turn signal MAZDA MODEL MX-5 MIATA POWER RETRACTABLE HARDTOP 2010 Owner's Manual

Black plate (281,1)
Audio unit
The audio unit is used for adjusting the
volume.
qVoice
To prevent the deterioration in voice
recognition rate and voice quality, the
following points must be observed:
lIt is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
lClose the windows and/or the
moonroof to reduce loud noises from
outside the vehicle, or turn down the
airflow of the climate control system
while Bluetooth Hands-Free is being
used. Voice recognition may not
function correctly or voice quality may
deteriorate under the following
conditions.
lA passenger is speaking.lDriving with the window and/or the
moonroof open.
lDriving on bumpy roads.lNoise outside of the vehicle is loud.
(Construction sites, inside tunnels,
excess oncoming traffic, or heavy
rain.)
lOperation noise from turn signals,
wipers, or the horn is heard.
lA/C airflow is strong or wind is
blowing on the microphone.
lThere is noise coming from cargo
loaded in the vehicle.
lVoice commands may not be
recognized depending on the voice. If
the voice commands are not recognized
correctly, repeat the commands in a
louder voice, at a natural pace, as if
speaking to another person.
lDialects or different wording other than
hands-free prompts cannot be
recognized by voice recognition. Speak
in the wording specified by the voice
commands.
NOTE
If the voice recognition performance is not
satisfactory, refer to “Voice Recognition
Learning Function (Speaker Enrollment) ”
(page 6-76).
Please be aware that the voice recognition
may error despite following the above
points.
q Function restrictions while using
Bluetooth Hands-Free
Some functions are limited while
Bluetooth Hands-Free is being used. They
include:
lBeep sound and voice guidance related
to the audio unit are not heard.
lBeep sound related to the A/C
operation is not heard.
qHow to use this section
Descriptions in the text are as follows:
Say: Voice commands to be spoken by
you.
Prompt: Voice guidance output from the
speaker.
NOTE
Say voice commands after the beep sound
[Beep] is heard.
Example)
Say: [Beep] “Dial ”
Prompt: “Number, please ”
Say: [Beep] “XXXXXXXXXXX (Ex.
“ 555-1234 ”) (Telephone number) ”
Interior Comfort
Bluetooth Hands-Free
6-63
MX-5_8AV1-EA-09F_Edition5 Page281
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (295,1)
4. Press the voice recognition/hands-freeswitch with a short press.
5. The voice guidance reads out the voice input command number (refer to the
voice input command list for voice
recognition learning). (Ex. “Please read
phrase 1” )
6. Say: [Beep] “0123456789” (Say the
voice input command for voice
recognition learning (1 to 8) according
to the voice guidance.)
7. Prompt: “Speaker enrollment is
complete, returning to main menu. ”
Voice input command list for voice
recognition learning
When reading out, the following points
must be observed:
lRead out the numbers one at a time
correctly and naturally.
(For example, “1234 ”must be read out
“ one, two, three, four ”, not “twelve, thirty
four ”.)
lDo not read out parentheses. “(” and
hyphens “-” are used for separating
numbers in a phone number.
Ex.
“ (888) 555-1212 ”must be spoken “Eight,
eight, eight, five, five, five, one, two, one,
two. ”
Phrase Command
1 0123456789
2 (888) 555-1212
3 Call
4 Dial
5 Setup
6 Cancel
7 Continue
8 Help
NOTE
After user voice registration is completed,
voice guidance “Speaker enrollment is
complete, returning to main menu ”is
announced.
q DTMF (dual tone multi-
frequency signal) transmission
This function is used when transmitting
DTMF via the user's voice. The receiver
of a DTMF transmission is generally a
home telephone answering machine or a
company's automated guidance call center
(When you send tone signals back
according to the voice guidance
recording).
1. Press the voice recognition/hands-free
switch with a short press.
2. Say: [Beep] “XXXX... send ”(Say
DTMF code)
3. Prompt: “Sending XXXX... (DTMF
code) ”
Interior Comfort
Bluetooth Hands-Free
6-77
MX-5_8AV1-EA-09F_Edition5 Page295
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (304,1)
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and all
the turn signals will flash.
NOTE
lThe turn signals do not work when the
hazard warning lights are on.
lCheck local regulations about the use of
hazard warning lights while the vehicle is
being towed to verify that it is not in
violation of the law.
7-2
In Case of an Emergency
Parking in an Emergency
MX-5_8AV1-EA-09F_Edition5 Page304
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (315,1)
Changing a Tire
WARNING
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a jack:Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Never allow anyone inside a vehicle
supported by a jack: Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
CAUTION
(With Tire Pressure Monitoring
System)
The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not
use non-genuine wheels, otherwise it
may not be possible to install the tire
pressure sensors.
NOTE
lMake sure the jack is well lubricated before
using it.
(With Tire Pressure Monitoring System)
lBe sure to register the tire pressure sensor
ID signal code whenever tires or wheels are
changed (page 5-34).
1. Park on a level surface off the right-of- way and firmly set the parking brake.
2. Put a vehicle with an automatic transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine. 3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, and tool (page 7-5).
6. Block the wheel diagonally opposite the tire to be changed. When blocking
a wheel, place a tire block both in front
and behind the tire.
NOTE
When blocking a tire, use rocks or wood blocks
of sufficient size if possible to hold the tire in
place.
In Case of an Emergency
Flat Tire
7-13
MX-5_8AV1-EA-09F_Edition5 Page315
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (364,1)
Light Bulbs
High-mount brake light
License plate lights
Trunk light
Reverse lights
Rear turn signal lights
Brake lights/Taillights
Rear side-marker lights
Overhead light
Headlights (Low beam) Headlights (High beam)Some models.
Fog lights
Front turn signal lights/Parking lights
Front side-marker lights
8-34
Maintenance and Care
Owner Maintenance
MX-5_8AV1-EA-09F_Edition5 Page364
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (369,1)
Front turn signal lights/Parking lights
1. If you are changing the right bulb, startthe engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
2. Make sure the turn signal switch is off.
3. Turn the center section of the plastic retainer counterclockwise and remove
the retainers and partially peel back the
mudguard.
Removal
Installation
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse orderof the removal procedure.
Rear turn signal lights, Reverse lights,
Brake lights/Taillights, Rear side
marker lights
Rear side marker lights
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
Rear turn signal lights, Reverse lights,
Brake lights/Taillights
1. Make sure the ignition is switched offand the applicable light switch is off.
2. Lift the trunk.
3. Pull the center section of the plastic retainers and remove them, then
remove the trunk end trim.
Removal
Installation
4. Remove the trunk light connector.
Maintenance and Care
Owner Maintenance
8-39
MX-5_8AV1-EA-09F_Edition5 Page369
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (370,1)
5. Remove the trunk lid release lock-outbutton connector.
6. On the side the bulb is to be replaced,
pull the center section of the plastic
retainers and remove them, then
remove the trunk side trim.
Removal
Installation
7. Disconnect the bulb from the socket. Rear turn signal lights
Reverse lights
Brake lights/Taillights
8. Install the new bulb in the reverse order
of the removal procedure.
8-40
Maintenance and Care
Owner Maintenance
MX-5_8AV1-EA-09F_Edition5 Page370
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (376,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
17 BTN 30 A For protection of various circuits
18 MAIN 120 A For protection of all circuits
19 EGI INJ 10 A Injector
20 EGI COMP1 10 A Engine control system
21 EGI COMP2 10 A Engine control system
22 HEAD LOW L 15 A Headlight low beam (LH)
23 HEAD LOW R 15 A Headlight low beam (RH)
24 HEAD 15 A Headlight high beams
25 P.WIND 20 A Power windows
26 ENGINE 15 A Engine control system
27 WIPER 20 A Windshield wipers and washer
28 DRL 15 A DRL
í
29HORN 15 A Horn
30 STOP 10 A Brake lights
31 ETV 10 A Electric throttle valve
32 FUEL PUMP 15 A Fuel Pump
33 HAZARD 10 A Turn signals, Hazard warning flashers
34 P.WIND2 20 A Power windows
í
35 IG KEY140 A For protection of various circuits
8-46
Maintenance and Care
íSome models.
Owner Maintenance
MX-5_8AV1-EA-09F_Edition5 Page376
Friday, May 7 2010 9:17 AM
Form No.8AV1-EA-09F

Black plate (436,1)
(Automatic transmission)Item Weight
Without power retractable hardtop With power retractable
hardtop
GVWR (Gross Vehicle Weight Rating) 1,396 kg (3,078 lbs) 1,416 kg (3,122 lbs)
GAWR (Gross Axle Weight Rating) Front 714 kg (1,574 lbs) 714 kg (1,574 lbs)
Rear 693 kg (1,528 lbs) 702 kg (1,548 lbs)
q
Air Conditioner
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R (SAE)
Headlights High beam 65
―(H9)
Low beam Halogen 55 H7 (H7)
Xenon fusion 35 D2S (D2S)
Front turn signal lights/Parking lights 28/8 ―(#7444NA)
Fog lights
í55 H11 (H11)
Front side-marker lights 5―(― )
High-mount brake light LED
*1―(― )
Rear turn signal lights 21 WY21W ( ―)
Brake lights/Taillights 21/5 W21/5W (#7443)
Reverse lights 18 W16W (#921)
License plate lights 5 W5W (4CP)
Rear side-marker lights LED
*1― (― )
*1 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulb Wattage
Overhead light 10
Trunk light 8
10-6íSome models.
Specifications
MX-5_8AV1-EA-09F_Edition5 Page436
Friday, May 7 2010 9:18 AM
Form No.8AV1-EA-09F

Black plate (442,1)
F
Flat Tire ............................................... 7-3Changing .................................... 7-13
Instant Mobility System
(IMS) Emergency Flat Tire Repair
Kit ................................................ 7-7
Tool storage .................................. 7-5
Fluids
Classification .............................. 10-4
Owner maintenance ................... 8-15
Fog Lights ......................................... 5-58
Foot Brake .......................................... 5-6
Fuel Filler lid and cap ........................ 3-40
Gauge ......................................... 5-39
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-42 Panel description ........................ 8-45
Replacement ............................... 8-42
G
Glove Box ......................................... 6-82
H
Hazard Warning Flasher .................... 5-61
Hazardous Driving .............................. 4-7
HeadlightsControl ....................................... 5-56
Flashing ...................................... 5-57
High-low beam .......................... 5-57
On reminder ............................... 5-56
HomeLink Wireless Control
System .............................................. 5-62
Hood Release .................................... 3-42
Horn .................................................. 5-61
I
Ignition
Keys ........................................... 3-23
Switch .......................................... 5-2
Immobilizer System
(with Advanced Key) ........................ 3-63
Immobilizer System
(without Advanced Key) ................... 3-67
Indicator Lights ................................. 5-41 Cruise ......................................... 5-53
DSC OFF .................................... 5-53
Headlight high-beam .................. 5-52
KEY ............................................ 5-50
Security ...................................... 5-52
Shift position .............................. 5-52
TCS/DSC ................................... 5-53
Turn-signal/hazard warning ....... 5-54
Inside Trunk Release Lever ............... 3-35
Instrument Cluster ............................. 5-36
Interior Care ...................................... 8-55
Interior Lights ................................... 6-80
J
Jump-Starting .................................... 7-21
K
Keyless Entry System ....................... 3-24
Keys .................................................. 3-23
L
Label Information ............................. 10-2
Lane-Change Signals ........................ 5-58
Light Bulbs Replacement ............................... 8-34
Specifications ............................. 10-6
Lighting Control ............................... 5-56
11-4
Index
MX-5_8AV1-EA-09F_Edition5 Page442
Friday, May 7 2010 9:18 AM
Form No.8AV1-EA-09F