light MAZDA MODEL MX-5 RF 2017 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL MX-5 RF, Model: MAZDA MODEL MX-5 RF 2017Pages: 609, PDF Size: 5.96 MB
Page 506 of 609
7–12
If Trouble Arises
Flat Tyre
NOTE
Check the tyre in À ation pressure
label driver's door frame for the
correct tyre in À ation pressure.
Do not operate the air compressor for
a continuous 10 minutes or longer
because using it for long periods
could cause a malfunction.
If the tyre in À ation pressure does
not increase, repair of the tyre is not
possible. If the tyre does not reach
the speci ¿ ed tyre in À ation pressure
within 10 minutes, it may have
received extensive damage. In this
case, the repair using the emergency
À at tyre repair kit was not successful.
Contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
If the tyre has been over-in À ated,
loosen the screw cap on the air
compressor and bleed some of the air
out.
20. When the tyre in À ates to the speci ¿ ed
tyre in À ation pressure, turn the air
compressor switch off, turn the sleeve
of the air compressor hose to the left,
and pull it out of the tyre valve.
21. Install the tyre valve cap.
22. Put the emergency À at tyre repair kit
into the boot.
23. Start driving immediately to spread the
sealant in the tyre.
CAUTION
Carefully drive the vehicle at a speed of
80 km/h (50 mph) or less. If the vehicle
is driven at a speed of 80 km/h (50 mph)
or more, the vehicle may vibrate.
NOTE
(With tyre pressure monitoring
system)
If the tyre is not properly in À ated, the
tyre pressure monitoring system warning
light will illuminate.
24. After driving the vehicle for about 10
minutes or 5 km (3 miles), connect the
air compressor to the tyre using Step
17 of the procedure, and check the
tyre in À ation pressure using the tyre
pressure gauge on the air compressor. If
the tyre in À ation pressure is lower than
the speci ¿ ed tyre in À ation pressure,
turn the air compressor on and wait
until it reaches the speci ¿ ed tyre
in À ation pressure.
WARNING
If the tyre in À ation pressure has
decreased below 130 kPa (1.3 kgf/cm 2
or bar, 18.9 psi), stop driving and
contact an expert repairer, we
recommend an Authorised Mazda
Repairer:
The repair using the emergency À at
tyre repair kit was not successful.
If you see a decrease in the tyre
in À ation pressure, even if Steps 17
to 24 of the procedure are performed
repeatedly, stop driving:
Contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 518 of 609
7–24
If Trouble Arises
Overheating
O v e r h e a t i n g
If the high engine coolant temperature
warning light turns on, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running inde ¿ nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and
radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the high engine coolant temperature
warning light turns on:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the bonnet and start the engine.
If neither coolant nor steam is
escaping:
Open the bonnet and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 525 of 609
7–31
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
If a Warning Light Turns On or Flashes
If any warning light turns on/ À ashes, take appropriate action for each light. There is no
problem if the light turns off, however if the light does not turn off or turns on/ À ashes again,
consult an Authorised Mazda Repairer.
(Vehicles with type B/type C audio)
The warning contents can be veri ¿ ed on the centre display.
1. If the warning light is turned on, select
icon on the home screen to display the
application screen.
2. Select “Vehicle Status Monitor”.
3. Select “Warning Guidance” to display the current warnings.
4. Select the applicable warning to view the warning details.
Stop Vehicle in Safe Place Immediately
If any of the following warning lights turns on, the system may have a malfunction. Stop the
vehicle in a safe place immediately and contact an Authorised Mazda Repairer.
Signal Warning
(Red)
Brake System Warning
Light
This warning has the following functions:
Parking brake warning/Warning light inspection
The light illuminates when the parking brake is applied with the ignition switched to
START or ON. It turns off when the parking brake is fully released.
Low brake À uid level warning
If the brake warning light remains illuminated even though the parking brake is
released, the brake À uid may be low or there could be a problem with the brake
system. Park the vehicle in a safe place immediately and contact an expert repairer, we
recommend an Authorised Mazda Repairer.
WARNING
Do not drive with the brake system warning light illuminated. Contact an expert
repairer, we recommend an Authorised Mazda Repairer to have the brakes
inspected as soon as possible:
Driving with the brake system warning light illuminated is dangerous. It
indicates that your brakes may not work at all or that they could completely fail
at any time. If this light remains illuminated, after checking that the parking
brake is fully released, have the brakes inspected immediately.
CAUTION
In addition, the effectiveness of the braking may diminish so you may need to
depress the brake pedal more strongly than normal to stop the vehicle.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 526 of 609
7–32
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Electronic Brake Force
Distribution System
Warning If the electronic brake force distribution control unit determines that some components
are operating incorrectly, the control unit may illuminate the brake system warning
light and the ABS warning light simultaneously. The problem is likely to be the
electronic brake force distribution system.
WARNING
Do not drive with both the ABS warning light and brake warning light
illuminated. Have the vehicle towed to an expert repairer, we recommend an
Authorised Mazda Repairer to have the brakes inspected as soon as possible:
Driving when the brake system warning light and ABS warning light are
illuminated simultaneously is dangerous.
When both lights are illuminated, the rear wheels could lock more quickly in an
emergency stop than under normal circumstances.
Charging System
Warning Indication/
Warning Light If the warning light illuminates while driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off the right-of-way. Consult an expert repairer,
we recommend an Authorised Mazda Repairer. CAUTION
Do not continue driving when the charging system warning light is illuminated
because the engine could stop unexpectedly.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 527 of 609
7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-20 . If it's low, add the appropriate amount of engine
oil while being careful not to over ¿ ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Indication/Warning
Light
The light À ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can ¿ nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-24 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 528 of 609
7–34
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
Power Steering
Malfunction Indicator
Light The light illuminates if the electric power steering has a malfunction.
If the light illuminates, stop the vehicle in a safe place and do not operate the steering
wheel. There is no problem if the light turns off after a while. Contact an expert
repairer, we recommend an Authorised Mazda Repairer if the light illuminates
continuously.
NOTE
If the indicator light illuminates, the power steering will not operate normally. If
this happens, the steering wheel can still be operated, however, the operation may
feel heavy compared to normal, or the steering wheel could vibrate when turning.
Repeatedly jerking the steering wheel left and right while the vehicle is stopped
or moving extremely slowly will cause the power steering system to go into
protective mode which will make the steering feel heavy, but this does not indicate
a problem. If this occurs, park the vehicle safely and wait several minutes for the
system to return to normal.
Contact Authorised Mazda Repairer and Have Vehicle Inspected
If any of the following warning lights or the indicator light turns on/ À ashes, the system
may have a malfunction. Contact an expert repairer, we recommend an Authorised Mazda
Repairer to have your vehicle inspected.
Signal Warning
Master Warning
Indication/Warning
Light
*
Type A instrument cluster
(Master warning indication)
Displays when noti ¿ cation of the system malfunctions is required.
Check the message indicated in the display and consult an expert repairer, we recommend
an Authorised Mazda Repairer.
(Master warning light)
The master warning light displays when a warning message occurs.
This indicates a malfunction with the vehicle system. Check the message indicated in the
display and consult an expert repairer, we recommend an Authorised Mazda Repairer.
For details, refer to the explanations for the warning/indicator lights, in the warning/
indicator lights section, which match the symbol in the upper part of the display.
If a message is not indicated in the display, operate the INFO switch to display the
“Warning” screen.
Refer to Message Indicated in Multi-information Display and INFO switch on page 4-33 .
Type B instrument cluster
The light illuminates continuously if any one of the following occurs. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
There is a malfunction in the battery management system. There is a malfunction in the brake switch.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 529 of 609
7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
(Amber)
Electric Vacuum
Pump Warning
Light The light turns on if the electric vacuum pump system has a problem. Have your vehicle
inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally as if the vehicle had
no ABS.
Should this happen, consult an expert repairer, we recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and
does not indicate an ABS malfunction.
Recharge the battery.
The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
The engine's electrical system has a problem. The emission control system has a problem. The fuel tank level being very low or approaching empty. The fuel- ¿ ller cap is missing or not tightened securely.
If the check engine light remains on, or it À ashes continuously , do not drive at high speeds
and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
(Amber)
i-stop Warning
Light
*
When the light is turned on
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light does not turn on when the ignition is switched ON. The light continues to remain on even though the i-stop OFF switch has been pressed
while the engine is running.
When the light is À ashing
The light continues to À ash if the system has a malfunction. Have your vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
i-ELOOP
Indication/Warning
Light
*
The Warning indication/Warning light turns on if there is any malfunction in the i-ELOOP
system. Consult an expert repairer, we recommend an Authorised Mazda Repairer.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 530 of 609
7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
Automatic
Transmission
Indication/Warning
Light
*
The indication/light illuminates when the transmission has a problem.
CAUTION
If the automatic transmission warning indication/light illuminates, the transmission has
an electrical problem. Continuing to drive your Mazda in this condition could cause
damage to your transmission. Consult an expert repairer, we recommend an Authorised
Mazda Repairer as soon as possible.
(Illuminate)
TCS/DSC Indicator
Light If the light stays on, the TCS, DSC or the brake assist system may have a malfunction and
they may not operate correctly. Take your vehicle to an expert repairer, we recommend an
Authorised Mazda Repairer.
Air Bag/Seat Belt
Pretensioner System
Warning Light A system malfunction is indicated if the warning light constantly À ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
Active Bonnet
Warning Light *
The light turns on when the ignition is switched on for an operation check, and turns off a
few seconds later.
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light does not turn on when the ignition is switched ON. Remains turned on/ À ashing.
WARNING
Do not drive the vehicle with the active bonnet warning light turned on or À ashing:
Driving the vehicle with the active bonnet warning light turned on or À ashing is
dangerous as the active bonnet mechanism may not activate normally and function
as intended in the event the vehicle were to contact a pedestrian.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 531 of 609
7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
(Flashing)
Tyre Pressure
Monitoring System
Warning Light
*
Vehicle with conventional tyres
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light À ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
Vehicle with run- À at tyres
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning light
À ashes. Have your vehicle checked by an expert repairer, we recommend an Authorised
Mazda Repairer as soon as possible.
WARNING
If the tyre pressure monitoring system warning light illuminates or À ashes, or the tyre
pressure warning beep sound is heard, decrease vehicle speed immediately and avoid
sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or À ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a À at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.
Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.
FLAT TIRE
Warning Light *
If a run- À at tyre is punctured, the FLAT TIRE warning light illuminates in the instrument
cluster, and a beep sound is heard for about 30 seconds.
Carefully drive the vehicle to the nearest Mazda repair shop immediately and have the À at
tyre replaced.
Refer to Vehicle with Run- À at Tyres on page 7-3 .
WARNING
Have the tyres checked or perform the appropriate repair as soon as possible by an
expert repairer, we recommend an expert repairer, we recommend an Authorised
Mazda Repairer:
When the À at tyre warning light illuminates or the tyre pressure warning beep
sound is heard, it is dangerous to drive the vehicle at high speeds, or perform sudden
manoeuvring or braking. Vehicle drivability could worsen and result in an accident.
When the À at tyre warning light illuminates or the tyre pressure warning beep sound
is heard, decrease vehicle speed immediately and avoid sudden manoeuvring and
braking.
/ : A ( . ' ' , A ' F K V K Q P K P F D
Page 532 of 609
7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning
(Red)
KEY Warning
Indication
*
“Keyless System malfunction” is displayed
This message is displayed if the advanced keyless entry & push button start system has a
problem.
Contact an expert repairer, we recommend an Authorised Mazda Repairer.
CAUTION
If the message is indicated, or the push button start indicator light (amber) À ashes, the
engine may not start. If the engine cannot be started, try starting it using the emergency
operation for starting the engine, and have the vehicle inspected at an expert repairer,
we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
(Amber)
KEY Warning
Indication
*
“Set Power to OFF” is displayed
This message is displayed when the driver's door is opened without switching the ignition
off.
“Key not found” is displayed
This message is displayed when any of the following operations is performed with the key
out of the operational range or placed in areas inside the cabin where it is dif ¿ cult for the
key to be detected.
The push button start is pressed with the ignition switched off The ignition is switched on All doors are closed without switching the ignition off
(Red)
(Illuminate)
KEY Warning
Light
*
If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) À ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
/ : A ( . ' ' , A ' F K V K Q P K P F D