-51
Pad wear indicator .........................4-52
Parking brake ................................4-52
Warning light .................................4-52
Break-In Period ...................................3-43
C
Capacities ..............................................9-5
Carbon Monoxide ...............................3-24
Cell Phones .........................................8-19
Child Restraint
Child-restraint precautions ............2-15
Child-restraint system installation ...2-20
Installing child-restraint systems...2-21
Climate Control System ........................5-2
Fully automatic type ........................5-9
Gas specifications ............................9-6
Manual type .....................................5-5
Operating tips ..................................5-2
Vent operation .................................5-3
Clock ...................................................5-26
MX-5_8EU4-EA-15D_Edition1.indb 22015/03/10 9:56:47