headlight bulb MAZDA MODEL MX-5 2020 Owners Manual (in English)

Light Bulbs
Overhead lightSide turn signal lights
High-mount brake light
Trunk light
Front side-marker lights
Front turn signal lights
Headlights (Low/High beam)
P
arking lights
Daytime running lights
License plate lights
Brake lights
Taillights
Rear side-marker lights
Reverse lights
Rear turn signal lights
Maintenance and Care
Owner Maintenance
6-42
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06

CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
▼Replacing Exterior Light Bulbs
Headlights, Daytime running lights
(LED type), Parking lights, High-mount
brake light, Brake lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Daytime running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers.

Removal
Installation
Maintenance and Care
Owner Maintenance
6-43
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06

Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start the engine, turn the steering wheel all
the way to the rig ht, and turn off
engine. If you are changing the left
bulb, turn the steerin g wheel to the left.
3. Pull the center of each plastic retainer and remove the retainers, and then
partially peel back the mudguard.

Removal
Installation
4. Disconnect the connector from the unitby pressing the tab on the connector
with your finger and pulling the
connector rearward.

5. Turn the socket and bulb assemblycounterclockwise and remove it.
6. Disconnect the bulb from the socket.

7. Install the new bulb in the reverseorder of the removal procedure.
Side turn signal lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
Maintenance and Care
Owner Maintenance
6-45
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06

9. After the hook is detached, pull out the
rear combination lamp unit in the
direction of the arrow and remove it.

Grommet installation hole
Clip
Hook Rear combination
lamp unit
CAUTION
Carefully pull out the rear combination
lamp unit when removing it from the
body.
The wiring may become damaged if the
rear combination lamp unit is forcefully
pulled out.
10. Turn the socket and bulb assembly counterclockwise and remove it.
11. Disconnect the bulb from the socket.
12. Install the new bulb in the reverse
order of the removal procedure.
Rear side-marker lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverseorder of the removal procedure.
Maintenance and Care
Owner Maintenance
6-49
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06

Reverse lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverseorder of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,and the headligh t switch is off.
2. Remove the unit by pressing the tab on the unit with your finger and pulling
the unit downward.

3. Turn the socket and bulb assemblycounterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
Maintenance and Care
Owner Maintenance
6-50
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06

▼Light Bulbs
Exterior light
Light bulbCategory
Wattage UN-R*1 (SAE)
Headlights High beam
LED
*2― (―)
Low beam LED
*2― (―)
Daytime running lights LED type
LED
*2― (―)
Bulb type 21W21W (7440)
Parking lights LED
*2― (―)
Front side-marker lights 5W5W (―)
Front turn signal lights 28/8― (7444NA)
Side turn signal lights 5
*3WY5W (―)
High-mount brake light LED
*2― (―)
Rear turn signal lights 21WY21W (7443NA)
Rear side-marker lights 5W5W (―)
Brake lights LED
*2― (―)
Taillights LED
*2― (―)
Reverse lights 21W21W (7440)
License plate lights 5W5W (―)
*1 UN-R stands for Unite d Nations Regulation.*2 LED is the abbreviation for Light Emitting Diode.*3 Bulb replacement is not possibl e because it is built into the unit. Replace the unit.

Interior light
Light bulb Category
Wattage UN-R*1
Overhead light 10―
Trunk light 5―
*1 UN-R stands for United Nations Regulation.
Specifications
Specifications
9-7
MX-5_8JA4-EA-19K_Edition2 _old 2019-8-29 16:18:06