clock MAZDA MODEL MX-5 MIATA 2006 Owner's Manual

Black plate (254,1)
qLocking Lug Nuts
If your vehicle has optional antitheft
wheel lug nuts, one on each wheel will
lock the tires and you must use a special
key to unlock them. This key is attached
to the lug wrench. Register them with the
lock manufacturer by filling out the card
provided in the glove box and mailing it
in the accompanying envelope. If you lose
this key, consult an Authorized Mazda
Dealer or use the lock manufacturer's
order form, which is with the registration
card.
Special key
Antitheft lug nut
To remove an antitheft lug nut
1. Obtain the key for the antitheft lug nut.
2. Place the key on top of the nut, and be
sure to hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Don't use a
power impact wrench.
3. Place the lug wrench on top of the key and apply pressure. Turn the wrench
counterclockwise.
To install the nut
1. Place the key on top of the nut, and besure to hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Don't use a
power impact wrench.
2. Place the lug wrench on top of the key, apply pressure, and turn it clockwise.
qMounting the Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
WARNING
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
7-16
In Case of an Emergency
Flat Tire
MX-5_8U35-EA-05F_Edition4 Page254
Thursday, October 6 2005 11:5 AM
Form No.8U35-EA-05F

Black plate (255,1)
2. Mount the tire.
3. Install the lug nuts with the bevelededge inward; tighten them by hand.
WARNING
Don't Apply Oil or Grease to Lug
Nuts, Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the tire
to come off, resulting in an accident.
In addition, lug nuts and bolts could
be damaged if tightened more than
necessary. Do not apply oil or grease
to lug nuts and bolts and do not
tighten the lug nuts beyond the
recommended tightening torque. 4. Turn the jack handle counterclockwise
and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you're unsure of how tight the nuts
should be, have them inspected at an
Authorized Mazda Dealer.
Nut tightening torque
N·m (kgf·m, ft·lbf) 88
―118
(9 ― 12, 65 ―87)
In Case of an Emergency
Flat Tire
7-17
MX-5_8U35-EA-05F_Edition4 Page255
Thursday, October 6 2005 11:5 AM
Form No.8U35-EA-05F

Black plate (288,1)
To change coolant
WARNING
Removing the Cooling System Cap:
Removing the cooling system cap
while the engine is running or hot is
dangerous. This might lead to cooling
system and engine damage and could
result in serious injury from escaping
hot coolant or steam. Turn off the
engine and wait until it's cool. Even
then, be very careful when removing
the cap. Wrap a thick cloth around the
cap and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you're sure all the pressure is
gone, press down on the cap―still
using a cloth ―turn the cap, and
remove it.
1. Make sure the engine is not running and it has cooled.
2. Remove the cooling system cap.
Tighten Tighten
Loosen Loosen
3. Remove the radiator drain plug and
drain the coolant into a suitable
container. Properly dispose of the used
coolant. 4. Flush out the system with running
water.
5. Drain the system completely. Insert and tighten the plug. Add as much
ethylene-glycol-based coolant mixture
and water (or undiluted FL22) as
necessary to provide freezing and
corrosion protection.
6. In extremely cold climates, add the mixture percentage recommended in
the coolant mixture percentage table.
7. Run the engine at idle with the cooling system cap off. Slowly add additional
coolant if necessary.
8. At this point, wait until the engine reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
9. Install the cooling system cap. Inspect all connections for leaks. Inspect the
level in the coolant reservoir one more
time and verify that the coolant level is
between the F and L marks.
8-20
Maintenance and Care
Owner Maintenance
MX-5_8U35-EA-05F_Edition4 Page288
Thursday, October 6 2005 11:5 AM
Form No.8U35-EA-05F

Black plate (304,1)
WARNING
Xenon Fusion Bulb Replacement:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Do not replace the xenon
fusion bulbs yourself. Consult an
Authorized Mazda Dealer when the
replacement is necessary.
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries could
be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
qReplacing Exterior Light Bulbs
Replacing the headlight bulbs
1. Make sure the headlight switch is off.
2. Lift the hood and find the high and low
beam bulbs in the rear of the headlight
body.
The outboard bulb is the LOW beam,
and the inboard one is the HIGH beam.
High-beam bulbs
1. Turn the socket and bulb assembly counterclockwise, and carefully pull it
backward.
2. Disconnect the socket and bulb assembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
3. Install the new socket and bulbassembly in the reverse order of
removal.
8-36
Maintenance and Care
Owner Maintenance
MX-5_8U35-EA-05F_Edition4 Page304
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (305,1)
NOTE
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
of the replacement bulb to dispose of
the old bulb promptly out of the
reach of children.
Low-beam bulbs
(Xenon fusion bulbs)
You cannot replace the low beam bulbs by
yourself.
The bulbs must be replaced at an
Authorized Mazda Dealer.
(Halogen bulbs)
NOTE
Replacing low-beam halogen bulbs is
difficult therefore contacting an
Authorized Mazda Dealer is
recommended.
1. If you are changing the right headlight bulb, start the engine, turn the steering
wheel all the way to the left, and turn
off the engine. If you are changing the
left headlight bulb, turn the steering
wheel to the right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Disconnect the electrical connector from the bulb by pulling it to the rear.
Maintenance and Care
Owner Maintenance
8-37
MX-5_8U35-EA-05F_Edition4 Page305
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (306,1)
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.
7. Swing the retaining spring out andaway to free the headlight bulb.
8. Carefully remove the socket and bulb assembly by pulling it straight back.
9. Remove the headlight bulb from the socket.
10. Install the new socket and bulb
assembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
lWhen reinstalling the sealing cover,
make sure
faces up.
Front fog light bulbsí
1. If you are changing the right Front foglight bulb, start the engine, turn the
steering wheel all the way to the left,
and turn off the engine. If you are
changing the left Front fog light bulb,
turn the steering wheel to the right.
2. Turn the screws counterclockwise and remove them.
8-38
Maintenance and Care
íSome models.
Owner Maintenance
MX-5_8U35-EA-05F_Edition4 Page306
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (307,1)
3. Turn the center section of the plasticretainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise, and carefully pull it
backward.
5. Disconnect the socket and bulb assembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
6. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
lUse the protective cover and carton
of the replacement bulb to dispose of
the old bulb promptly out of the
reach of children.
Front turn signal lights
1. If you are changing the right front turn
signal light bulb, start the engine, turn
the steering wheel all the way to the
left, and turn off the engine. If you are
changing the left front turn signal light
bulb, turn the steering wheel to the
right.
2. Turn the screws counterclockwise and remove them.
Maintenance and Care
Owner Maintenance
8-39
MX-5_8U35-EA-05F_Edition4 Page307
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (308,1)
3. Turn the center section of the plasticretainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order of removal.
Parking lights
1. Turn the socket and bulb assemblycounterclockwise and remove it. 2. Disconnect the bulb from the socket.
3. Install the new bulb in the reverse order
of removal.
Front side-marker lights
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
1. Slide the unit as shown in the figure to remove it.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
8-40
Maintenance and Care
Owner Maintenance
MX-5_8U35-EA-05F_Edition4 Page308
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (309,1)
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse orderof removal.
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Pull the center section of the plasticretainers and remove them, then
remove the trunk end trim.
Removal
Installation
2. On the side the bulb is to be replaced, pull the center section of the plastic
retainers and remove them, then
remove the trunk side trim.
Removal
Installation
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
Brake lights/Taillights Rear turn signal lights
Reverse lights
5. Install the new bulb in the reverse order of removal.
Maintenance and Care
Owner Maintenance
8-41
MX-5_8U35-EA-05F_Edition4 Page309
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F

Black plate (375,1)
C
Clock ................................................. 6-24
Convertible Top ................................ 3-40
Cruise Control ................................... 5-19
Cup Holder ........................................ 6-40
Customer Assistance ........................... 9-2
D
Dashboard Illumination .................... 5-37
Daytime Running Lights ................... 5-53
DefrosterRear window .............................. 5-56
Detachable Hardtop .......................... 3-45
Dimensions ....................................... 10-5
Door Locks ....................................... 3-28
Driving In Flooded Area ................... 4-11
Driving Tips ........................................ 4-7 Automatic transmission .............. 5-18
Break-in period ............................ 4-7
Driving in flooded area .............. 4-11
Hazardous driving ........................ 4-8
Money-saving suggestions ........... 4-7
Rocking the vehicle ...................... 4-9
Winter driving .............................. 4-9
Dynamic Stability Control (DSC) ..... 5-24
DSC OFF indicator light ............ 5-25
DSC OFF switch ........................ 5-26
TCS/DSC Indicator light ............ 5-24
E
Emergency Starting ........................... 7-21Flooded engine ........................... 7-21
Jump-starting .............................. 7-22
Push-starting .............................. 7-26
Emergency Towing ........................... 7-27
Emission Control System .................... 4-3
E
Engine Coolant ....................................... 8-18
Exhaust gas .................................. 4-5
Hood release .............................. 3-38
Oil .............................................. 8-15
Overheating ................................ 7-19
Starting ......................................... 5-4
Engine Compartment Overview ........ 8-14
Engine Coolant Overheating ................................ 7-19
Engine Coolant Temperature
Gauge ................................................ 5-35
Exhaust Gas ........................................ 4-5
Exterior Care ..................................... 8-50
F
Flasher Hazard warning .......................... 5-57
Headlights .................................. 5-52
Flat Tire ............................................... 7-3 Changing .................................... 7-13
Instant Mobility System
(IMS) Emergency Flat Tire Repair
Kit ................................................ 7-6
Tool storage .................................. 7-5
Fluids Classification .............................. 10-4
Owner maintenance .................... 8-11
Fog Lights ......................................... 5-54
Foot Brake .......................................... 5-5
Fuel Filler lid and cap ........................ 3-37
Gauge ......................................... 5-36
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Index
11-3
MX-5_8U35-EA-05F_Edition4 Page375
Thursday, October 6 2005 11:6 AM
Form No.8U35-EA-05F